Sony Dav D150 Operating Instructions

							11GB
PREPARATION
Connections (Continued)
Radio Aerial Connections
Connect the supplied FM/AM antennas for radio listen-
ing.
1
Connect the AM loop antenna to the AM antenna
connectors.
2
Connect the FM wire antenna to the FM antenna
connectors.
Notes
zTo prevent noise pickup, keep the AM loop antenna
away from the DVD/VCR Receiver and other compo-
nents.
zBe sure to fully extend the FM wire antenna.
zAfter connecting the FM wire antenna, keep it as hori-
zontal as possible.
Accessory Audio/Video (A/V)
Connections to DVD/VCR Receiver
Connect theAV3 INjacks on the DVD/VCR Receiver to
the audio/video out jacks on your accessory compo-
nent, using optional audio/video cables.
Digital Device Connections
Connect the OPTICAL IN jacks on the DVD/VCR
Receiver to the digital audio out (optical) jacks on your
digital device (Game device, Digital Set Top Box, etc.),
using optional optical audio cable.
To select source of DVD/VCR Receiver to OPTICAL IN,
press INPUT SELECT repeatedly on the remote control
until “AV3 OPT” appears in the display window.
Notes
zIf the audio format of the digital output does not
match the capabilities of your DVD/VCR Receiver, the
DVD/VCR Receiver will produce a strong, distorted
sound or no sound at all. 
zThe Optical input function is available only when the
other unit’s Sampling Frequency is 32 - 48kHz.
 
						

							12GB
Connections (Continued)
Speaker System Connections
Connect the speakers using the supplied speaker cords
by matching the colors of the terminals and those of the
cords. To obtain the best possible surround sound,
adjust the speaker parameters (distance, level, etc.).
Notes
zBe sure to match the speaker cord to the appropriate
terminal on the components: 3to 3and #to #. If
the cords are reversed, the sound will be distorted
and lack bass.
zIf you use front speakers with low maximum input rat-
ing, adjust the volume carefully to avoid excessive
volume output to the speakers.
zDo not disassemble the front covers of supplied speakers.
Speaker Positioning
For a normal setup use 6 speakers (2 front speakers,
center speaker, 2 rear speakers and subwoofer). 
•Front Speakers
Based on your listening position, set up the speakers
at equal distance. And by hearing position, set up an
interval between speakers of 45 degree.
•Center Speaker
It is ideal that the center speakers and front speakers
are same height. But normally place it above or below
the television as shown below.
•Rear Speakers
Place the rear surround speakers to the left and right
behind the primary listening area. These speakers
recreate sound motion and atmosphere required for
surround playback. For best results, do not install the
rear speakers too far behind the listening position,
install them at or above the level of the listener’s ears.
It is also effective to direct the rear speakers towards
a wall or ceiling to further disperse the sound.
In the case of a smaller room size, if the audience is
near to the rear wall set the rear speakers opposite
each other, and set the rear speakers 60 - 90 cm
above the listener’s ears.
•Subwoofer
This can be placed in any front position.
Note
Speaker stand is optional.
Attaching the foot pads
To prevent speaker vibration or
movement while listening, attach the
supplied foot pads to the speaker, as
shown.
Attaching the color labels
Attach the color labels onto the rear
panel of the speakers before con-
necting the speakers.
Front Speaker
      (Right)Front Speaker
        (Left)Center
Speaker
Rear speaker
(Left surround)
SubwooferRear speaker
(Right surround)
Center Speaker
Front
Speaker
(Left)
Speaker Positioning Example
Rear
Speaker
(Left)Rear
Speaker
(Right) Front
Speaker
(Right) Subwoofer
Be sure to attach the ferrite core to
the speaker cables (for connecting to
this unit).
This ferrite core can reduce noises. 
How to attach the ferrite core.
1Push the stopper [a] of the ferrite core
to open.
2Wind the Center and Subwoofer Speaker
cables once on the ferrite core. 
Pass the others straight on the ferrite core.
3Close the ferrite core until it clicks.
About Ferrite Core
1
2
3
Foot pads
FRONT  L
Color labels
 
						

