Sony F 35 User Manual

81Menu List
  Chapter 4   Menu Configuration and Detailed Settings

Adjusting the color 
components without 
affecting the black 
and white 
componentsP11
[ - - ]R-G 0–99 to +99
R-B 0–99 to +99
G-R 0–99 to +99
G-B 0–99 to +99
B-R 0–99 to +99
B-G 0–99 to +99
MATRIX OFF ON, OFF
PRESET - - ON, OFF, (OFF), - - Invalid when MATRIX is OFF 
(- - indication)
(OFF): Fixed to OFF when 
MATRIX is ON with 
COLOR SPACE set to S-
GAMUT or DCDM REF PJ
- - SMPTE-240M, ITU-709, 
SMPTE-WIDE, NTSC, 
EBU, - -Invalid when...

82Menu List
  Chapter 4   Menu Configuration and Detailed Settings

Adjusting the 
shutter while 
observing the 
shutter angles and 
speedsP13
[P03]
(U20)SHUTTEROFFON, OFFSetting to ON displays the 
current shutter values in the 
[deg] and [sec] columns.
[deg]: Shutter angle (360.0 to 
4.3)
[sec]: Shutter speed obtained 
according to the angle in  
[deg] and the FRAME 
RATE value
STEPTo change the shutter value in 
Step mode
CONTINUOUSTo change the shutter value in 
Continuous mode
STEP ASSIGN
ADDExecute...

83Menu List
  Chapter 4   Menu Configuration and Detailed Settings
Noise Suppression
This function you can enable on the PAINT menu  page effectively suppresses noise components 
while maintaining fine edge components of a subject.
As the noise suppression function of this camera employs a 
system to extract and depress noise within a frame, it also 
shows strong characteristics for movement of a subject 
compared with noise reduction that uses frame correlation.
You can select from among 4 effect...

84Menu List
  Chapter 4   Menu Configuration and Detailed Settings
4-3-3 MAINTENANCE Menu
The markings [M01] to [M12] in the No. column indicate the page numbers in Cine mode.
The pages marked with [ - - ] in the No. column are not displayed in Cine mode.
: Valid in Custom mode only
: Valid in both Cine and Custom modes
Execute by ENTER. : Execute by pushing on the MENU SEL/ENTER dial.
Note
MAINTENANCE menu
Page title & 
purposeNo.ItemDefaultSettingsRemarks

Setting the basic 
operation modeM01...

85Menu List
  Chapter 4   Menu Configuration and Detailed Settings

Adjusting the 
shading of white 
levelM03
[ - - ] V SAW[R] [G] [B]
000–99 to +99R, G, and B values can be 
independently set.
V SAW, H SAW: To 
vertically or horizontally 
adjust the slope of 
shading compensation
V PARA, H PARA: To 
vertically or horizontally 
adjust the irregularity of 
shading compensation V PARA 0 0 0–99 to +99
H SAW 0 0 0–99 to +99
H PARA 0 0 0–99 to +99
WHITE 0 0 0–99 to +99
AUTO WHITE 
SHADINGExecute by ENTER....

86Menu List
  Chapter 4   Menu Configuration and Detailed Settings

Selecting the IF BOX 
output SDI channels 
to which the 
microphone inputs 
are added and 
setting the signal 
delay compensationM06
[M02]CAMERA MIC CH 
SELECT
IF BOXCH5/6CH1/2, CH5/6Note
The microphone inputs 
added to SDI signals sent 
to the SRW-1 directly 
docked on the camera or 
optically connected to the 
camera via the CA-F101 
are fixed to CH5/6.
DELAY COMPONON, OFFON: The audio delay is 
automatically 
compensated according 
to...

87Menu List
  Chapter 4   Menu Configuration and Detailed Settings

Setting the voltage 
values to trigger 
alarm indicationsM10
[M06]DC IN (24 V)
TYPEAC ADPBATT1, BATT2, AC ADPBATT1/BATT2: Batteries
AC ADP: AC adaptor
NEAR END22.2 V0.1 to 30.0 VFixed to the default value 
for AC ADP
END21.6 V0 to 29.9 VFixed to the default value 
for AC ADP
DC IN (12 V)
TYPEAC ADPBATT1, BATT2, AC ADPBATT1/BATT2: Batteries
AC ADP: AC adaptor
NEAR END11.1 V11.0 to 17.0 VFixed to the default value 
for AC ADP
END10.8 V10.5...

88Menu List
  Chapter 4   Menu Configuration and Detailed Settings

Setting various 
subsidiary functionsM14
[M10]
(U21)FAN MODEAU TO1AU TO 1,  AU TO2 ,  MI N ,  
MAXTo select the operation 
modes of the fans
AUTO1: Automatically 
controlled according to 
the internal temperature 
and in a quiet condition 
during recording
AUTO2: Normally 
controlled in MIN mode 
and in a quieter 
condition during 
recording (only for a 
short recording under 
ordinary ambient 
temperature)
MIN: The quietest fan...

89Menu List
  Chapter 4   Menu Configuration and Detailed Settings

Setting various 
subsidiary functionsM15
[M11]DATE TYPE5 M/D/Y1 Y/Mn/D
2 Mn/D
3 D/M/Y
4 D/M
5 M/D/Y
6 M/DTo select the date display 
mode
Y:  Yea r
Mn: Month (numeric)
M: Month (character string)
D: Day
V DTL CREATION
 1)Y NAM, G, R+G, Y To specify from which 
signal the vertical detail 
volume is to be created
NAM: The highest signal 
among R, G, and B
G: G signal
R+G: Additional value of 
the R signal and G 
signal
Y: Y signal
DTL H/V...

90Menu List
  Chapter 4   Menu Configuration and Detailed Settings
1) Not displayed in Cine mode
4-3-4 NETWORK Menu
The NETWORK menu items can be set in both Cine and 
Custom modes.For details, see “ Parameter Settings” (page 111).

Setting the color 
space of HDVF-
C30WRM16
[M12]VF COLOR SPACEAU TOAU TO, S T DValid only with the HDVF-
C30WR viewfinder 
connected
AUTO: To synchronize with 
the camara’s color 
space
STD: To fix to F900
MAINTENANCE menu
Page title & 
purposeNo.ItemDefaultSettingsRemarks...