Sony Projector VPL-EW246 Manual

							21The Screen Menu
Adjustments and Settings Using a Menu
The Screen Menu
The Screen menu is used to adjust the size, position and aspect ratio of the projected image for 
each input signal.
Items Item descriptions
Aspect
*1Changes the aspect ratio of the projected image (page 23).
VPL-EW276/EW246/
EW226: When the 
computer signal is 
input4:3: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 16:9.
Full 1: Displays the image to fit the maximum projected image 
size without changing the aspect ratio of the input signal.
Full 2: Displays the image to fit the maximum projected image 
size changing the aspect ratio of the input signal.
Full 3: Displays the image to fit the maximum width or height, up 
to 1280 × 720 pixels, without changing the aspect ratio of the 
input signal.
Normal: Displays the image on the center position of the 
projected screen without changing the resolution of the input 
signal or enlarging the image.
VPL-EW276/EW246/
EW226: When the 
video signal is input4:3: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 16:9.
Full: Displays the image to fit the maximum projected image size 
changing the aspect ratio of the input signal.
Zoom: Zooms the center area of a projected image.
VPL-EX276/EX272/
EX246/EX242/
EX226/EX222: When 
the computer signal is 
input4:3: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 16:9.
Full 1: Displays the image to fit the maximum projected image 
size without changing the aspect ratio of the input signal.
Normal: Displays the image on the center position of the 
projected screen without changing the resolution of the input 
signal or enlarging the image.
VPL-EX276/EX272/
EX246/EX242/
EX226/EX222: When 
the video signal is 
input4:3: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 4:3.
16:9: Displays the image to fit the maximum projected image size 
with an aspect ratio fixed to 16:9.
Zoom: Zooms the center area of a projected image. 
						

							22The Screen Menu
*1:   Note that if the projector is used for profit or for public viewing, modifying the original picture 
by switching to the aspect mode may constitute an infringement of the rights of authors or 
producers, which are legally protected.
 Depending on the input signal, setting items for aspect ratio or some other setting items cannot 
be set in some cases, or changing the aspect ratio setting may have no effect.
 A part of the image may be displayed in black, depending on the setting item.
*2: Available when a computer signal is input from the RGB input connector (INPUT A/INPUT B).
*3: If the projected image includes large amount of black portion around it, the APA function will 
not work properly and a part of the image may not be displayed on the screen and also optimum 
image cannot be obtained, depending on the type of input signal. In this case, adjust the “Phase,” 
“Pitch,” and “Shift” items manually.
*4: Available when a computer or a video signal is input from the RGB/YP
BPR input connector 
(INPUT A). Adjust Signal Adjusts the image of computer signal. Use this item if the edge of 
the image is cut and reception is bad.
APA
*2 *3Automatically adjusts the projected image to an optimum quality 
when you press the ENTER key (page 6).
Phase
*2Adjusts the dot phase of the display pixel and the input signal. Set 
to the value where looks clearest.
Pitch
*2The higher the value, the wider the horizontal image elements 
(pitch). The lower the value, the narrower the horizontal image 
elements (pitch).
Shift
*4H (Horizontal): The higher the value, the farther right the image 
is projected on the screen. The lower the value, the image farther 
left.
V (Vertical): The higher the value, the farther up the image is 
projected on the screen. The lower the value, the image farther 
down.
Notes
Items Item descriptions 
						

							23The Screen Menu
Adjustments and Settings Using a Menu
Aspect
VPL-EW276/EW246/EW226*1: If you select “Normal,” the image is 
projected in the same resolution as the 
input signal without changing the aspect 
ratio of the original image.
*2: If you select “Full2,” the image is projected 
to fit the projected image size, regardless 
of the aspect ratio of the image.
*3: If you adjust the projected image position 
using an image with 16:9 aspect ratio and 
then switch the input source to 4:3 image, 
the top and bottom edge of the image may 
be hidden. In this a case, select “Full3.”
*4: Depending on the input signal, the 
projected image may be projected as 
illustrated below. In this a case, select 
“16:9.”
*5: Depending on the input signal, the image 
may be projected as illustrated below. In 
this a case, select “Zoom.” Input signal Recommended 
setting value and 
projected image
Computer signal
4:3 Full1*1 *2 *3
16:9 Full1*1 *2 *3
16:10 Full1*3
Video signal
4:3 4:3*4 *5
16:9 16:9 
						

