Sony Projector VPL-EW246 Manual

							11Connecting the Projector
Preparation
VIDEO IN 
For connecting video equipment with a video output connector.
The audio input connector is available only on VPL-EW276/EW246/EW226/EX276/EX246/
EX226.
INPUT A
For connecting video equipment with a YPBPR output connector.
The audio input connector is available only on VPL-EW276/EW246/EW226/EX276/EX246/
EX226.
Note
Note
Video cable (not supplied)
Audio cable (Phono plug × 2 – stereo mini plug) (not supplied)Video output 
connector
Audio output 
connector
Video equipment
Component – Mini D-sub 15-pin cable (not supplied)
Audio cable (Phono plug × 2 – stereo mini plug) (not supplied) Video equipmentYP
BPR output 
connector
Audio output 
connector 
						

							12Connecting the Projector
INPUT C
 Audio output from the HDMI connector is available only on VPL-EW276/EW246/EW226/
EX276/EX246/EX226.
 Use HDMI-compatible equipment which has the HDMI Logo. 
 Use a high speed HDMI cable(s) on which the cable type logo is specified. (Sony products are 
recommended.)
 The HDMI connector of this projector is not compatible with DSD (Direct Stream Digital) Signal 
or CEC (Consumer Electronics Control) Signal.
Microphone ( )
For connecting a microphone.
 The microphone input is available only on VPL-EW276/EW246/EW226/EX276/EX246/EX226.
 Only dynamic microphones are supported.
USB connector (Type A) ( )
For connecting a USB memory device (“Using USB Media Viewer” (page 39)).
Notes
Connecting a microphone
Notes
Connecting a USB memory device
Video equipmentHDMI cable 
(not supplied)
HDMI output 
connector
For connecting video equipment with an HDMI output connector.
Microphone 
(not supplied)
USB memory device 
(not supplied) 
						

							13Connecting the Projector
Preparation
USB connector (Type A) ( )
For connecting a USB wireless LAN module IFU-WLM3 (not supplied) (“Presentation 
Function via Network” (page 35)).
 Undesignated USB wireless LAN modules do not work.
 When connecting/disconnecting the USB wireless LAN module, make sure that the projector is in 
Standby mode (Standby Mode: “Low”), or the AC power cord is unplugged from the wall outlet.
OUTPUT
Projected images or input audio can be output to display equipment such as a monitor or audio 
equipment such as speakers with a built-in amplifier.
 The audio input connector is available only on VPL-EW276/EW246/EW226/EX276/EX246/
EX226.
 Projected images and audio can be output.
Connecting a USB wireless LAN module
Notes
Connecting an External Monitor and Audio Equipment
Notes
USB wireless LAN module 
IFU-WLM3 (not supplied)
Audio cable 
(stereo mini plug) 
(not supplied)Audio input 
connector
Mini D-sub 15-pin cable 
(supplied) RGB input 
connector Audio equipment
Display equipment 
						

							14Projecting an Image
BProjecting/Adjusting an Image
Projecting an Image
The size of a projected image depends on the distance between the projector and screen. Install 
the projector so that the projected image fits the screen size. For details on projection distances 
and projected image sizes, see 
“Projection Distance” (page 58).
1Plug the AC power cord into the wall 
outlet.
2Connect all equipment to the projector 
(page 9).
3Press the ?/1 key to turn on the unit.
4Turn on the connected equipment.
5Select the input source.
Press the INPUT key on the projector to 
display the menu for switching input 
signal on the screen. Press the INPUT 
key repeatedly, or press the 
V/v key to 
select an image to be projected.
6When projecting a computer image, 
switch your computer’s output to 
external display. 
The method to switch the output varies 
depending on the type of computer.
(Example)
To project image files stored in a USB 
memory device, see “USB Media 
Viewer” (page 39). To project an image 
using USB Connection, see “Projecting 
an Image using USB Connection” 
(page 38). To use Presentation Function 
via Network, see “Presentation Function 
via Network” (page 35).
Computer Video equipment
Projector
Wall outlet
125
43
6
+ 
						

							15Projecting an Image
Projecting/Adjusting an Image
7Adjust the focus, size and position of 
the projected image (page 15).
Adjusting the Projected image
Focus Size (Zoom) Position
Focus ring
Zoom ring
Foot 
adjust 
button
Front feet 
(adjustable) 
						

							16Projecting an Image
Adjusting the tilt of the projector with the front feet (adjustable)
By changing the tilt of the projector with the foot adjust buttons/front feet (adjustable), you can 
adjust the position of the projected image.
How to adjust the angle
1Press and hold the foot adjust buttons.
2Lift up the front of the projector to 
adjust the angle.
3Release the foot adjust buttons.
4Turn the front feet (adjustable) to set 
the angle of the projector precisely.
 Be careful not to let the projector down on your fingers.
 Do not push hard on the top of the projector with the front feet (adjustable) extended.
Changing the aspect ratio of the projected image
Press the ASPECT key on the remote commander to change the aspect ratio of the projected 
image. You can also change the setting in Aspect of the Screen menu (pages 21, 23).
Notes 
						

