Sony Bdv It1000 Operating Instructions

							Other Operations
111GB
Note When you perform [Auto Calibration] in the Easy 
Setup (page 69), the default settings are changed.
 Depending on the input stream, [Distance] may not 
be effective.
x[Level]
You can adjust the sound level of the speakers, 
center speaker, and subwoofer. You can set the 
parameters from –6.0 dB to +6.0 dB. Be sure to 
set [Test Tone] to [On] for easy adjustment.
[Front L/R] 0.0 dB
: Set the front speaker level.
[Center] 0.0 dB
*: Set the center speaker level.
[Surround L/R] 0.0 dB
*: Set the surround 
speaker level.
[Surround Back L/R] 0.0 dB
*: Set the surround 
Back speaker level.
[Subwoofer] 0.0 dB
: Set the subwoofer level.* This item appears when you set to [Yes] in the 
[Connection] setting.
x[Test Tone]
The speakers will emit a test tone to adjust 
[Level].
[Off]
: The test tone is not emitted from the 
speakers.
[On]: The test tone is emitted from each speaker 
in sequence while adjusting level. When you 
select one of the [Speaker Settings] items, the 
test tone is emitted from each speaker in 
sequence.
Adjust the sound level as follows.
1Set the [Test Tone] to [On].
2Press C/X/x/c repeatedly to select the 
desired speaker and the level.
3Press .
4Repeat Steps 1 to 3.
5Press C/X/x/c repeatedly to set [Test 
Tone] to [Off] after adjusting the 
speaker level.
Note The test tone signals are not output from the HDMI 
OUT jack.
Tip To adjust the volume of all the speakers at one time, 
press 2 +/–.
Controlling the TV or 
Other Components with 
the Supplied Remote
By adjusting the remote signal, you can control 
your TV, a Sony component (such as a VCR, 
DVD player/recorder, etc.), CATV, or set-top 
box/digital satellite receiver with the supplied 
remote.
Note When you replace the batteries of the remote, the 
code number may reset itself to the default (SONY) 
setting. Reset the appropriate code number.
1Press POP UP/MENU while pressing 
TV (for TV) or STB (for a Sony 
component, CATV, set-top box/digital 
satellite receiver, etc.).
TV or STB (pressed button) flashes.
2While TV or STB is flashing, enter the 
manufacturer’s code (see the table) 
using the number buttons, then press 
TIME.
If you successfully set the manufacturer’s 
code, TV or STB will flash twice slowly. If 
the setting is unsuccessful, TV or STB will 
flash five times quickly.
Code numbers of controllable 
components
If more than one code number is listed, try 
entering them one at a time until you find the 
code that works with your TV.
TV
Preparing the remote for 
controlling the components
Manufacturer Code number
SONY 5001 (default), 5002
AIWA 5001
AKAI 5003
DAEWOO 5003, 5015, 5044
GE 5003, 5009, 5010, 5044
GOLDSTAR/LG 5003, 5015, 5017, 5044, 5068
 
						