							24The Screen Menu
VPL-EX276/EX272/EX246/EX242/
EX226/EX222*1: If you select “Normal,” the image is 
projected in the same resolution as the 
input signal without changing the aspect 
ratio of the original image.
*2: If you select “4:3,” the image is projected 
to fit the projected image size, regardless 
of the aspect ratio of the image.
*3: Depending on the input signal, the 
projected image may be projected as 
illustrated below. In this a case, select 
“16:9.”
*4: Depending on the input signal, the 
projected image may be projected as 
illustrated below. In this a case, select 
“Zoom.” Input signal Recommended 
setting value and 
projected image
Computer signal
4:3
Full1*1
16:9
Full1*1 *2
16:10 Full1*1 *2
Video signal
4:3 4:3*3 
16:9 16:9
*4 
						

							25The Function Menu
Adjustments and Settings Using a Menu
The Function Menu
The Function menu is used for setting various functions of the projector.
*1: APA functions when a computer signal is input via the RGB input connector (INPUT A/INPUT 
B).
*2: The maximum available mic volume is set by the value of “Volume.”
*3: VPL-EW276/EW246/EW226/EX276/EX246/EX226 only.Items Item descriptions
Volume
*3The higher the value, the louder an audio volume and the lower the 
value, the lower the audio volume.
Mic Volume
*3Adjust the volume of the microphone.*2
Speaker*3On/Off: When set to “On,” speaker outputs sound. To not output 
sound from the speaker, select “Off.”
Smart APAOn/Off: When set to “On,” APA functions automatically when a 
signal is input.
*1
CC DisplayCC1/CC2/CC3/CC4/Text1/Text2/Text3/Text4: Select the closed 
caption service (captions or text).
Off: Closed caption does not appear.
Lamp Timer Reset When replacing the lamp, resets the lamp timer (page 47).
Start Up ImageOn/Off: When set to “On,” the Start Up Image is displayed on the 
screen when the projector is powered on.
Notes 
						

							26The Operation Menu
The Operation Menu
The Operation menu is used for setting for the operations by using the menu or the remote 
commander.
*1: You will not be able to use the projector if you forget your password. If you call qualified Sony 
personnel because you have forgotten the password, you will be asked to verify the projector’s 
serial number and your identity. (This process may differ in other countries/regions.) Once your 
identity has been confirmed, we will provide you with the password. Items Item descriptions
Language Selects the language used in the menu and messages.
StatusOn: All on-screen statuses are enabled.
Off: Turns off the on-screen displays, except for menus, warning messages 
and messages from the message list.
Security Lock
*1On/Off: This function enables restriction of the projector to authorized users 
by password. The setting procedures for security locking are as follows:
1Select “On” and press the ENTER key to display the setting menu.
2Input the password with the MENU, V/v/B/b and ENTER keys. (The 
default setting password is “ENTER, ENTER, ENTER, ENTER.”)
3Input a new password with the MENU, V/v/B/b and ENTER keys.
4Enter the password again to confirm.
Enter the password when you turn on the projector after disconnecting and 
reconnecting the AC power cord.
When it is set to “Off,” you can cancel the security lock. You are required to 
input the password again.
If you fail to enter the correct password after three consecutive times, the 
projector cannot be used. In this case, press the ?/1 key to go Standby mode 
then turn on the power again.
Control Key 
LockOn/Off: When set to “On,” locks all the control panel keys of the projector. 
However, you can operate the following when set to “On”:
 Press and hold the ?/1 key for approximately 10 seconds during Standby 
mode.
c The projector turns on.
 Press and hold the MENU key for approximately 10 seconds during power 
on.
c“Control Key Lock” is set to “Off” and enables operation of all keys on 
the projector.
Note 
						

