Sony Kdl 32e5500 Operating Instructions

							21 GB
C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\0WAT.fmmasterpage:Left
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Watching TV
Using the Favourite List
Analogue FavouritesThe Favourite feature lets you select 
programmes from a list of up to 16 favourite 
channels that you specify.
1In analogue mode, press  .
2Perform the desired operation as shown in 
the following table or displayed on the 
screen.
Digital FavouritesYou can specify up to four of your favourite 
channel lists.
1In digital mode, press  .
2Perform the desired operation as shown in 
the following table or displayed on the 
screen.
Analogue Favourite List
ToDo this
Watch a channel Press  .
Turn off the Favourite list Press  .
Add a current channel to the 
Favourite listPress F/f to select “Add to Favourites”, then press  .
Remove a channel from the Favourite 
list
1Press F/f to select “Edit Favourites”, then press  .
The “Favourite Set-up” screen appears.
2Press F/f to select the channel number, then press  .
3Press F/f to select “– –”, then press  .
Digital Favourite List
ToDo this
Add or remove channels in a 
Favourite list1Press the blue button.
Go to step 2 when you add channels for the first time or the 
Favourite list is empty.
2Press the yellow button to select the Favourite list to edit.
3Press F/f/G/g to select the channel to add or remove, then press 
.
Watch a channel
1Press the yellow button to select a Favourite list.
2Press F/f to select a channel, then press  .
Remove all channels from a 
Favourite list
1Press the blue button.
2Press the yellow button to select the Favourite list to edit.
3Press the blue button.
4Press G/g to select “Yes”, then press  .
010COV.book  Page 21  Tuesday, January 20, 2009  5:15 PM
 
						

							
C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\8OPT.fmmasterpage:Left
22 GB
KDL-52/46/40/37/32V5500 x-xxx-xxx-xx(x)
Using Optional Equipment
Connecting Optional Equipment
You can connect a wide range of optional equipment to your TV.
Connecting audio-video equipment (quality order, high to low)
Connect toConnect withDescription
5 , 9 , qa
HDMI IN 1, 2, 3, 
or 4 HDMI cable
Digital video and audio signals  are input from the connected 
equipment.
In addition, when you conn ect the equipment that is 
compatible with Control for  HDMI, communication with the 
connected equipment is supported (page 40).
If the equipment has a DVI so cket/jack, connect the DVI 
socket/jack to the HDMI IN 1 socket/jack through a DVI - 
HDMI adaptor interface (not supplied), and connect the 
equipment’s audio out sockets/ja cks to the audio in sockets/
jacks in the HDMI IN 1 sockets/jacks.
~
• Be sure to use only an auth orized HDMI cable bearing the 
HDMI logo. We recommend that you use a Sony HDMI 
cable (high speed type).
• When connecting an audio system  that is compatible with 
Control for HDMI, be sure to also connect it to the 
DIGITAL AUDIO OUT (OPTICAL) socket/jack.
qs
qd 0
qa
8
9 7
12 354
6
070OPT.fm  Page 22  Friday,  January 30, 2009  5:41 PM
 
						