							PREPARATION
13GB
Selecting the Input/Output Source
Follow these guidelines to select and switch among the
various DVD/VCR Receiver input and output sources: 
•DVD
To view output from the DVD deck:
Press DVD on the remote or DVD/VIDEO on the on
the front panel until the DVD indicator on the front
panel lights and output from the DVD deck is viewed
on the TV screen.
•VIDEO
To view output from the VIDEO deck:
Press VIDEO on the remote or DVD/VIDEO on the
front panel until the VIDEO indicator on the front
panel lights and output from the VIDEO deck is
viewed on the TV screen.
•TUNER FM/AM
To listen to AM/FM radio broadcasts:
Press TUNER FM/AM on the remote to toggle
between AM and FM radio. Press TUNER FM/AM to
toggle between AM and FM radio. The selected fre-
quency appears in the display window.
•INPUT SELECT
To listen and view to an audio source connected
to the EURO AV1:
Press INPUT SELECT on the remote control once.
The “AV1” appears in the display window and TV
screen. Audio and Video will come from an external
source connected to the EURO AV1 (for rear panel).
To listen and view to an audio source connected
to the EURO AV2:
Press INPUT SELECT on the remote control a sec-
ond time. The “AV2” appears in the display window
and TV screen. Audio and Video will come from an
external source connected to the EURO AV2 (for rear
panel).
To listen to an audio source connected to the
OPTICAL IN jack :
Press INPUT SELECT on the remote control a third
time. The “AV3 OPT” appears in the display window.
Audio will come from an external source connected
to the OPTICAL IN jack (for rear panel).
To listen and view to an audio source connected
to the AUDIO jack of AV3 IN with video from AV3:
Press INPUT SELECT on the remote control a fourth
time. The “AV3” appears in the display window and
TV screen. Audio and Video will come from an exter-
nal source connected to the AUDIO/VIDEO jacks of
AV3 IN (for front panel).DVD VIDEO
TUNER 
FM/AM
INPUT
SELECT
 
						

							14GB
Mini Glossary
Mini Glossary for Audio Stream
and Surround mode
Allows you to enjoy 5.1(or 6) discrete channels of high quality
digital audio from DTS programme sources such as discs,
DVD and compact discs, etc.bearing the trademark. DTS
Digital Surround delivers up to 6 channels of transparent
audio(which means identical to the original masters) and
results in exceptional clarity throughout a true 360 degree
sound field. The term DTS is a trademark of DTS Technology,
LLC. Manufactured under license from DTS Technology, LLC.
(Dolby Digital)
The Dolby Digital surround format lets you enjoy up to 5.1
channels of digital surround sound from a Dolby Digital pro-
gramme source. If you play DVDs with “ ” mark, you can
enjoy even better sound quality, greater spatial accuracy, and
improved dynamic range. 
(Dolby Pro Logic)
Use this mode when playing movie or Dolby Digital 2 channel
which carries the “ ” mark. This mode provides the effect
of being in a movie theatre or live concert house-an effect with
an intensity which can only be obtained through DOLBY PRO
LOGIC SURROUND. The effect of the front/back/left/right
movement of the sound image, as well as the sense of fixed
position in the sound image, is much clearer and more dynam-
ic than before.
(Dolby Pro Logic II)
Dolby Pro Logic II creates five full-bandwidth output channels
from two-channel sources. This is done using an advanced,
high-purity matrix surround decoder that extracts the spatial
properties of the original recording without adding any new
sounds or tonal colorations.
MOVIE mode:
The Movie mode is for use with stereo television shows and all
programs encoded in Dolby Surround. The result is enhanced
soundfield directionality that approaches the quality of discrete
5.1-channel sound.
MUSIC mode:
The Music mode is for use with any stereo music recordings,
and provides a wide and deep sound space. The Music mode
includes controls that allow the sound to be tailored to individual
listening tastes.
MATRIX mode:
The Matrix mode is the same as the Music mode except that the
directional enhancement logic is turned off. It may be used to
enhance mono signals by making them seem “larger.” The
Matrix mode may also find use in auto systems, where the fluc-
tuations from poor FM stereo reception can otherwise cause dis-
turbing surround signals from a logic decoder. The ultimate
“cure” for poor FM stereo reception may be simply to force the
audio to mono.
3D SURROUND
This unit can produce a 3D Surround effect, using 3D Surround
Sound technology, which simulates multi-channel audio play-
back from two conventional stereo speakers instead of the five
or more speakers normally required to listen to multi-channel
audio from a home theatre. This feature works with DVD discs
encoded with Dolby Pro Logic and Dolby Digital audio tracks.
BYPASS
Software with multichannel surround audio signals is played
according to the way it was recorded. 
Sound Mode
You can enjoy surround sound simply by selecting one
of the pre-programmed sound fields according to the
programme you want to listen to.
Press SOUND FIELDrepeatedly until the sound mode
you want appears in the display window as below.
Each time you press SOUND FIELD button,  the sound
mode is changed in the following order; 
PRO LOGIC →PL2 MOVIE → PL2 MUSIC →PL2 MATRIX →
3D SURROUND →BYPASS
When DVD is inserted.
You can change the sound mode of DVD (Dolby Digital, DTS,
PRO LOGIC, etc) by pressing the AUDIObutton on the remote 
during playback.
Although the DVD contents differ from disc to disc, the follow-
ing explains the basic operation when this feature is used.
Each time you press AUDIO button, the sound mode of DVD is
changed as the following order; 
→→→
For your reference
•The DVD/VCR Receiver memorizes the last mode 
settings for each source individually.
•You can identify the encoding format of pro-
gramme software by looking at its packaging.
-Dolby Digital discs are labeled with the  logo.
-Dolby Surround encoded programs are labeled with
the logo.
-DTS Digital Surround discs are marked with DTS.
Note
When you play sound tracks with 96kHz sampling frequency, the
output signals will be converted to 48kHz (sampling frequency).
Volume Control
You can adjust the volume by rotating VOLUME on the
front panel or by pressing VOL (+/–) on the remote con-
trol repeatedly.
Muting
Press MUTING to mute your unit. 
You can mute your unit in order, for example, to answer
the telephone, “MUTING” indicator in the display win-
dow. To exit mute mode, press MUTING again.
 
