Sony Pmv F5 Manual

Using SxS Memory Cards31
Preparations
While recording (or standing by to record), you 
can check the remaining space for the SxS 
memory cards loaded in the card slots on the A/B 
slot media status/remaining space indication of 
the sub display (page 17) or viewfinder screen 
(page 20).
The available time for recording with the current 
video format (recording bit rate) is calculated 
according to the remaining space of each card and 
displayed in time units of minutes.
Note
A   icon appears if the...

Using an SD Card32
Preparations
You can store the setting value file of the camera 
on an SD card (optional). The stored file can be 
loaded from the SD card.
SDHC memory card* (Speed Class: 4 to 10, 
UHS is not compatible, Capacity: 2 GB to 32 GB)
SD memory card* (File system: FAT 16, 
Capacity: up to 2 GB)
* Indicated as “SD card” in these Operating Instructions.
1Open the cover of the card slot block 
(page 14).
2Insert the SD memory card into the slot 
with the SD label facing up.
The ACCESS lamp...

Using an AXS-R533
Preparations
You can record image/audio (RAW format) data 
to the AXS (Access Memory Card System) 
recorder AXS-R5 (optional) by connecting the 
AXS recorder to the camcorder.
Note
Attach/remove the AXS-R5 while the camcorder is 
turned off.
1Press the release button of the AXS-R5 
(1) to pop up the ejection lever, then 
raise the ejection lever (2).
2Insert the projection of the AXS-R5 into 
the slot on the rear of the camcorder 
(1), then lower the ejection lever (2).
Notes
 Before...

Using an AXS-R534
Preparations
Open the cover of the AXS-R5, press the 
EJECT button and remove the AXS 
memory card.
Note
Data integrity is not guaranteed if the power is turned off 
or a memory card is removed while it is being accessed. 
Data on the card may be destroyed. Be sure that its 
ACCESS lamp is lit in green or off when you turn off the 
power or remove a memory card.
Set “Shooting Mode” in “Base Setting” (page 90) 
to “Cine EI,” and “Main Operation” in “Base 
Setting” (page 90) to “RAW” of...

Using a USB Wireless LAN Module35
Preparations
To update the managerial file
If clips cannot be played back, updating the 
managerial file on the card may improve the 
situation. For this operation, use “Update Media” 
(page 85) of the Media menu.
You can make the Wi-Fi connection between the 
camcorder and a device such as a smartphone, 
tablet, etc., by attaching the supplied IFU-WLM3 
USB wireless LAN module.
Note
 The IFU-WLM3 USB Wireless LAN Module 
(supplied) may not be available in some...

Using a USB Wireless LAN Module36
Preparations
Note
Only one Wi-Fi device can be connected at a time.
To make a network setting
Change the “Basic Authentication” settings (page 
94) of the System menu as required.
For details about the menu settings and entering a 
character string, see “Setup Menu Operations” 
(page 56).
To make a connection
1Set “Wi-Fi” in “Wi-Fi” (page 94) of the 
System menu to “Enable.”
2Make a Wi-Fi connection by inputting 
the SSID and Password onto the device, 
or by using the...

Using a USB Wireless LAN Module37
Preparations
Playback screen
Cursor screen
Assign screenTablet
Main screen
 Wi-Fi connecting status (Connected/Disconnected)
 Status indication:
operating status, time data, audio level meter, clip 
name, recording format, media status/remaining space, 
battery remaining charge/DC IN voltage
 Assignable button indication:
Assignable buttons 1 to 4
 Recording settings indication:
S&Q FPS, Shutter, Color Temp., Sensitivity/Gain/
Exposure Index, Gamma, MLUT, Color Bars,...

Using a USB Wireless LAN Module38
Preparations
 Wi-Fi connecting status (Connected/Disconnected)
 Status indication
 Assignable button indication
 Cursor operation button, menu/status indication:
Up, Left, Set, Right, Down, Cancel/Back, Menu, 
Status
To display the Wi-Fi remote commander
The display size of the Wi-Fi remote commander 
changes according to the device screen size 
automatically.
1Make a Wi-Fi connection between the 
device and camcorder (page 36).
2Launch the browser and input http://...

Using a USB Wireless LAN Module39
Preparations
You can set/display the following items of the 
setup menu on the Wi-Fi remote display (tablet) 
(a: compatible, –: not compatible).
Notes
 When the setup menu is displayed on the Wi-Fi remote 
commander, you cannot set the setup menu items other 
than “Basic Authentication” and “Wi-Fi” of the 
System menu on the camcorder.
 When the setup menu is displayed on the Wi-Fi remote 
commander, you cannot change the settings on the sub 
display.
Camera menu...

Basic Operation Procedure40
Recording
Basic recording can be performed with the 
following procedures.
1Make sure that the necessary devices 
are attached to the camcorder and 
power is supplied to them.
2Load the memory card(s).
If you load two cards, recording is continued 
by automatically switching to the second 
card when the first card becomes full.
3Set the power switch (page 12) to the ON 
position.
The recording screen is displayed on the 
viewfinder screen.
4Press the REC button (page 11).
The...