							23 GB
C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\8OPT.fmmasterpage:Left
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Using Optional Equipment
3 / 
COMPONENT INComponent video 
cable, audio cable
2 /AV1, 
// AV2SCART cableWhen you connect a decoder, the TV tuner outputs scrambled 
signals to the decoder, and the decoder unscrambles the 
signals before outputting them.
qs AV3, and 
AV3Composite video 
cableWhen connecting a mono equipment, connect to the  AV3 
L socket.
Connecting audio/portable equipment
Connect toConnect withDescription
1 Audio cableYou can listen to TV sound on the connected Hi-Fi audio 
equipment.
4 DIGITAL 
AUDIO OUT 
(OPTICAL)Optical audio 
cable
8 USB USB cableYou can enjoy photo/music/video files stored in a Sony 
digital still camera or camcorder (page 25).
Connecting other equipment
Connect toConnect withDescription
6  / PC IN PC cable with 
ferrites, audio 
cableIt is recommended to use a PC cable with ferrites, such as the 
“Connector, D-sub 15” (ref. 1-793-504-11, available in Sony 
Service Centre), or an equivalent.
7 LAN LAN cableYou can enjoy contents stored in DLNA-compatible devices 
via a network (page 28).
0 CAM 
(Conditional 
Access Module)Provides access to pay TV services. For details, refer to the 
instruction manual supplied with your CAM.
To use the CAM, remove the “dummy” card from the CAM 
slot, then turn off the TV and insert your CAM card into the 
slot. When you are not using the CAM, we recommend that 
you keep the “dummy” card in the CAM slot.
~
• CAM is not supported in some countries/areas. Check with 
your authorised dealer.
qd i HeadphonesYou can listen to TV sound through headphones.
Connect toConnect withDescription
010COV.book  Page 23  Tuesday, January 20, 2009  5:15 PM
 
						

							C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\8OPT.fmmasterpage:Left
24 GB
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Viewing Pictures from 
Connected Equipment
Turn on the connected equipment, then 
perform the following operation.
For equipment connected to the scart 
sockets using a fully-wired 21-pin scart lead
Start playback on the connected equipment.
The picture from the connected equipment 
appears on the screen.
For an auto-tuned VCR
In analogue mode, press PROG +/– or the 
number buttons, to select the video channel.
To view two pictures simultaneously 
– PAP (Picture and Picture)
You can view two pictures (external input and 
TV programme) on the screen simultaneously.
~
• This function is not available for a PC input.
1Press OPTIONS.
2Press F/f to select “PAP”, then press  .
The picture from the connected equipment 
is displayed on the left, and the TV 
programme is displayed on the right.
3Press the number buttons or PROG +/– to 
select the TV channel.
To return to single picture mode
Press  RETURN.To view two pictures simultaneously 
– PIP (Picture in Picture)
You can view two pictures (external input and 
TV programme) on the screen simultaneously.
1Press OPTIONS.
2Press F/f to select “PIP”, then press  .
The picture from the connected PC is 
displayed in full size, and the TV 
programme is displayed in the small 
screen.
You can use F/f to change the position of 
the TV programme screen.
3Press the number buttons or PROG +/– to 
select a TV channel.
To return to single picture mode
Press  RETURN.
z
• You can switch the audible picture by pressing G/
g.
1Press .
2Press F/f to select 
the desired input 
source, then press  .
010COV.book  Page 24  Tuesday, January 20, 2009  5:15 PM
 
						