						

							PREPARATION
15GB
VIDEO Operation Setup
Video channel set
Video channel (RF output channel) is the channel on
which your TV receives picture and sound signals from
the DVD/VCR Receiver through the RF cable.
If you have used a 
SCARTlead you will not have to tune
your TV, simply select the AVchannel. The AVchannel
is already pre-tuned for optimum video playback on
your TV. 
Perform the following steps only if interference appears
in the TV picture after you have moved to a different
area or a new station has started broadcasting in your
area, or if you change the connection from RF connec-
tion to AV connection, or vise versa.
1 1
Turn on DVD/VCR Receiver and TV.
2
Set the vacant position 52 on your TV.
3
Press @ / 1on the remote control to enter the
standby mode.
4 4
Press and hold CH/PRESET + or – on the
DVD/VCR Receiver for more than 
4 seconds.
RF 52will appear in the DVD/VCR Receiver dis-
play.
The following picture will be displayed on the TV
screen.
If the picture is snowy, move to step 5. 
If the picture is clean, press @ / 1on the DVD/VCR
Receiver to store the RF channel. The video chan-
nel is now set.
5 5
Press CH/PRESET + or – on the DVD/VCR
Receiver to set the video channel to a vacant
position between 22 and 68 which is not occu-
pied by any local station in your area.
You can also set it to “OFF” if there is any inter-
ference when your TV is connected to the
DVD/VCR Receiver.
Note
The RF channel will not change until step 6 has been
executed.
6 6
Press @ / 1to store the new RF channel into the
DVD/VCR Receiver.
7
Press @ / 1to bring the DVD/VCR Receiver from
standby to on and follow your TV manufacturers
tuning instruction manual to tune a new channel
to the DVD/VCR Receiver.
How to use the main menu
This DVD/VCR Receiver can easily be programmed by
using the menus displayed on screen.
The menus are controlled from the Remote Control
Handset.
1 1
Switch on your TV set and DVD/VCR Receiver
by pressing @ / 1.
2
2
Press MENU (i).
The main menu will appear on the TV screen.
Indicates current 
selected icon.
z zREC
Timer recording setting (see pages 27).
z
zPR SET 
Manual tuning setting (see page 16-17).
z zACMS 
ACMS (Automatic Channel Memory System) (see
page 16).
z zTIME DATE
Date and clock setting (see page 18).
OSYSTEM
To set the Colour TV System  (see page 19).
OABC OSD
To change the language setting for OSD. You can
select the language from English, German,
French, Italian, Spanish, Dutch, and Portuguese.
OfOSD ON/OFF
To display the operational mode of your
DVD/VCR Receiver (see page 30).
O16:9/4:3
To select the aspect ratio of your TV 
(see page 28).
OOPR
To improve the playback picture (see page 24).
ONIC
To activate or deactivate the NICAM digital sound
(see page 28).
3 3
Press B or bto select the desired menu.
4
4
Press ENTER/OK and press Vor vto select.
5
5
Press MENU (i) to return to a TV picture. 
Note
The VIDEO main menu will appear incorrectly when NTSC
video source is inputted to the DVD/VCR Receiver.
i RF   CHANNEL           52SETP
R
RECRECOKi
SYS-
TEMP
SET
RPr-12ACMSOSDON
OFFOSDf12TIME
DATE16:9
4:3OPRNICAB
COSD
 