							112GB
Sony component
CATV
HITACHI 5003, 5014, 5015, 5017, 5044, 
5057, 5071
JVC 5016
KMC 5017
MAGNAVOX 5003, 5015, 5017, 5018, 5044, 
5066
MARANTZ 5027
MITSUBISHI/MGA 5003, 5027, 5044, 5066, 5068
NEC 5003, 5017, 5044, 5066
PANASONIC 5009, 5053, 5072
PHILIPS 5015, 5018, 5057, 5070, 5071
PIONEER 5009, 5025, 5051
RCA/PROSCAN 5003, 5010, 5044
SAMPO 5066
SAMSUNG 5003, 5015, 5017, 5044, 5057, 
5066, 5069, 5074
SHARP 5017, 5035, 5065
TOSHIBA 5035, 5041, 5051
VCR 7001, 7002, 7003
DVD player/recorder 4001, 4002, 4003, 4004
Manufacturer Code number
SONY 8501
ABC 8513, 8555
ADELPHIA 8507, 8510
ADVANCED 
NEWHOUSE8507
ALTRIO 8507
AMERICAST 8505
ATLANTIC 
BROADBAND8507
BELL & HOWELL 8513
BELL SOUTH 8505
BLUE RIDGE 8507
BRIGTH HOUSE 8507
CABLEVISION 8507
CHARTER 8507
COMCAST 8507
COX 8507
DIRECTOR 8503
GEMINI 8036, 8543
Manufacturer Code number
GENERAL 
INSTRUMENT8018, 8032, 8503, 8512, 8513, 
8514, 8515, 8516, 8517, 8518, 
8519, 8532, 8553, 8554, 8557
GNC 8505
GOLDSTAR 5825
HAMLIN 8023, 8024, 8025, 8026, 8532, 
8533, 8534, 8535, 8536
ILLICO 8507
JERROLD 8001, 8002, 8003, 8004, 8005, 
8006, 8007, 8008, 8018, 8022, 
8032, 8503, 8512, 8513, 8514, 
8515, 8516, 8517, 8518, 8519, 
8532, 8553, 8554, 8557
MACOM 8033, 8034, 8035, 8540, 8541, 
8542
MAGNAVOX 8037
MEMOREX 8506, 8523, 8544
MOTOROLA 8503, 8510, 8511
NET 8030, 8552
OAK 8027, 8028, 8029, 8537, 8538, 
8539
PACE 8507
PANASONIC 8019, 8020, 8021, 8523, 8529, 
8530, 8531
PARAGON 8506, 8523
PHILIPS 8039, 8040, 8041, 8043, 8044, 
8504, 8546, 8547, 8548, 8549, 
8550, 8551
PIONEER 8014, 8015, 8507, 8525, 8526
PULSAR 8506, 8523
QUASAR 8523
REGAL 8532, 8533, 8534, 8535, 8536
RODGERS 8507
RUNCO 8506, 8523
SAMSUNG 8038, 8525, 8545
SCIENTIFIC 
ATLANTA8009, 8010, 8011, 8502, 8507, 
8508, 8509, 8520, 8521, 8522, 
8555, 8556
SEREN 8507
SIGECOM 8507
SUSQUEHANNA 8507
TIME WARNER 8507
TOCOM 8016, 8017, 8031, 8527, 8528, 
8553
TOSHIBA 8506, 8523
VIDEOTRON 8507
Manufacturer Code number
 
						

							Other Operations
113GB
Set-top box/digital satellite 
receiver
WIDEOPENWEST 8505, 8507
ZENITH 8012, 8013, 8505, 8506, 8523, 
8524
Manufacturer Code number
SONY 8201, 8202 (default), 8203, 
8701, 8702, 8703
ADB 8262
ALPHASTAR 8710
AMSTRAD 8204, 8225, 8226, 8247, 8259
B sky B 8243
CANAL + 8208
CROSSDIGITAL 8717
DGTEC 8292, 8293, 8294
DIRECTV 8713, 8717, 8718, 8719, 8723, 
8714
DISH NETWORK 8712, 8714, 8725
ECHOSTAR 8712, 8720
GALAXIS 8212, 8214, 8216, 8232, 8233, 
8254, 8272
GE 8719
GENERAL 
INSTRUMENT8711
Gold Box 8238
Grundig 8228, 8229, 8237, 8265
HIRSCHMANN 8263
HITACHI 8707
HUGHES 8706
Hyundai 8245
Jerrold 8240
JVC 8712, 8714, 8720
KATHREIN 8224, 8244, 8250
MAGNAVOX 8715, 8716, 8718
MATSUI 8227
MEMOREX 8716
NIKKO 8223
NOKIA 8219, 8239, 8257, 8276, 7277
NTV PLUS 2000 8242
On digital 8273
PACE 8217, 8218, 8222, 8243, 8260, 
8261
PANASONIC 8267, 8705
Manufacturer Code number
PAYSAT 8716
PHILIPS 8255, 8278, 8715, 8716, 8718
PROSCAN 8704, 8709, 8719
RADIX 8213, 8226, 8231, 8253
RCA 8704, 8709, 8719, 8721
SABA 8210, 8211, 8230, 8234, 8235, 
8248, 8270, 8286
SAMSUNG 8287, 8288, 8717, 8722
Sky 8243
SKY MASTER 8205, 8207, 8285
Sky+ 8295
STAR SIGHT 8716
STRONG 8289, 8290, 8291
TECHNISAT 8220, 8221, 8236, 8241, 8246, 
8252, 8266, 8268, 8279, 7280
Thomson 8234, 8271, 8274, 8275
TOMSON 8283, 8284
TOSHIBA 8708
TPS 8256
UNIDEN 8715, 8716
WATSON 8206
Zehnder 8209, 8215, 8249, 8251, 8264, 
8268, 8269, 8281, 8282
Manufacturer Code number
 
