Sony Projector Srx R220 User Manual

21 Location and Function of Controls
Rear
aSTATUS MESSAGE window
Displays various messages.
For details on the messages, see page 22.
bStatus indicators
Combinations of the MAIN and LAMP indicators indicate 
the status of the projector as follows:
z: Lights    : Flashes    –: Goes out
cLamp adjustment window
The lamp adjustment screw is inside this window. Fine 
adjustment of the lamp position is necessary after 
replacing the lamp.
For adjustment, contact Qualified Sony Service Personnel.
dVentilation...

 22Messages
Messages
Various messages may be displayed in the STATUS MESSAGE window at the rear of the projector during operation.
Displayed messages are classified into “Error messages” and “Information messages.”
Error Messages
Error messages are classified into three types, described below, depending on the danger level.
If an error occurs, the message number and the message are displayed in the STATUS MESSAGE window.
ALERT : Danger level - High
Message number: ALERT_xx
WARNING: Danger level - Middle...

23 Messages
WARNING: Danger level – Middle
ALERT_08 BOARD ERROR Trouble with power of DST board
ALERT_09 BOARD ERROR Trouble with power of PR1 board
ALERT_10 BOARD ERROR Trouble with power of PR2 board
ALERT_11 BOARD ERROR Trouble with power of SY board
ALERT_12 BOARD DETACHED CN board disconnected
ALERT_13 BOARD DETACHED MX board disconnected
ALERT_14 BOARD DETACHED LPD board disconnected
ALERT_15 BOARD DETACHED CT board disconnected
ALERT_16 BOARD DETACHED DST board disconnected
ALERT_17 BOARD DETACHED...

 24Messages
 FAILURE: Danger level – Low
Information Messages
The message number is not displayed for information messages. Check the following if a message appears in the STATUS 
MESSAGE window.
WARN_22 DEVICE ERROR Failure of the peltier B control
WARN_23 CONNECTOR DETACHED The peltier R connector disconnected
WARN_24 CONNECTOR DETACHED The peltier G connector disconnected
WARN_25 CONNECTOR DETACHED The peltier B connector disconnected
WARN_26 DOUSER ERROR Trouble with the douser operation
WARN_27...

25 Messages
LAMP POWER – LIMIT Lamp power was automatically adjusted by correcting luminance 
deterioration, but the picture is not darker.
LOW REAL TIME CLOCK 
BATTERYThe RTC battery (BT200) for the SY board should be replaced.
LUMI VALUE + LIMIT Correction for luminance deterioration was made, but the picture is not 
brighter.
LUMI VALUE – LIMIT Correction for luminance deterioration was made, but the picture is not 
darker.
MessageMeaning 

 26Maintenance / Specifications
Maintenance
Some components of the projector are consumable parts 
over a long period of use.
To keep the projector working properly and to prolong its 
usable lifetime, have the projector inspected periodically. 
We recommend you make a maintenance contract for 
periodical inspection with us. For details on the contract, 
consult with Qualified Sony Service Personnel.
Specifications
Optical characteristics
Projection system
SXRD (Silicon X-tal Reflective Display)
3 panel...

27 Specifications
200 to 208/380 to 415 V AC, 50/60 Hz 
(three-phase lamp power)
Current consumption
SRX-R220: 11 to 5 A (single-phase main 
power) 
21/11 A (three-phase lamp power)
SRX-R210: 11 to 5 A (single-phase main 
power) 
13.5/7 A (three-phase lamp power)
Operating temperature
5°C to 35°C (41°F to 95°F)
Performance guarantee temperature
10°C to 30°C (50°F to 86°F)
Operating humidity
35% to 85% (no condensation)
Storage temperature
–20°C to +60°C (–4°F to +140°F)
Storage humidity
10% to 90%...

Sony Corporation
Printed in Japan