						

							16GB
VIDEO Operation Setup (Continued)
Tuning in TV Stations Automatically
Should you wish to perform the Automatic Channel
Memory System (ACMS) again please follow the guid-
ance given on this page. You may tune up to 88 TV
stations into your DVD/VCR Receiver. 
1 1
Press @ / 1to turn on your DVD/VCR Receiver.     
2
Press MENU (i). 
The main menu will appear on the TV screen.
3
Press Borbto select ACMS and press
ENTER/OK
4 4
Press ENTER/OK again to start the automatic
tuning process.
5 5
While automatic tuning is taking place the time and
date will set automatically. If - - : - - appears in the
DVD/VCR Receiver display it means that the broad-
cast signal is weak and the clock was not set.
Please turn to TIME DATE section of this book on
page 18.
6 6
Press MENU (i) to remove the menus from the
TV screen.
Tuning in TV Stations Manually
In certain areas of the country broadcast signals may
be too weak for your DVD/VCR Receiver’s automatic
tuning process to find or assign TV stations correctly.
You must tune in these weaker broadcast stations man-
ually in order for your DVD/VCR Receiver to store them.
1 1
Press MENU (i).
The main menu will appear on the TV screen. 
2 2
Press Borbto select PR SET and press
ENTER/OK.
3 3
Press MENU (i) and press Vorvto select the
programme number that you want to tune (for
example, PR 06). Press ENTER/OK
4 4
Press Vorvto find out the station that you
want to tune and press b.
If the frequency number is known, enter the
channel number of station that you want to tune
with the numerical buttons.
ACMSD
OKiPr-12ACMS
02 C26 00 BBC2
03 C30 00 ITV
04 C33 00 CH4
05 C35 00 CH5
06  - - - - - - - - -
07  - - - - - - - - -
08  - - - - - - - - -01 C23 00 BBC1
SETP
ROKi , DELETE :MOVE :
   
01 C23 00 BBC1
02 C26 00 BBC2
03 C30 00 ITV
E S
iPr-12ACMS
PR CH MFT STATION
01  00    BBC1    C23
iSETP
R
02 C26 00 BBC2
03 C30 00 ITV
04 C33 00 CH4
05 C35 00 CH5
06  - - - - - - - - -
  - - - - - - - - -   - - - - - - - - - 07
0801 C23 00 BBC1
OKi , DELETE :MOVE :SETP
R
PR CH MFT STATION
06 - - -  -  -  -  -
i
    C- -
SETP
R
PR CH STATION
06    00    C40MFT
CHANNEL/CABLE : AV
iP
RSET
 
						

