Sony Car Stereo Xr C440e Xr C450e Xr C440 Xr C450 Manual
Here you can view all the pages of manual Sony Car Stereo Xr C440e Xr C450e Xr C440 Xr C450 Manual. The Sony manuals for Car Stereo System are available online for free. You can easily download all the documents as PDF.
Page 11
– 11 – (E, Saudi Arabia model) (XR-C450)
Page 12
– 12 – (E, Saudi Arabia model)
Page 13
– 13 – (US, Canadian model) (E, Saudi Arabia model)
Page 14
– 14 – Note: Follow the disassembly procedure in the numerical order given. FRONT PANEL ASS’Y SECTION 2 DISASSEMBLY 1Push the button (release). A 2 Remove the front panel ass’y to the direction of the arrow A. COVER ASS’Y 2 1 3cover ass’y 1 2
Page 15
– 15 – SUB PANEL, MECHANISM DECK5screw (PTT2.6 × 6) 6mechanism deck 4flexible flat cable (CN301) 1three screws (PTT2.6 × 8) 1three screws (PTT2.6 × 8) MAIN BOARD, HEAT SINK 2sub panel 3connector (CN302) 2two ground point screws 4nine screws (PTT2.6 × 10) 1two screws (PTT2.6 × 8) 3main board 5 heat sink 1screw (PTT2.6 × 8)
Page 16
– 16 – Note: Follow the assembly procedure in the numerical order given. SECTION 3 ASSEMBLY OF MECHANISM DECK 2Install the hanger onto two claws of the housing.1Install the catch to the hanger. 7Holder the hanger by bending the claw. Apar t Bpart Cpar t Dpar t 8Hold the hanger by bending the claw. 3Put the housing under A part. 4Fit claw on B part. 6Fit projection on D part. 5Fit projection on C part. hanger HOUSING 2Move the arm (suction) in the arrow direction and fit on projection. 1Fit the arm...
Page 17
– 17 – 1Fit the lever (LDG-A) on shafts A – C and install it. shaft A shaft C 4type-E stop ring 2.0shaft A shaft B LEVER (LDG-A) / (LDG-B) GEAR (LDG-FT) 3Align hole in the gear (LDG-D) with hole the lever (LDG-A).gear (LDG-FB) hole gear (LDG-D) lever (LDG-A) 2Move the lever (LDG-B) in the arrow direction. 1tension spring (lever LDG) 5gear (LDG-FT) 5polyethyene washer hole shaft B 3Fit the lever (LDG-B) on shafts A and B and install it. 2Pull the lever in the arrow direction.
Page 18
– 18 – GUIDE (C) 2guide (C) 1three claws
Page 19
– 19 – SECTION 4 MECHANICAL ADJUSTMENTSSECTION 5 ELECTRICAL ADJUSTMENTS TEST MODE This set have the test mode function. In the test mode, FM Auto Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments can be performed easier than it in ordinary procedure. 1. Set the “OFF” mode. 2. Push the preset 4 button. 3. Push the preset 5 button. 4. Press the preset 1 button for more than two seconds. 5. Then the display indicates all lights, the test mode is set. 1. Push the “OFF” button. 1. Clean the...
Page 20
– 20 – TUNER SECTION (XR-C450: E, Saudi Arabia model only) Cautions during repair When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair. FM Auto Scan/Stop Level Adjustment Setting: SOURCE button : FM FREQUENCY SELECT switch : 10 k 0dB=1µV FM RF signal generator Carrier frequency : 97.9 MHz Output level : 22 dB (12.6 µV) Mode : mono Modulation : 1 kHz, 75 kHz deviation 0.01 µF set antenna jack (J1) Procedure: 1. Set to the test mode. (See page 19)....