Sony Bdv It1000 Operating Instructions

							51GB
Getting Started
7Reattach the rear cap using the wrench (supplied).
8Secure the speaker to the bracket with the screw in Step 3 using hole 4.
4
 
						

							52GB
Getting Started
Step 3: Connecting the System
See the connection diagram below, and read the additional information from 1 to 8 on the following 
pages.
Note Be sure to make connections securely to avoid hum and noise.
 When you connect another component with a volume control, turn up the volume of the other components to a level 
where sound is not distorted.
BDV-IT1000
HDMI S-AIR
4 AM loop antenna (aerial)
1 Subwoofer8 AC power cord (mains lead) 4 FM wire antenna (aerial) 2 TV
1 Front left speaker (L)1 Center speaker
1 Front right speaker (R)
1 Surround left speaker (L)1 Surround right speaker (R)
:Signal flow 3 DIGITAL MEDIA 
PORT adapter
5 Wireless 
transceiver
8 AC power cord 
(mains lead) Surround amplifier5 Wireless 
transceiver 7 Network6 External 
memory3 Set-top box/digital satellite 
receiver, VCR, or PlayStation, 
etc.
 
						

							53GB
Getting Started
BDV-IS1000
HDMI S-AIR
4 AM loop antenna (aerial)
1 Subwoofer8 AC power cord (mains lead) 4 FM wire antenna (aerial) 2 TV
1 Front left speaker (L)
1 Center speaker
1 Front right speaker (R)
1 Surround left speaker (L)1 Surround right speaker (R)
:Signal flow 3 DIGITAL MEDIA 
PORT adapter3 Set-top box/digital satellite 
receiver, VCR, or PlayStation, 
etc.
5 Wireless 
transceiver
8 AC power cord 
(mains lead) Surround amplifier5 Wireless 
transceiver 7 Network6 External 
memory
 
						

							54GB
Getting Started
Front/center speakers and subwoofer for BDV-IT1000
When connecting speaker cords to the unit, insert the connector until it clicks.
When connecting the speaker cords to the subwoofer, use the speaker cords (purple). Be sure to match 
the speaker cords to the appropriate terminals on the speakers: the speaker cord with the color tube to 
3, and the speaker cord without the color tube to #. Do not catch the speaker cord insulation in the 
speaker terminals.
1 Connecting the Speakers
COAXIAL OPTICAL
COAXIAL 75FM
AMANTENNA DIGITALHDMI
DMPORTEZW-RT10
TV
SAT/CABLE IN VIDEO OUT IR REMOTE
LAN(100)
EXTERNAL
SPEAKER SAT/CABLE
COMPONENT VIDEO OUT
COMPONENT VIDEO IN
A.CAL
MIC
SAT/CABLE TV
IN 1 IN 2 OUTIN
700mA
MAX ECM-AC2 AUDIO INOUT IN
AUDIO
VIDEO Y
YP
B/
P
B / CBPR / CR
CBPR/
CR
L R
L RDC5V DC5V 500mA  MAX
S-VIDEO VIDEO
FRONT
RFRONT
LCENTER WOOFER
S
P
E
A
K
E
R
FR
O
N
T
RFR
O
N
T
LC
E
N
TERW
O
O
FER
Rear panel of the unit
To the center speaker (green)To the subwoofer (purple)
To the front right speaker (R) (red)
To the front left speaker (L) (white)
#
3
Color tube (purple)Rear of the subwoofer
Connector (purple)
 
						

