Sony Projector VPL-FH65 User Manual

11
INPUT A
For connecting video equipment with a YPBPR output terminal.
INPUT C
For connecting video equipment with an HDMI output terminal.
 Use HDMI-compatible equipment which has the HDMI Logo.
 Use a high speed HDMI cable(s) on which the cable type logo is specified. (Sony products are 
recommended.)
 The HDMI terminal of this projector is not compatible with DSD (Direct Stream Digital) signal or 
CEC (Consumer Electronics Control) signal.
Notes
Component – Mini D-
sub 15-pin cable (not 
supplied)...

12
To fix the HDMI cable
Fix the cable to the cable tie holders at the sides of the terminals using a commercially available 
cable tie, as shown in the illustration.
Use a cable tie of less than 1.9 mm × 3.8 mm in thickness.
Projected images and input audio can be output to display equipment such as a monitor and 
audio equipment such as speakers with a built-in amplifier.
OUTPUT A
This terminal outputs projected images. The images are output when a computer signal or video 
signal is input from the...

13
OUTPUT B
This terminal outputs projected images. The images are output when a computer signal is input 
from the DVI-D input terminal (INPUT B). However, if the signal input from INPUT B is 
protected by HDCP, the signal is not output to OUTPUT B.
AU D I O ou tpu t
When INPUT A or B, or VIDEO is selected, the audio input from the audio input terminal is 
output; when INPUT C or D is selected, the audio input from the selected input terminal is 
output.
Connecting network equipment
LAN terminal
When...

14
For connecting the computer, video equipment, and network equipment via the HDBaseT 
transmitter.
Connecting to the computer
INPUT D
Connecting to video equipment
INPUT D
Notes for connecting this unit and the HDBaseT transmitter
 Ask a professional or Sony dealer to perform wiring. If wiring is not correct, the transmission 
characteristics of the cable will not be achieved, and image or sound may break up or you 
may experience unstable performance.
 Connect the cable directly to the HDBaseT...

15
 The transmittable distance of the cable is 100 m (approx. 328 feet) maximum. If it exceeds 
100 m (approx. 328 feet), it may cause the image or the sound to break up, or cause a 
multifunction in LAN communication. Do not use the HDBaseT transmitter beyond the 
transmittable distance.
 Inquire about operation or function problems caused by other manufacturer’s devices with 
the relevant manufacturer.
Connecting to network equipment
For connecting to network equipment via the HDBaseT terminal to...

16
You can attach the supplied terminal cover to 
prevent dust from entering the terminals to 
maintain a neat appearance.
1Fit one shaft on the side of the terminal 
cover into the hole on the bottom, then 
fit the other shaft by bending the cover 
slightly.
2Close the terminal cover.
Close the terminal cover until the two 
tabs on the terminal cover click.The terminal cover may not be attached 
depending on the installation method, such 
as due to the condition of the connected 
cables or when...

17
BProjecting/Adjusting an Image
Projecting an Image
The size of a projected image depends on the distance between the projector and screen. Install 
the projector so that the projected image fits the screen size. For details on projection distances 
and projected image sizes, see 
“Projection Distance and Lens Shift Range” (page 63).
1Plug the AC power cord into a wall 
outlet.
2Connect all equipment to the projector 
(page 9).
3Turn on the projector.
Press the ?/1 key on the main unit or the 
? key on...

18
Adjusting the tilt of the projector 
with the front feet (adjustable)
When the projector is installed on an uneven 
surface, you can adjust using the front feet 
(adjustable). 
 Be careful not to let the projector down on 
your fingers.
 Do not push hard on the top of the projector 
with the front feet (adjustable) extended. It 
may cause a malfunction.
Displaying a pattern for adjusting 
an image
You can display a pattern for adjusting the 
projected image with the PATTERN key on 
the Remote...

19
If the screen is tilted, or you are projecting 
from an oblique angle, perform keystone 
adjustment.
If the projected image is 
trapezoidally-distorted in the 
vertical plane
1Press the KEYSTONE key on the 
Remote Commander once or select 
“Screen Fitting” in the Installation 
menu (page 36).
The “Screen Fitting” menu is displayed.
2Select “V Keystone.”
3Adjust the value using B/b.
The higher the setting, the narrower the 
top of the projected image. The lower 
the setting, the narrower the bottom of...

20
You can correct image twist with the warp 
correction feature.
1Press the KEYSTONE key on the 
Remote Commander once or select 
“Screen Fitting” in the Installation 
menu (page 36).
The “Screen Fitting” menu is displayed.
2Select “Warping.”
The guide is displayed.
When correcting the corner(s) of 
the image
1Move x using V/v/B/b to select the 
corner you want to correct.
2Press the ENTER key.
The cursor appears.
3Adjust the position of the corner you 
want to correct, using V/v/B/b.
Press the RESET...