						

							114GB
You can control the TV using the following 
buttons. To use these buttons, set the remote to 
the TV mode by pressing TV (TV lights up for 1 
second).
Note During the TV mode, if you press any of the 
following buttons, TV lights up. (Depending on the 
manufacturer setting, some buttons may not work, 
and TV does not light up.)
 When you press other than the following buttons 
during the remote is in the TV mode, TV does not 
light up.
 Depending on the TV, you may not be able to control 
your TV or to use some of the buttons.* Only available for the component that is connected 
to the TV with the HDMI or iLINK connection. For 
details, see the operating instructions of the TV.
Tip The function of these buttons are same as the remote 
buttons of the Sony TV. For details, refer to the 
operating instructions of the TV.
Controlling the TV with the 
remote
By pressing You can
AV "/1Turn the TV on or off.
THEATRE Enjoy optimal image suited for 
movies.
t/ Switch the TV’s input source 
between the TV and other input 
sources.
After pressing /, you can hold 
the current text page.
2 +/– Adjust the TV volume.
PROG +/–,
c/CSelect the TV channel.
After pressing /, you can select 
the next (c) or previous (C) text 
page.
Turn off the TV sound 
temporarily.
Number buttons, 
-Select the TV channel.
After pressing /, you can select 
the text page by entering the three 
digit page number.
HOME Display the menu of the TV.
ANALOG Switch to analogue mode.
DIGITAL Switch to digital mode.
/ Display the information.
/Access text.
Display the Digital Electronic 
Programme Guide (EPG).
TOOLS Display the operation menu for the 
current display.
RETURN Return to the previous channel or 
layer on the menu of the TV.
Change the aspect ratio of the 
connected TV.
C/X/x/c, Select the item on the menu.
H* Start playback.
X* Pause playback.
x* Stop playback.
./>* Skips to the previous/next chapter, 
track, or file.
* Replay the scene/briefly fast 
forward the scene.
m/M* Fast reverse/fast forward during 
playback.
By pressing You can
 
						

							Other Operations
115GB
You can control the Sony component such as a 
VCR or DVD player/recorder, CATV, or set-top 
box/digital satellite receiver using the following 
buttons. To use these buttons, set the remote to 
the STB mode by pressing STB (STB lights up 
for 1 second).
Note During the STB mode, if you press any of the 
following buttons, STB lights up. (Depending on the 
manufacturer setting, some buttons may not work, 
and STB does not light up.)
 When you press other than the following buttons 
during the remote is in the STB mode, STB does not 
light up.
 Depending on the component, you may not be able to 
control the component or to use some of the buttons.
* Only available for Sony component such as a VCR, 
DVD player/recorder, etc.
Using the Sound Effect
You can enjoy sound effects or dialog, as you 
would in a movie theater, even at low volume. It 
is useful for watching movies at night.
Press NIGHT.
“NIGHT ON” appears in the front panel display 
and the sound effect is activated.
During the night mode is on, “NIGHT” lights up 
in the front panel display.
Note When sound is output from the center speaker, this 
effect is more pronounced, as speech (movie dialog, 
etc.) is easy to hear. When sound is not output from 
the center speaker, or you are using the headphones, 
the system optimally adjusts the volume.
To turn off the sound effect
Press NIGHT so that “NIGHT” disappears from 
the front panel display.
You can adjust the sound by changing the tonal 
balance of the sound.
1Press TONE repeatedly until the 
desired setting appears in the front 
panel display.
 “BASS”: You can adjust the bass 
frequencies.
 “MIDDLE” (BDV-IS1000 only): You 
can adjust the middle frequencies.
 “TREBLE”: You can adjust the treble 
frequencies.
2Press X/x to adjust the sound.
The adjusted value appears in the front 
panel display. You can set the value from 
–6.0 to +6.0. 
Controlling the Sony 
component, CATV, or set-top 
box/digital satellite receiver
By pressing You can
AV "/1Turn the set-top box/digital 
satellite receiver on or off.
PROG +/– Select the set-top box/digital 
satellite receiver channel.
Number buttons, 
ENTERSelect the set-top box/digital 
satellite receiver channel.
HOME Display the menu of the set-top 
box/digital satellite receiver.
OPTIONS
Display the options menu that can be 
selected appears on the TV screen.
RETURN Return to the previous channel or 
layer on the menu of the set-top 
box/digital satellite receiver.
CLEAR Clear the entry field.
C/X/x/c, Select the item on the menu.
DVD 
RECORDER 
(HDD, DVD)*Change the operation mode for 
Sony DVD recorders.
H* Start playback.
X* Pause playback.
x* Stop playback.
* Briefly fast forward the scene.
m/M* Fast reverse/fast forward during 
playback.
Enjoying the sound at low 
volume
Adjusting the sound
 