							55GB
Getting Started
Front/center speakers and subwoofer for BDV-IS1000
When connecting to the unit, insert the connector until it clicks.
The speaker cords (yellow and purple) are connected to the subwoofer beforehand as follows. When 
re-connecting, be sure to match the speaker cords to the appropriate terminals on the speakers: the 
speaker cord with the color tube to 3, and the speaker cord without the color tube to #. Do not catch 
the speaker cord insulation in the speaker terminals.
COAXIAL OPTICAL
COAXIAL 75FM
AMANTENNA DIGITALHDMI
TV
SAT/CABLE IN EXTERNAL
SPEAKER SAT/CABLE
COMPONENT VIDEO OUT
COMPONENT VIDEO IN
A.CAL
MIC
SAT/CABLE TV
IN 1 IN 2 OUTIN
ECM-AC2 AUDIO IN
AUDIO
VIDEO Y
YP
B/
P
B / CBPR / CR
CBPR/
CR
L R
L R DC5V 500mA  MAX
S-VIDEO VIDEO
FRONT
RWOOFER
1WOOFER
    2 FRONT
LCENTER
LAN(100)
VIDEO OUT
DMPORT700mA
MAX DC5V
EZW-RT10
S
P
E
A
K
E
R
FR
O
N
T
RFR
O
N
T
LC
EN
TE
R
WOOFER
1WOOFER
     2
Rear panel of the unit
To the center speaker (green) To the subwoofer (purple)
To the front right speaker (R) (red)
To the front left speaker (L) (white)To the subwoofer (yellow)
#
3
Color tube 
(yellow)
Rear of the subwoofer Connector (yellow)
Connector (purple)#
3
Color tube 
(purple)
 
						

							56GB
Getting Started
Surround speakers
About the speaker cords of the front/center speakers and subwoofer
You can remove the speaker cords from the connector. With the catch facing down, press and hold the 
connector down against a flat surface (1) and remove the speaker cords from the connector (2).
When attaching the speaker cords to the connector, be sure to match the polarity of the speaker cords 
and the connector.
Note Short-circuiting of the speakers may damage the system. To prevent this, make sure the bare wire of each speaker 
cord does not touch another speaker terminal or the bare wire of another speaker cord.
 Be sure to match the speaker cords to the appropriate speaker terminals: 3 to +, and # to –. If the cords are 
reversed, the sound will lack bass and may be distorted.
Rear panel of the surround amplifier
RSURROUND SELECTOR
S-AIR ID
EZW-RT10
SPEAKER
SURROUNDPA I R I N GCB ASURROUND
BACK
LL
R
S
P
E
A
K
E
R
To the surround left speaker (L) 
(blue)
To the surround right speaker (R) (gray)
Catch(1)
(2)
Connector3
#
 
						

							57GB
Getting Started
Use the parts as follows:

To listen to TV sound from the six speakers of the system, connect the TV and the system with the 
audio cord (not supplied) (A).
For video output to your TV, check the video input jacks of the TV, and select connection method A, 
B, C, or D. Picture quality improves in order from A (standard) to D (HDMI).
When the TV has the digital optical output jack, you can improve sound quality by connecting with the 
digital optical cord (not supplied) (B).
* If your TV accepts progressive format signals, make this connection.
** HDMI (High-Definition Multimedia Interface)
If your TV has the HDMI jack, make this connection.
2 Connecting the TV
COAXIAL OPTICAL
COAXIAL 75FM
AMANTENNA DIGITALHDMI
DMPORTEZW-RT10
TV
SAT/CABLE IN VIDEO OUT IR REMOTE
LAN(100)
EXTERNAL
SPEAKER SAT/CABLE
COMPONENT VIDEO OUT
COMPONENT VIDEO IN
A.CAL
MIC
SAT/CABLE TV
IN 1 IN 2 OUTIN
700mA
MAX ECM-AC2 AUDIO INOUT IN
AUDIO
VIDEO Y
YP
B/
P
B / CBPR / CR
CBPR/
CR
L R
L RDC5V DC5V 500mA  MAX
S-VIDEO VIDEO
FRONT
RFRONT
LCENTER WOOFER
VIDEO OUTS
-V
ID
E
O V
ID
E
O
VIDEO OUTS
-V
ID
E
O V
ID
E
OCOMPONENT VIDEO OUTYPB/
CBPR/
CRCOAXIAL OPTICAL
DIGITALSAT/CABLE TVIN
TVA
U
D
IO
 INL R
O
U
T
Rear panel of the unit
(Ex. BDV-IT1000) To the component video input jacks of 
the TV
To the HDMI IN jack of the TV To the video input jack of 
the TV
To the audio output jacks of the TV Component video cord
(not supplied)*
Video cord
(supplied)HDMI** cable
(not supplied) Audio cord 
(not supplied) Green
Blue
Red
White
RedTo the digital optical output 
jack of the TVDigital optical cord
(not supplied) S video cord
(not supplied)
To the S video input jack 
of the TV
 
						