							17Projecting an Image
Projecting/Adjusting an Image
Correcting trapezoidal distortion of the projected image (Keystone feature) 
Normally the Keystone feature automatically adjusts the projected image. The Keystone 
feature may not work automatically if the screen is tilted. In this case, set Keystone manually.
1Press the KEYSTONE key on the remote 
commander or select V Keystone in the 
Installation menu. 
2Use the V/v/B/b keys to set the value. The 
higher the value, narrower the top of the 
projected image. The lower the value, the 
narrower the bottom.
Since the Keystone adjustment is an electronic 
correction, the image may be deteriorated.
Displaying a pattern
You can display a pattern for adjusting the projected image or a grid pattern with the PATTERN 
key on the remote commander. Press the PATTERN key again to restore the previous image. 
You can use a grid pattern as a guide to write text or to draw lines and shapes on the whiteboard 
or blackboard without using a computer.
You cannot use this key when “Type A USB”, “Type B USB” or “Network” is selected as the input.
Automatically adjusts Phase, Pitch and Shift of projected image while a 
signal is input from a computer (APA (Auto Pixel Alignment))
Press the APA key on the remote commander. Press again to cancel adjusting during the setting.
You can also set APA in the Screen Menu (page 22). If Smart APA in the Function menu is set 
to “On”, executes APA automatically when a signal is input (page 25).
Note
Increase the number 
towards plus
Increase the number 
towards minus
Note 
						

							18Projecting an Image
1Press the ?/1 key on the unit or the remote commander.
The projector starts shutdown and turns off. If you press the ?/1 key within 10 seconds 
again, shutdown is cancelled.
2Unplug the AC power cord from the wall outlet.
To turn off without displaying confirmation message
Press and hold the ?/1 key on the unit for a few seconds (page 44).
ECO gauge
This gauge indicates the current effectiveness of the projector’s ECO function. (For details on 
the ECO function, see “ECO MODE key” (page 7) and “ECO” (page 27).) 
The leaf icons are displayed when the projector is shut down. The number of displayed icons 
varies according to how much energy is saved as a result of using the ECO function.
Turning Off the Power
ECO gauge 
						

							19Using a MENU
Adjustments and Settings Using a Menu
BAdjustments and Settings Using a Menu
Using a MENU
The menu displays used for the explanation below may be different depending on the model you are 
using.
1Press the MENU key to display the 
menu.
2Select the setting menu. 
Use the V/v key to select the setting 
menu then press the b key or ENTER 
key.
3Select the setting item.
Use the V/v key to select the setting 
menu then press the b key or ENTER 
key.
To return to the selection screen of the 
setting menu, press the B or RETURN 
key.
4Make the setting or adjustment for the 
selected item. 
The setting method varies, depending on 
the setting item.
If the next menu window is displayed, 
select the item according to the operations in step 3 and then press the 
ENTER key to register the setting.
To return to the selection screen of the 
setting items, press the B or RETURN 
key. You can press the RESET key to 
reset an item to its factory setting value 
to aid setting.
Using a pop-up menu
Press the V/v/B/b key to select an item.
A selected item takes effect 
immediately, except “Language”, which 
will take effect after you press the 
ENTER key.
Using the setting menu 
Press the V/v key to select the item. 
Press the ENTER key to register the 
setting and return to the previous screen.
Using the adjustment menu
To increase the value, press the V/b key 
and to decrease the number, press the 
v/B key. Press the ENTER key to 
register the setting and return to the 
previous screen.
5Press the MENU key to clear the 
menu.
The menu disappears automatically if no 
operation is performed.
Note
Picture Mode Standard
Reset
Contrast
Brightness
Color
Hue
Color Temp.
Sharpness
Expert Setting
:Sel :Set :Back
Picture
Low
Setting menu
80
50
50
50
5
Picture Mode Standard
Reset
Contrast
Brightness
Color
Hue
Color Temp.
Sharpness
Expert Setting
:Sel :Set :Back
Picture
Low
Setting items
RETURN
Picture Mode
Dynamic
Standard
:Back
:Sel
Cinema Game Blackboard Presentation
AdjustBack Contrast 
						

							20The Picture Menu
The Picture Menu
The Picture is used to adjust the picture for each input signal.
*1: When a computer signal is input, this option is available.
*2: The settings in the Picture return to their factory defaults, except for Picture Mode.
*3: When a video signal is input, this option is available.
*4: When the signal without color burst signal is input after selecting “Video” or “S-Video”, this 
option is unavailable.
*5: When an analog TV signal is input, this option may not available, depending on the color system.
*6: When “Picture Mode” is set to the item other than  “Presentation” or “Blackboard,” this option 
is available.
*7: When “Picture Mode” is set to “Blackboard,” this option is unavailable.Items Item descriptions
Picture ModeDynamic: Emphasizes the contrast to produce a dynamic and vivid picture.
Standard: Provides an image which is natural and well balanced.
Presentation
*1: Provides a bright image, suitable for presentations.
Blackboard: Provides an image suitable for displaying on a blackboard.
Game: Provides an image suitable for viewing games.
Cinema: Provides an image suitable for viewing movies.
Reset
*2Resets the factory setting.
Contrast The higher the value, the greater the contrast. The lower the value, the lower 
the contrast.
Brightness The higher the value, the brighter the picture. The lower the value, the darker 
the picture.
Color
*3 *4The higher the value, the greater the intensity. The lower the value, the lower 
the intensity.
Hue
*3 *4 *5The higher the value, the more greenish the picture becomes. The lower the 
value, the more reddish the picture becomes.
Color Temp.
*6High/Middle/Low: The higher the value, the more bluish the picture. The 
lower the value, the more reddish the picture.
Sharpness The higher the value, the sharper the picture. The lower the value, the softer 
the picture.
Expert Setting
Gamma 
Mode
*1 *7Graphics1: Gamma correction to make halftones brighter. This setting is 
suitable when projecting highly colorful images, such as photos, in a bright 
place.
Graphics2: Gamma correction to improve the reproduction of halftones. 
Highly colorful images, such as photos, can be reproduced in natural tones.
Text: Improves black and white contrast. Suitable for images with lots of text 
content.
Notes