Sony Nex 5 Service Manual

							A6CCCE74558B3E905AD2CEF677F08944E4F80AE9D638E1A7EC0B95815DA1F3ED
NEX-3A/3D/3K/5A/5D/5K/5CK/5H_L2
3-3
Assembly-20:Routing of Microphone Harness
(NEX-3A/3D/3K)
Microphone Cabinet (Upper) Assy
Insert the surplus part into
the hole as shown here. Route the harnesses under the
two ribs of Cabinet (Upper) Assy.
Cabinet (Upper) Assy
RL Block Assy
Note: Make sure that the PW Knobis turned to OFF position
when assembling Cabinet
(Upper) Assy to RL Block
Assy.
PW Knob
Assembly-21: Assemble Cabinet (Upper) Assy
(NEX-3A/3D/3K)
Assembly-22: Radiation Sheet (CN) (210)
putting position
(NEX-3A/3D/3K)
CN-439 Complete Board
FP-1246
Flexible Board Radiation Sheet
(CN) (210)
Within 1.0mm
Without running on the
reinforcement board
Within 1.0mm
Cabinet (Front)
IM Adjust Washer B
IM Adjust Washer A
IM Adjust Washer C
Assembly-23:IM Adjust Washer (A, B, C)
putting position
Assembly-25: BT Slider Sheet (front) putting position
(NEX-5A/5D/5K/5CK/5H)
BT Slider Sheet (front)Rib edge (horizontal):
¶0.5mm
Rib edge (vertical):
¶0.5mm
Lib edge (vertical):
¶0.5mm
MB N Plate SP
Assembly-27: Apply grease on MB N Plate SP
GG-85
(J-6082-626-A)
BT Slider Sheet
(horizontal)
Cabinet (Front)
Assembly-26: BT Slider Sheet (horizontal)
putting position
(NEX-5A/5D/5K/5CK/5H)
From edge
(vertical):
¶1.0mm
From edge
(horizontal):
¶1.0mm
J-6082-735-A
MB Mask Sheet
Note:
There should not be any misalignment when attaching
MB Mask Sheet.
MB Mask
Sheet Tape
Cabinet (Front)
Assembly-24:Method of attachment of MB Mask Sheet
The changed portions from
Ver.1.1 are shown in blue.
Ver.1.2 2010.07 
						

							A6CCCE74558B3E905AD2CEF677F08944E4F80AE9D638E1A7EC0B95815DA1F3ED
NEX-3A/3D/3K/5A/5D/5K/5CK/5H_L2
3-4
Hold here
Assembly-28:MB N Contact Unit holding position
MB N Contact Unit
Insert IS-075 Flexible Board into the connector on
IM Imager Unit 14M, then lock the connector.
Assemble Heat Sink and IM Imager Unit 14M.
Note: IS-075 Flexible Board can not be inserted after assembling Heat Sink.
Heat Sink
IM Imager Unit 14M
IS-075 Flexible Board
Assembly-30: PriorInsertion of IS-075 Flexible Board
(NEX-3A/3D/3K)
Radiation Sheet (IS)
Heat Sink
Without running off the
edge of the hole. Without running on the
edge of Heat Sink.
Assembly-31:
RadiationSheet (IS) putting position
SY-258 Complete Board
CN-439 Complete Board
Put the surplus part of the
shutter flexible board under
SY-258 Complete Board.
Assembly-32: How to handle the Shutter Flexible Board
(NEX-3A/3D/3K)
Assembly-29: Note when assembling Heat Sink
Align with the positioning hole.
Heat Sink
CN-439
Complete Board
LC Connector
Insulating Sheet BT Frame Assy
Within 0.5mm Within 0.5mm
Assembly-33:
LC ConnectorInsulating Sheet
putting position
Assembly-34: Tape AS (210) putting position
(NEX-5A/5D/5K/5CK/5H)
Tape AS (210)
Without protruding
from the rib top surface.
Without running off
the mask sheet. Without running on this boss.
Assembly-35:
Method of attachment of LC Flexible
Insulating Sheet
(NEX-3A/3D/3K)
Bend the LC Flexible Insulating Sheet along
the curve of BT-063 Flexible Board.
LC Flexible
Insulating Sheet ¶1.0mm
The changed portions from
Ver.1.1 are shown in blue.
Ver.1.2 2010.07 
						

							A6CCCE74558B3E905AD2CEF677F08944E4F80AE9D638E1A7EC0B95815DA1F3ED
NEX-3A/3D/3K/5A/5D/5K/5CK/5H_L2
3-5E
3-2.
 CLEANING  PROCEDURE  OF  OLPF

If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip). The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.

If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).

1. Put the two cleaning cloths on a tray like below.
 1 Souse the one cleaning cloth in ethyl alcohl.
 2 Put the other cleaning cloth on a tray as it is dry.
2.
 Dab the tip of CCD cleaning jig at the cleaning cloth of  1 5 or 6 times.
 * Do not slide the tip from right to left or up and down while dabbing.
3.
 Dab the tip of CCD cleaning jig at the cleaning cloth of  2 5 or 6 times.
 * Do not slide from right to left or up and down while dabbing.
4.
 Wait until the tip will be dried completely. 
1.
 Clean up the tip of CCD cleaning jig.
2.
 Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 * Do not slide from right to left or up and down while dabbing.
3.
 Repeat “3” several times to clean up.
4.
 According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip) Protection Sheet
1
Souse the cleaning
cloth in ethyl alcohol.
2 The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A) Cut
EE3310