Sony Projector VPL-EW348 User Manual

31The Connection/Power Menu
Adjustments and Settings Using a Menu
The Connection/Power Menu
The Connection/Power menu is used for setting for the connections and power.
Items Item descriptions
LAN Settings
IP Address 
Setup
*9Auto (DHCP): The IP address is assigned automatically from the 
DHCP server such as a router.
Manual: To specify the IP Address manually.
WLAN Settings
*10
WLAN 
Connection*8On/Off: Set the wireless output of the USB wireless LAN module (not 
supplied) to On/Off.
WLAN 
Network...

32The Connection/Power Menu
*1: This may not be optimum depending on the input signal. In this case set manually according 
to the connected equipment.
*2: When “Standby Mode” is set to “Low,” the network and network control function cannot be 
operated while the projector is in standby mode.
*3: This varies depending on the “Lamp Mode” setting. 
*4: As the lamp is dimmed gradually, you may not notice any change in brightness. You might only 
notice that the lamp has dimmed when its brightness is...

33The Connection/Power Menu
Adjustments and Settings Using a Menu
*5: This mode does not work for about three minutes after the lamp lights. A change in signal may 
not be detected depending on the input image. The lamp may become brighter at intervals 
during lamp dimming. However, this is not a malfunction. If With No Input is set, it takes 
priority.
*6: Select “Off” to avoid entering standby mode when there is no input signal.
*7: Does not function when “Type A USB”, “Type B USB” or “Network” is...

34The Installation Menu
The Installation Menu
The Installation menu is used for installing the projector.
*1: When “High Altitude Mode” is set to “On,” the speed of the fan increases, and the fan noise 
becomes slightly louder.
*2: Since the Keystone adjustment is an electronic correction, the image may be deteriorated.
*3: Since Digital Shrink uses electronic correction, the image may deteriorate.
*4: If you press the ENTER button while adjusting with Digital Shrink, the projector switches to the 
shift...

35The Information Menu
Adjustments and Settings Using a Menu
The Information Menu
The Information menu is used to check projector status, such as total usage time of the lamp.
*1: These items may not be displayed depending on the input signal.Items Item descriptions
Model Name Displays the model name.
Serial No. Displays the serial number.
fH/fV
*1Displays the horizontal/vertical frequency of the current input signal.
Signal Type Displays the type of the current input signal.
Lamp Timer Indicates the...

36Using Network Features
BNetwork
Using Network Features
Connection to the network allows you to operate the following features:
 Checking the current status of the projector via a Web browser.
 Remotely controlling the projector via a Web browser.
 Receiving the e-mail report via the projector.
 Making the network settings for the projector.
 Displaying messages on the projected image using an application.
 Supports network monitoring, control protocol (Advertisement, PJ Talk, PJ Link, AMX 
DDDP...

37Using Network Features
Network
The following window appears in the 
Web browser:
Once you make the network settings, 
you can open the Control window only 
by performing step 3 of this procedure.
How to operate the Control window
Switching the page
Click one of the Page Switching buttons to 
display the desired setting page.
Setting the access limitation
You can limit a user for accessing any 
particular page.
Administrator: Allowed access to all 
pages
User: Allowed access to all pages except 
the...

38Using Network Features
You can control the projector from the 
computer on the Control page.
The functions of the buttons shown in the 
operation area are the same as the keys on 
the remote commander.
Set the e-mail report function on the Setup 
page.
Entered values will not be applied unless 
you click on [Apply].
1Click on [Owner information] to enter 
the owner information recorded in the 
e-mail report.
2Set the timing of the e-mail report.
Click on [Mail Report] to open the Mail 
Report page.Lamp...

39Using Network Features
Network
Requires the use of POP 
Authentication before sending email 
(POP before SMTP): Check this 
check box to arrange for POP 
authentication to be performed before 
sending e-mail.
Incoming Mail Server (POP3): Enter 
the address of the incoming-mail 
server (POP3) to be used for POP 
authentication.
Account Name: Enter the mail account 
name.
Password: Enter the password.
SMTP Authentication: Check this 
check box to arrange for SMTP 
authentication to be performed before...

40Using Network Features
To use the wireless LAN network, a USB 
wireless LAN module IFU-WLM3 (not 
supplied) is necessary.
1Click the [WLAN Setting] to open the 
WLAN Setting page.
2Enable or disable the radio wave 
output of USB wireless LAN module.
Wireless ON: Enables radio wave 
output of USB wireless LAN module.
Wireless OFF: Disables radio wave 
output of USB wireless LAN module.
WLAN Network: Set the modes for 
USB wireless LAN module.
3(a) Input the settings for Access 
Point Mode.
When the USB...