						

							116GB
Using the Sleep Timer
You can set the system to turn off at a preset 
time, so you can fall asleep listening to music. 
You can preset the time in 10-minutes 
increments.
Press SLEEP.
Each time you press SLEEP, the minutes display 
(the remaining time) changes by 10-minutes.
When you set the sleep timer, “SLEEP” flashes 
in the front panel display.
To check the remaining time
Press SLEEP once.
To change the remaining time
Press SLEEP repeatedly to select the desired 
time.
Deactivating the Buttons 
on the Unit
(Child Lock)
You can deactivate the buttons on the unit 
(except for "/1) for preventing misoperation, 
such as child mischief (child lock function).
Press x on the unit for more than 5 
seconds.
“CHILD LOCK” and “ON” appear in the front 
panel display.
The child lock function is activated and the 
buttons on the unit are locked. (You can operate 
the system by using the remote.)
To cancel, press x for more than 5 seconds so 
that “
CHILD LOCK” and “OFF” appear in the 
front panel display.
Note When you operate the buttons on the unit while the 
child lock function is on, “CHILD LOCK” appears in 
the front panel display.
 
						

							Settings and Adjustments
117GB
Using the Setup Display
You can make various adjustments of items such 
as picture and sound.
Select   (Setup) on the home menu when you 
need to change the settings of the system.
Note Playback settings stored in the disc take priority over 
the Setup Display settings and not all the functions 
described may work.
1Press HOME.
The home menu appears on the TV screen.
2Press C/c to select   [Setup].
3Press X/x to select the setup category 
icon to change, then press  .
Example: [Video Settings]You can setup the following options.
4Press X/x to select an item, then press 
.
The options for the selected item appear.
Example: [TV Type]
Settings and Adjustments
Setup
Video Settings
Audio Settings
BD/DVD Viewing Settings
Photo Settings Network Update
Setup
TV Type
Set the screen aspect ratio of your TV.
Screen FormatOriginal
DVD Aspect RatioLetter Box
Auto
Cinema Conversion Mode
Icon Explanation
[Network Update] (page 118)
Updates the software of the 
system.
[Video Settings] (page 119)Makes the video settings 
according to the type of 
connecting jacks.
[Audio Settings] (page 121)Makes the audio settings 
according to the type of 
connecting jacks.
[BD/DVD Viewing Settings] 
(page 122)
Makes detailed settings for BD/
DVD playback.
[Photo Settings] (page 124)Makes the photo-related 
settings.
[HDMI Settings] (page 124)Makes the HDMI settings.
[System Settings] (page 126)Makes the system-related 
settings.
[Network Settings] (page 127)Makes detailed settings for 
Internet and network.
[Easy Setup] (page 128)Re-runs the Easy Setup to make 
the basic settings.
[Resetting] (page 129)Resets the system to the factory 
settings.
Setup
TV Type 16:9
4:3
Screen Format
DVD Aspect Ratio
Cinema Conversion Mode
Options
 
						

