Sony Projector VPL-EW130 User Manual

21The INSTALL SETTING Menu
Adjustments and Settings Using a Menu
The INSTALL SETTING Menu
The INSTALL SETTING menu is used for installing the projector.
*1: Since the Keystone adjustment is an electronic correction, the image may be deteriorated.
*2: When “High Altitude Mode” is set to “On,” the speed of the fan increases, and the fan noise 
becomes slightly louder.
*3: You will not be able to use the projector if you forget your password. If you call qualified Sony 
personnel because you have forgotten...

22The INFORMATION Menu
The INFORMATION Menu
The INFORMATION menu enables you to confirm various information on the projector, such 
as the total usage hours of a lamp.
*1: These items may not be displayed depending on the input signal.Items Item descriptions
Model Name Displays the model name.
Serial No. Displays the serial number.
fH
*1Displays the horizontal frequency of the current input signal.
fV
*1Displays the vertical frequency of the current input signal.
Signal type Displays the type of the...

23Indicators
Others
BOthers
Indicators
The indicators allow checking the status and notify you of abnormal operation of the projector.
If the projector exhibits abnormal status, address the problem in accordance with the table 
below.
?/1 key
LAMP/COVER indicator
StatusMeaning/Remedies
Lights in red The projector is in Standby mode.
Flashes in green  The projector is ready to operate after having been turned on. 
 The lamp cools after the projector is turned off.
Lights in green The projector’s power is...

24Messages List
Messages List
When any of the messages listed below appears on the projected image, address the problem in 
accordance with the table below.
MessageMeaning/RemedyPage
High temp.! Lamp off in 
1 min.Check the items below.
 Check to see if nothing is blocking the ventilation holes.
 Check to see if the air filter is not clogged.3, 29
Frequency is out of 
range!Change the output setting of the connected equipment to one 
for signals supported by the projector.33
Please check Input-A 
Signal...

25Troubleshooting
Others
Troubleshooting
Before asking to have the projector repaired, try to diagnose the problem, following the 
instructions below.
SymptomRemedyPage
The power is not turned 
on.Check if the AC power cord is firmly connected. –
When the “Panel Key Lock” is set to “On,” you cannot turn on 
the projector using the ?/1 key on the projector.19
If the lamp or lamp cover is not attached securely, the projector 
cannot be turned on.27
If the air filter or air filter cover is not attached...

26Troubleshooting
The image is not clear. Check if the projector is in focus. 12
The picture will not be clear if condensation has accumulated 
on the lens. In such a case, let the projector sit for about two 
hours with the power on.–
The image is noisy. Check if the connecting cable is connected to external 
equipment properly.7
No sound. Check that the connecting cables between the projector and 
external video or audio equipment are securely connected.7
Check if the output setting of connected...

27Replacing the Lamp
Others
Replacing the Lamp
Replace the lamp with a new one if a message displayed on the projected image or the LAMP/
COVER indicator notifies you to replace the lamp (pages 23, 24).
Use an LMP-E211 projector lamp (not supplied) for replacement.
 The lamp remains hot after the projector is 
turned off. If you touch the lamp, you may 
burn your finger. When you replace the 
lamp, wait for at least an hour after 
turning off the projector for the lamp to 
cool sufficiently.
 Do not...

28Replacing the Lamp
4Insert the new lamp all the way in until 
it is securely in place. Tighten the 
2 screws.
5Close the lamp cover and tighten the 
1 screw.
Be sure to install the lamp and Lamp cover 
securely as it was. If not, the projector 
cannot be turned on.
6Connect the AC power cord to a wall 
outlet and turn on the projector.
7Reset the lamp timer for notification of 
the next replacement time.
Select “Lamp Timer Reset” on the SET 
SETTING  menu then press the ENTER 
key. When a message...

29Cleaning the Air Filter
Others
Cleaning the Air Filter
When a message appears on the projected image, clean the air filter (page 24).
If the dust cannot be removed from the air filter even after cleaning, replace the air filter with 
a new one.
For details on a new air filter, consult with qualified Sony personnel.
If you neglect to clean the air filter, dust may accumulate, clogging it. As a result, the 
temperature may rise inside the unit, leading to a possible malfunction or fire.
1Turn off the...

30Specifications
Specifications
ItemDescription
ModelVPL-EW130
Projection system 3 LCD system
Display device Effective display 
size0.59-inch (15.0 mm), 3 plate, Aspect ratio 16:10
Effective picture 
elements3,072,000 pixels (1280 × 800 pixels, 3 plate panels)
Projection lens Zoom Manual zoom (approx.1.3 times)
Focus Manual
Light source High-pressure mercury lamp, 210 W type
Projected image 
size25 inches to 200 inches (0.635 m to 5.08 m)
Luminous flux 
(Brightness)3000 lm (when “Lamp Mode” is set to...