							58GB
Getting Started
About the HDMI connection
If you connect a 1080/24p- or 1080p-compatible TV, use a High Speed HDMI cable.
If you connect a Sony TV that is compatible with the Control for HDMI function (page 105), operation 
is simplified (ex. ONE-TOUCH PLAY: With one touch of the button, the connected TV turns on and 
the input selector on the TV is switched to the system automatically). For details, see “Using the 
Control for HDMI Function for “BRAVIA” Sync” (page 105).
Note Be sure to use only an HDMI cable that bears the HDMI logo.
 When connecting the HDMI cable, make sure that the direction of jacks are the same.
.
To connect to a TV with DVI input
Use an HDMI-DVI converter cable (not supplied). The DVI jack does not accept audio signals; 
therefore, the sound is not output from a TV.
Furthermore, you cannot connect the HDMI OUT jack to DVI jacks that are not HDCP compliant (e.g., 
DVI jacks on PC displays).
 
						

							59GB
Getting Started
You can enjoy the connected component(s) using the six speakers of the system.
 Set-top box/digital satellite receiver, VCR, or PlayStation, etc. (without HDMI OUT jack): 1
 Set-top box/digital satellite receiver or PLAYSTATION
®3, etc. (with HDMI OUT jack): 2 
 DIGITAL MEDIA PORT adapter: 3
3 Connecting the other components
COAXIAL OPTICAL
COAXIAL 75FM
AMANTENNA DIGITALHDMI
DMPORTEZW-RT10
TV
SAT/CABLE IN VIDEO OUT IR REMOTE
LAN(100)
EXTERNAL
SPEAKER SAT/CABLE
COMPONENT VIDEO OUT
COMPONENT VIDEO IN
A.CAL
MIC
SAT/CABLE TV
IN 1 IN 2 OUTIN
700mA
MAX ECM-AC2 AUDIO INOUT IN
AUDIO
VIDEO Y
YP
B/
P
B / CBPR / CR
CBPR/
CR
L R
L RDC5V DC5V 500mA  MAX
S-VIDEO VIDEO
FRONT
RFRONT
LCENTER WOOFER
COAXIAL OPTICAL
DIGITALSAT/CABLE TVIN
11
2
3
S
AT/C
AB
LECOMPONENT VIDEO 
INY
PB
 / CBPR
 / CR
S
A
T/C
AB
LE
 INAUDIO
VIDEOL R
S
A
T/C
AB
LE
 INAUDIO
VIDEOL R
DMPORT700mA
MAX DC5V
HDMIIN 1 IN 2
Rear panel of the unit
(Ex. BDV-IT1000)
To the component video output jacks of 
the componentTo the HDMI OUT jack 
of the component
To the video output 
jack of the component B Component video cord
(not supplied)HDMI cable
(not supplied)A Audio cord 
(not supplied)
Green
Blue
RedWhite
Red
To the digital optical output jack of the component
To the digital coaxial output jack of the componentB Digital optical cord
(not supplied)
B Digital coaxial cord
(not supplied)
or Audio connection
To the audio output jacks of the 
component
Video connection
A Video cord
(not supplied)
DIGITAL MEDIA PORT 
adapter
 
						

							60GB
Getting Started
Connection 1 (SAT/CABLE jacks)
You need to make both video and audio connections.
For video connection, check the video output jacks of the component, and select a connection method. 
B (component) offers the better picture quality than A (standard).
For audio connection, connect the audio cords (A). If the component has a digital optical or coaxial 
output jack, you can improve sound quality by connecting with the digital cord (B).
Note The system can accept both digital and analog signals. Digital signals have priority over analog signals. (COAXIAL 
has priority over OPTICAL.) If the digital signal ceases, the analog signal will be processed after 2 seconds.
Connection 2 (HDMI IN1/2 jacks)
When connecting the system and the component using an HDMI cable, you can enjoy high quality 
digital pictures and sound through the HDMI IN1 or 2 jack. You can connect up to two components.
Note When connecting the HDMI cable, make sure that the direction of jacks are the same..
Connection 3 (DMPORT jack)
Connect a DIGITAL MEDIA PORT adapter (not supplied) to the DMPORT jack. For details, see 
“Using the DIGITAL MEDIA PORT Adapter” (page 98).
Note Connect the DIGITAL MEDIA PORT adapter so that the V marks are aligned. When disconnecting, pull out while 
pressing A.
A