							25 GB
C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\8OPT.fmmasterpage:Left
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Using Optional Equipment
Playing back Photo/Music/
Video via USB
You can enjoy photo/music/video files stored 
in a Sony digital still camera or camcorder 
through a USB cable or USB storage device on 
your TV.
1Connect a supported USB device to the 
TV.
2Press HOME.
3Press G/g to select “Photo”, “Music”, or 
“Video”.
4Press F/f to select a USB device, then 
press .
The file or folder list appears.
To display a thumbnail list, press the 
yellow button while the list is displayed.
5Press F/f to select a file or folder, then 
press .
When you select a folder, select a file, 
then press  .
Playback starts.
Photo Playback Auto Start
The TV automatically starts photo playback 
when the TV is turned on and a digital still 
camera or other device storing photo files is 
connected to the USB port then turned on 
(page 39).
~
• While the TV is accessing the data on the USB 
device, observe the following:
– Do not turn off the TV or connected USB 
device.
– Do not disconnect the USB cable.
– Do not remove the USB device.
The data on the USB device may be damaged.
• Sony will not be held liable for any damage to, or 
loss of, data on the recording media due to a 
malfunction of any connected devices or the TV.
• Playback does not start automatically if the TV is 
turned on after connecting the digital still camera 
or other device to the USB port.
• You can register the background music to be 
played during a slideshow using   Photo by 
pressing OPTIONS, then select “Add to 
Slideshow” while playing back music.
• USB playback is supported for the following 
photo file formats:
–  JPEG (JPEG format files with the extension 
“.jpg” and conforming to DCF 2.0 or Exif 2.21)– RAW (ARW/ARW 2.0 format files with the 
extension “.arw”. For preview only.)
• USB playback is supported for the following 
music file format:
– MP3 (files with the extension “.mp3” that have 
not been copyrighted)
• USB playback is supported for the following 
video file format:
– MPEG1 (files with the extension “.mpg”)
• The file name and folder name support only 
English.
• When you connect a Sony digital still camera, set 
the camera’s USB connection mode to Auto or 
“Mass Storage”. For more information about USB 
connection mode, refer to the instructions supplied 
with your digital camera.
• Check the website below for updated information 
about compatible USB devices.
http://support.sony-europe.com/TV/compatibility/
To display a photograph 
— Picture Frame
You can display a photograph on the screen 
for a selected period of time. After that period, 
the TV automatically switches itself into 
standby mode.
1Select a photograph.
You can select a photograph from the 
connected USB device or preset picture 
folder. For details on selecting a 
photograph (page 25).
2Press OPTIONS while the selected 
photograph is displayed, then press F/f to 
select “Picture Frame Image” and press 
.
3Press  RETURN repeatedly to return 
to the Home Menu.
4Press G/g to select “Photo”, then select 
“Picture Frame” and press  .
The TV is switched to Picture Frame 
mode, and the selected photograph is 
displayed on the screen.
To set the duration of displaying a 
photograph
Press OPTIONS, then select “Duration” 
and press  . Then, select the duration, 
and press  .
The counter appears on the screen.
To return to the XMB™
Press  RETURN.
(Continued)
010COV.book  Page 25  Tuesday, January 20, 2009  5:15 PM
 
						

							C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\8OPT.fmmasterpage:Left
26 GB
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
~
• If the photograph is selected from a USB device, it 
must remain connected to the TV.
• If “Sleep Timer” is activated, the TV 
automatically will switch into standby mode.
To display a photograph with the 
location on the map
When using a digital still camera with GPS 
function, it is possible to display a photograph 
with a map of the location where the 
photograph was taken using a function of GPS 
for recording longitude and latitude. Because 
map information is downloaded from the 
Internet online map service, the network 
connection must be required and the TV has to 
be connected to the network (page 28).
1Select a photograph (page 25).
2Press the green/red buttons to zoom in/out 
on the map.
To change the display position of the map 
on the TV screen, press the blue button 
repeatedly.
~
• Because the Internet online map service is 
provided by a third party, service may be changed 
or terminated without prior notification to the 
user.
• The position indicated on the map may differ 
depending on the digital still camera.
• Only a large-scale map that cannot be zoomed in 
or out is displayed if the TV is not connected to 
the Internet or the Internet online map service is 
terminated. 
z
• A map can be displayed in the case of 
photograph’s Exif data includes a date 
information, and the associated longitude and 
latitude information (“Log files”) has been 
recorded using a Sony GPS unit. Follow the 
procedure described below.
1Connect the GPS unit to the USB port.
2Press HOME.
3Press G/g to select “Photo”.
4Press F/f to select the GPS unit, then 
press 
.
5Select the following items using F/f, then 
set them using G/g.
–Time Zone
–DST
6Select “OK”, then press .
The GPS log files are loaded.
7Disconnect the GPS unit and connect the 
device on which the photograph is stored.
8Select a photograph (page 25).
9Press the green/red buttons to zoom in/out 
on the map.
010COV.book  Page 26  Tuesday, January 20, 2009  5:15 PM
 
						