							PREPARATION
17GB
VIDEO Operation Setup (Continued)
5 5
Searching will stop when it locates a station.
If the station transmits PDC, the station name will
be added automatically.
Control the fine tuning of the station by pressing 
Vorv.
6
6
Press bto select STATION and press 
ENTER/OK 
The TV station name list will appear.
Press Vorvto select a station name from the
list and press ENTER/OK to select it.
If your station name isn’t on the list do not press
ENTER/OK, but go to stage 7.
7
7
You can change a TV station name manually
rather than using the “standard” names.
Press band press Vorvto select letters and
numbers for the new station name.
Press Borbto move back and forth between
characters. Press ENTER/OK
8 8
Press MENU (i), confirm the station placement. 
9
9
Press MENU (i) to remove the menus from the
TV screen.
Your new TV station has now been tuned into your
DVD/VCR Receiver.
If you wish to manually tune other stations repeat
stages 1 - 9.
Changing the order of TV Stations
After tuning TV stations into your DVD/VCR Receiver
you may wish to changethe order in which they are
stored without having to retune them. The instructions
given on this page will show you how you can simply
move them into your desired order. 
1 1
Press MENU (i).
The main menu will appear on the TV screen.
Press Borbto select PR SET and press
ENTER/OK
2 2
Press MENU (i).
Press Vorvto select the programme number
you want to move (for example, PR 03).
Press b.
3
3
Press Vorvto select the programme number
you want to move to (for example, PR 05).
4 4
Press ENTER/OK
The selected programmewill be moved to the new
programme number. 
5
5
Press MENU (i) to remove the menus from the
TV screen.
If you wish to move other TV stations repeat stages
1 - 4.
PR CH MFT STATION
06 00
i
    C40
SETP
R
PR CH MFT
06 00C40   BORDE  ANGLIITV  BBC2  BBC1
 CH TV
WEST
GRANA
iOKSETP
R
PR CH MFT STATION
06 00C40
iOK
CH TV
SETP
R
02 C26 00 BBC2
03 C30 00 ITV
04 C33 00 CH4
05 C35 00 CH5
06
  C4000
CH TV
  - - - - - - - - -   - - - - - - - - - 07
0801 C23 00 BBC1
OKi , DELETE :MOVE :SETP
R
PR CH MFT STATION
01  00  BBC1    C23
iSETP
R
02
C26 00 BBC2
03
04 C33
00CH4
05 C35 00 CH5
06 C40 00 CH TV
07  - -  - - - - - - -
08  - -  - - - - - - -01C23 00 BBC1
OKi
C30 00 ITV
SETP
R
C30 00 ITV 02C23 00 BBC1
C26 00
 BBC2
04C33
00CH4
05C35 00 CH5
06 C40 00 CH TV
07  - -  - -  - - - - -
08  - -   - -  - - - - - 01
OKi , DELETE :MOVE :
03
SETP
R
02C23 00 BBC1
03C26 00 BBC2
04C33
00CH4
05C35 00 CH5
06 C40 00 CH TV
07  - -  - - - - - - -
08  - -   - -  - - - - - 01
C30 00 ITV
OKiSETP
R
 
						

							18GB
VIDEO Operation Setup (Continued)
Deleting TV Stations
After tuning TV stations into your DVD/VCR Receiver
you may wish to deletea station.
The instructions given on this page will show you how
to easily delete any unwanted TV stations.
1 1
Press MENU (i).
The main menu will appear on the TV screen.
Press Borbto select PR SET and press
ENTER/OK 
2 2
Press MENU (i).
Press Vorvto select the programme number
you want to delete (for example, PR 03).
3 3
Press B.
After a short while, the selected station will be
deleted.
4 4
Press MENU (i) to remove the menus from the
TV screen.
If you wish to delete other TV stations repeat
stages 2 - 3.
How to select Stored TV stations:
Stored TV stations can be selected in either of two
ways.
Press CH+ or CH– to select different stations that
are tuned into your DVD/VCR Receiver.
You may also directly select stations using the
numerical buttonson the remote control.
Setting the Clock Manually
The clock in your DVD/VCR Receiver controls time, day
and date settings for your DVD/VCR Receiver. 
For VIDEO Plus+ system to work correctly the cor-
rect time and date must be set. The clock is set auto-
matically during ACMS(Automatic Channel Memory
System) when your DVD/VCR Receiver detects a chan-
nel that broadcasts a Teletext signal.
If the broadcast signal is weak the clock will not be set
and will require setting manually.
1 1
Press MENU (i).
Press Borbto select TIME DATE and press
ENTER/OK
The auto adjust mode can be set to “OFF” by
pressing Vorvif you want to set the time 
manually.
2 2
Press ENTER/OK
Use the numerical buttons or press V/vor B/b
on the remote control to alter the HOURS, 
MINUTES, DAY, MONTH and YEAR.
Please note your DVD/VCR Receiver uses a 
24-hour clock. e.g. 1pm will be displayed as 13:00.
The day of the week will appear automatically when
you enter the year. 
3 3
If you make a mistake, press Borband enter
the correct details.
4 4
Press MENU (i) to remove the menus from the
TV screen.
Your new clock settings are stored and will appear
on your DVD/VCR Receiver’s Display.
- -
i12TIME
DATEOK
AUTO  ADJUST   :   ON
HH MM DD MM YY
:..-  -
- -- - - -- - - - -
i12TIME
DATE
HH MM DD MM YY
:..00  7 1204TUE
i12TIME
DATE
   12
PR CH MFT STATION
01 00 BBC1
i
    C23
SETP
R
OKi
C35  00 CH5 02C23  00 BBC1
C26  00 BBC2
04C30  00ITV
05C33
 00CH4
06 C40  00 CH TV
07  - -
 - -  - - - - -  - - -
- - - -
0801
03
OKi ,DELETE :MOVE :SETP
R
C35  00 CH5 02C23  00 BBC1
C26  00 BBC2
04
05C33
 00CH4
06C40  00 CH TV
07
0801
03
 - -
- -- - - - -
 - -
- -- - - - -
 - -
- -- - - - -
OKi , DELETE :MOVE :SETP
R
 