							27The Connection/Power Menu
Adjustments and Settings Using a Menu
The Connection/Power Menu
The Connection/Power menu is used for setting for the connections and power.
Items Item descriptions
LAN Settings
IP Address 
Setup
*9Auto (DHCP): The IP address is assigned automatically from the 
DHCP server such as a router.
Manual: To specify the IP Address manually.
WLAN Settings
*10
WLAN 
Connection*8On/Off: Set the wireless output of the USB wireless LAN module (not 
supplied) to On/Off.
Access Point 
SetupAu to / Ma n u a l 
*11: Set the access point automatically or manually.
Input-A Signal Sel.
Auto/Computer/Video GBR/Component: When set to “Auto,” selects 
the type of video signal input automatically when “Input-A” is selected. *1
ECO
Lamp ModeHigh/Standard/Low/Auto
*5 *7: When set to “High,” the image 
becomes brighter, and power consumption becomes higher. When set to 
“Low,” power consumption is minimized; however, the image will be 
darker. When set to “Auto,” brightness is adjusted automatically 
according to image content. Dark images are projected with brightness 
adjusted, leading to energy-saving. Bright images are projected 
brightly, without adjusting brightness.
Auto Power Saving
With No InputLamp Cutoff: The lamp turns off automatically and power 
consumption is reduced if no signal is input for more than 10 minutes.
The lamp lights again when a signal is input or any key is pressed. In 
Lamp Cutoff, the ON/STANDBY indicator lights in orange. (page 43)
Standby*
6: If no signal is input to the unit for more than 10 minutes, 
the power turns off automatically, and the unit enters standby mode.
Off: You can deactivate the With No Input.
With Static 
SignalLamp Dimming
*4 *5 *7: If an image does not change for about 10 
seconds, lamp output is gradually reduced (approximately 10% to 
15%*
3) from that set in the Lamp Mode. Automatically the lamp slowly 
darkens to approximately 30% of its lamp output according to the 
selected time (with no change to input signal) “5,”  “10,”  “15,”  “20” 
minutes or “Demo.,” While dimming the lamp, the message “Lamp 
Dimming” appears. If you select “Demo.,” the image will start to 
darken about 40 seconds later. When any change in signal is detected, 
or an operation (remote control or control panel) is performed, normal 
brightness is restored.
Off: You can deactivate the With Static Signal.
Standby Mode*
2Standard/Low: When set to “Low,” lowers power consumption in 
Standby mode. 
						

							28The Connection/Power Menu
*1: This may not be optimum depending on the input signal. In this case set manually according 
to the connected equipment.
*2: When “Standby Mode” is set to “Low,” the network and network control function cannot be 
operated while the projector is in standby mode.
*3: This varies depending on the “Lamp Mode” setting. 
*4: As the lamp is dimmed gradually, you may not notice any change in brightness. You might only 
notice that the lamp has dimmed when its brightness is restored after there is a change in input 
signal.
*5: This mode does not work for about three minutes after the lamp lights. A change in signal may 
not be detected depending on the input image. The lamp may become brighter at intervals 
during lamp dimming. However, this is not a malfunction. If With No Input is set, it takes 
priority.
*6: Select “Off” to avoid entering standby mode when there is no input signal.
*7: Does not function when “Type A USB”, “Type B USB” or “Network” is selected as the input. 
In this case, it becomes equivalent to “Standard.”
*8: Reflecting changes in WLAN settings may take a few moments.
*9: To set the IP address manually, select “Manual”, press “Apply”, then enter the IP address.
*10: When you send images or files from a tablet device and display them (page 37), USB wireless 
LAN module IFU-WLM3 (optional) can be used as a wireless access point.
*11: The factory default settings for “Manual” are as follows.
SSID: VPL + MAC address for LAN
Security Method: WEP(64bit)
Password: sony1
To change the settings for “Manual”, use a web browser.
If “Manual” is set, when you use Presentation Function via Network (page 35), select “Manual 
Connect” to connect to the network. Direct Power OnOn/Off: When set to “On,” you can turn the power on without going to 
Standby mode when the AC power cord is connected to a wall outlet. 
With the projector turned off, you can also unplug the AC power cord 
without going to Standby mode, regardless of the Direct Power On 
setting. 
Notes
Items Item descriptions 
						

							29The Installation Menu
Adjustments and Settings Using a Menu
The Installation Menu
The Installation menu is used for installing the projector.
*1: When “High Altitude Mode” is set to “On,” the speed of the fan increases, and the fan noise 
becomes slightly louder.
*2: Since the Keystone adjustment is an electronic correction, the image may be deteriorated.Items Item descriptions
Image FlipHV/H/V/Off: Flips the projected image horizontally or vertically 
according to the installation method.
Installation AttitudeRight Side Up/Upside Down/Link to Image Flip: Change the cooling 
setting to suit to the installation attitude. When set to “Link to Image Flip,” 
the cooling setting changes based on the setting of “Image Flip.” 
Continuing to use the wrong setting may affect component reliability.
High Altitude 
Mode
*1On/Off: Set to “On” when using the projector at an altitude of 1,500 m or 
higher. Continuing to use the wrong setting may affect component 
reliability.
V Keystone
*2Au to / Ma n u a l*2: The higher the value, the narrower the top of the 
projected image. The lower the value, the narrower the bottom.
Notes 
						

							30The Information Menu
The Information Menu
The Information menu is used to check projector status, such as total usage time of the lamp.
*1: These items may not be displayed depending on the input signal.Items Item descriptions
Model Name Displays the model name.
Serial No. Displays the serial number.
fH/fV
*1Displays the horizontal/vertical frequency of the current input signal.
Signal Type Displays the type of the current input signal.
Lamp Timer Indicates the total usage time of a lamp.
Note