							27 GB
C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\8OPT.fmmasterpage:Left
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Using Optional Equipment
Using BRAVIA Sync with 
Control for HDMI
The Control for HDMI function enables the 
TV to communicate with the connected 
equipment that is compatible with the 
function, using HDMI CEC (Consumer 
Electronics Control).
For example, by connecting Sony equipment 
that is compatible with Control for HDMI 
(with HDMI cables), you can control them 
together.
Be sure to connect the equipment correctly, 
and make the necessary settings.
Control for HDMI
• Automatically turns the connected 
equipment off when you switch the TV to 
standby mode using the remote.
• Automatically turns the TV on and 
switches the input to the connected 
equipment when the equipment starts to 
play.
• If you turn on a connected audio system 
while the TV is on, the sound output 
switches from the TV speaker to the audio 
system.
• Adjusts the volume (2 +/–) and mutes the 
sound (%) of a connected audio system.
• You can operate the connected Sony 
equipment that has the BRAVIA Sync logo 
by the TV remote by pressing:
–m/N/X/M/x to operate the connected 
equipment directly.
–SYNC MENU to display the menu of the connected 
HDMI equipment on the screen. 
After displaying the menu, you can operate the 
menu screen by using F/f/G/g,  , colour buttons, 
and 
 RETURN.
–OPTIONS to display “Device Control”, then select 
options from “Options” and “Content List” to 
operate the equipment.
– Refer to the instruction manual of the equipment for 
available control.
• If “Control for HDMI” of the TV is set to 
“On”, “Control for HDMI” of the 
connected equipment is also automatically 
switched to “On”.To connect the equipment that is 
compatible with Control for HDMI
Connect the compatible equipment and the TV 
with an HDMI cable. When connecting an 
audio system, be sure to also connect the 
DIGITAL AUDIO OUT (OPTICAL) jack of 
the TV and the audio system using an optical 
audio cable (page 22).
To make the Control for HDMI settings
The Control for HDMI settings must be set on 
both the TV side and connected equipment 
side. See “HDMI Set-up” (page 40) for the TV 
side settings. For settings on the connected 
equipment, refer to the operating instructions 
for that equipment.
010COV.book  Page 27  Tuesday, January 20, 2009  5:15 PM
 
						

							C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\NET.fmmasterpage:Left
28 GB
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Using Home Network Features
With this TV, you can enjoy contents stored in 
DLNA-compatible devices on the home 
network.
Devices that store and provide contents, such 
as photo/music/video files, are called 
“Server”. The TV receives the photo/music/
video files from the server via the network, 
and you can enjoy them on the TV even in 
other rooms.
To enjoy the home network, a DLNA-
compatible device (VAIO, Cyber-shot, etc.) is 
necessary as a server.
In addition, when you connect your TV to the 
Internet, you can enjoy displaying a 
photograph that shows its location on the map 
(page 26), or enjoy AppliCast while 
watching a TV programme (page 29).
~
• You will need to contract with an Internet service 
provider to connect to the Internet.
Connecting to the Network
Network cable (not supplied) Broadband router
DSL modem/
Cable modem To network devices
Internet TV
Network 
cable 
(not 
supplied)
010COV.book  Page 28  Tuesday, January 20, 2009  5:15 PM
 
						