						

							PREPARATION
19GB
VIDEO Operation Setup (Continued)
To set the colour system
Your DVD/VCR Receiver is equipped with dual colour
standard, you can play back a tape in PAL and MESE-
CAM.
During playback your DVD/VCR receiver detects the
colour system automatically.
If there is any colour problem please select the colour
system manually.
1 1
Press MENU (i).
The main menu will appear on the TV screen.
2 2
Press Borbto select the SYSTEM.
3
3
Press ENTER/OK and press Vorvto select
according to the COLOUR system used.
AUTO:
Allows PAL or MESECAM signals to be distinguished
automatically.
PA L:
Use when receiving PAL signals or use when playing
back a tape recorded in PAL system.
MESECAM:
Use when receiving MESECAM signals or use when
playing back a tape recorded in MESECAM system
4 4
Press MENU (i) to remove the menus from the
TV screen.
RECOKiPRPr-12ACMS12TIME
DATESYS-
TEMSYS-
TEMOSDON
OFFOSDf16:9
4:3OPRNIC
AB
COSD
RECOKiPRPr-12ACMS12TIME
DATESYS-
TEMSYS-
TEMOPROSDON
OFFOSDf16:9
4:3NICAUTO
PAL
MESECAMAB
COSD
 
						

							20GB
DVD Operation Setup
General Explanation
This manual gives basic instructions for operating the
DVD/VCR Receiver. Some DVDs require specific opera-
tion or allow only limited operation during playback.
When this occurs, the symbol  appears on the TV
screen, indicating that the operation is not permitted by
the DVD/VCR Receiver or is not available on the disc.
On-Screen Display
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
1
Press DVD DISPLAY during playback.
2
Press V/vto select an item.
The selected item will be highlighted.
3
Press B/bto change the setting of an item. 
The number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
press ENTER/OK to execute the setting.
Temporary Feedback Field Icons
Repeat Title
Repeat Chapter
Repeat Track (non-PBC Video CDs only)
Repeat All Tracks (non-PBC Video CDs only)
Repeat A-B
Repeat Off
Resume play from this point
Action prohibited or not available
Notes
zSome discs may not provide all of the features on the
on-screen display example shown below.
zIf no button is pressed for 10 seconds, the on-screen
display disappears.
RESUME
OFF
A   BA—B
ALL
TRACK
CHAPT
TITLE
Items
Title Number
Chapter Number
Time search
Audio language 
and Digital Audio 
Output mode
Subtitle language
Angle
Sound
Function (Press V/vto select desired item)
Shows the current title number and total number of titles,
and skips to the desired title number.
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
Shows the elapsed playing time, and 
searches the point directly from the elapsed time.
Shows the current audio soundtrack language,
encoding method, and channel number, and 
changes the setting.
Shows the current subtitles language, and 
changes the setting.
Shows the current angle number and total number of
angles, and changes the angle number.
Shows the current sound mode, and 
changes the setting.
Selection Method
B/ b,or
Numbers, ENTER/OK
B/ b,./ >or
Numbers, ENTER/OK
Numbers, ENTER/OK
B/ b,or
AUDIO
B/ b,or
SUBTITLE
B/ b,or
ANGLE
B/ b,or
SOUND FIELD
1 /3
1 /12
0:20:09
1 ENG
D
5.1 CH
OFF
1 /1
BYPASS
Items
Track Number
Time
Audio Channel
Sound
Function (Press V/vto select desired item)
Shows the current track number, total number of tracks and
PBC On mode, and skips to the desired track number.
Shows the elapsed playing time (Display only)
Shows the audio channel, and 
changes the audio channel.
Shows the current sound mode, and 
changes the setting.
Selection Method
B/ b,or
Numbers, ENTER/OK
–
B/ b,or
AUDIO
B/ b,or
SOUND FIELD
1 /3
BYPASS
0:20:09
ST
VCD2.0VCD1.1
DVD