							29 GB
C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\NET.fmmasterpage:Left
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Using Home Network Features
Enjoying AppliCast
While watching TV, you can display variety of 
information on the edge of TV screen by using 
Widgets (i.e. mini-applications).
Many Widgets retrieve information from the 
Internet.
To Use Widgets
Widgets can be displayed by selecting from 
the Home Menu. While the Widget is 
displayed, you can add to your Widget list so 
that it would be registered to be automatically 
displayed next time when you launch 
AppliCast. Some Widgets allow you to save 
settings to provide you with the preferred 
information.
1Press HOME.
2Press G/g to select Network. 
3Press F/f to select the desired Widget to 
be displayed or simply select AppliCast 
icon to display your preferred list of 
Widgets.
4Follow the instruction on the Widget.
To return to single picture mode
Press  RETURN.
To Add or remove Widgets in AppliCast
You can add to or remove from the Widget 
list.
From Widget:
5While you are displaying the Widget, 
press OPTIONS.
6Select Add to AppliCast or Remove 
from AppliCast.
Up to 30 Widgets can be registered in 
AppliCast.
From Network in the Home Menu:
7Follow STEP1-2 above.
8Press F/f to select the desired Widget, 
then press OPTIONS.
9Follow STEP6.
z
• There are three Widgets already in the set that 
dont require internet connection. They are How 
to use AppliCast, Analogue Clock, and 
Calendar.• AppliCast Widgets stored in the USB Mass 
Storage Device connected to BRAVIA. The 
Widget icons should appear under USB icon under 
Network in the Home Menu.
~
•  MAC address and IP address are transmitted 
automatically from the TV to servers while 
internet connection is available.
The servers are under the control of Sony and 
MAC address will never be transmitted to the 
servers controlled by the other parties.
• Widgets may be changed or terminated without 
prior notification to the user.
(Continued)
010COV.book  Page 29  Tuesday, January 20, 2009  5:15 PM
 
						

							C:\Documents and Settings\Dolors\Mis documentos\€9\EX2L_CORREC 
PARAL\11_UK_EX2L\NET.fmmasterpage:Left
30 GB
KDL-52/46/40/37/32V5500
x-xxx-xxx-xx(x)
Enjoying Photo/Music/
Video Files via the Network
You can enjoy photo/music/video files on the 
server easily by selecting an icon on the Home 
Menu of the TV.
1Press HOME.
2Press G/g to select “Photo”, “Music”, or 
“Video”.
3Press F/f to select a server, then press  .
The file or folder list appears.
To display the thumbnail list, press the 
yellow button while the list is displayed.
When the server cannot be found
See “Checking the Network Connection” 
(page 31) and “Adjusting the Server 
Display Settings” (page 31).
4Press F/f to select a file or folder, then 
press .
When you select a folder, select a file, 
then press  .
Playback starts.
z
• A map can be displayed with a photograph in the 
case of longitude and latitude information has 
been recorded to photograph’s Exif data 
(page 26).
~
• Depending on the network device, it may be 
necessary to register the TV with the network 
device.
• Picture quality may appear coarse when using   
Photo because images may be enlarged depending 
on the file. Also, images may not fill the entire 
screen depending on the image size and aspect 
ratio.
• Some photo files may take some time to be 
displayed when using   Photo.
• To play files that are received from a network 
device, they need to conform to one of the 
following file formats. 
– Still images: JPEG format
– Music: MP3 format or linear PCM format
– Video: The following file formats stored on the 
sever: AVCHD, HDV, MPEG2-PS (which in 
some cases may not be able to be played)
Depending on the network device, the file format 
may be converted before transfer. In such cases, 
the file format resulting after conversion is used 
for playback. For details, refer to the instruction manual for the network device being used.
Even files conforming to one of the file formats 
given above cannot be played in some cases.
• The file name and folder name support only 
English.
To enjoy photographs, music and 
videos on the TV screen by operating 
devices
– Renderer
Renderer is a feature for playing photo, music 
and video files stored in network devices 
(digital still cameras, mobile phones, etc.) on 
the TV by operating the controller device in 
question. To use this feature, a renderer-
compatible device such as a digital still camera 
or mobile phone is required as the controller. 
Refer as well to the instruction manual 
supplied with the controller.
1Set “Renderer Function”, “Renderer 
Access Control” and “Renderer Set-up” in 
“Network Settings” if necessary 
(page 44).
2Play the file selected using the controller 
on the TV.
The file is played on the TV over the 
connected network.
Use the controller or the TV’s remote to 
perform operations during playback.
~
• You can register the background music to be 
played during a slideshow using   Photo. While 
playing back music, press OPTIONS, then select 
“Add to Slideshow”.
010COV.book  Page 30  Tuesday, January 20, 2009  5:15 PM