							118GB
5Press X/x to select a setting, then 
press .
The setting is selected and setup is 
complete.
The options for the selected item appear.
Example: [4:3][Network Update]
You can update and improve the functions of the 
system.
For information about update functions, refer to 
the following website;
http://www.sony.net/
1Press X/x to select [Network Update], 
then press  .
The unit connects to the network, and the 
display asks for confirmation.
2Press C/c to select [OK], then press 
.
The unit starts downloading, then updating 
the software automatically.
When updating finishes, “COMPLETE!” 
appears for 5 seconds in the front panel 
display, then the system automatically turns 
off.
3Press "/1 to turn the system on.
The system starts up with the updated 
software.
Note Do not disconnect the AC power cord (mains lead) or 
network cable while downloading or updating 
software.
 Any operations, including opening the disc tray, are 
not available while updating.
 Downloading times may differ depending on the 
server provider or line status.
 When error messages on network connections 
appear, check the network connections using 
[Network Diagnostic] of [Internet Settings] in 
[Network Settings] (page 127).
Tip The “UPDATE */9” counter (“*” indicates update 
step) in the front panel display also shows progress of 
the update.
 You can check the current software version by 
selecting [System Information] in [System Settings] 
(page 126).
 The [Setup] settings remain after updating.
 The system informs you of newer software version 
information when [Software Update Notification] is 
set to [On] (default) (page 126).
Setup
TV Type
Set the screen aspect ratio of your TV.
Screen FormatOriginal
DVD Aspect RatioLetter Box
Auto
Cinema Conversion Mode4 : 3
Selected setting
 
						

							Settings and Adjustments
119GB
To update the software using an 
update disc
You can update and improve the functions of the 
system using an update disc provided by Sony 
dealer or local authorized Sony service facility. 
1Insert the update disc.
The display asks for confirmation.
2Select [OK], and press  .
Software update starts.
When updating finishes, “COMPLETE!” 
appears for 5 seconds in the front panel 
display, then the disc tray automatically 
opens.
3Remove the disc.
The system automatically turns off.
4Press "/1 to turn the system on.
The system starts up with the updated 
software.
Note Do not disconnect the AC power cord (mains lead) 
while updating.
 Any operations, including opening the disc tray, are 
not available while updating.
Tip The “UPDATE */9” counter (“*” indicates update 
step) in the front panel display also shows progress of 
the update.
 You can check the current software version by 
selecting [System Information] in [System Settings] 
(page 126).
 The [Setup] settings remain after updating.
 For information about other software update 
methods, refer to the following website or consult 
your nearest Sony dealer or local authorized Sony 
Service facility;
http://www.sony.net/
[Video Settings]
You can make the video settings according to 
the type of connecting jacks.
x[TV Type]
You can select the aspect ratio of the connected 
TV.
[16:9]
: Select this when connecting to a wide-
screen TV or a TV with a wide mode function.
[4:3]: Select this when connecting to a 4:3 
screen TV without a wide mode function.
x[Screen Format]
You can select the display configuration for a 
4:3 screen picture on a 16:9 wide screen TV.
[Original]
: Select this when connecting to a TV 
with a wide mode function. Displays a 4:3 
screen picture in 16:9 aspect ratio even on a 
wide-screen TV.
[Fixed Aspect Ratio]: Changes the picture size 
to fit the screen size with the original picture 
aspect ratio.
x[DVD Aspect Ratio]
You can select the display configuration for 
playback of 16:9 screen pictures on a 4:3 screen 
TV (selectable when [TV Type] is set to [4:3] 
and [Screen Format] is set to [Fixed Aspect 
Ratio]).
[Letter Box]
: Displays a wide picture with black 
bands on the top and bottom.
[Pan & Scan]: Displays a full-height picture on 
the entire screen, with trimmed sides.
 
						

							120GB
x[Cinema Conversion Mode]
You can set the video conversion method for 
480p/576p, 720p, 1080i, or 1080p* signals from 
the HDMI OUT jack or the COMPONENT 
VIDEO OUT jacks.
* HDMI only
[Auto]: Normally select this. The unit 
automatically detects whether the material is 
video-based or film-based, and switches to the 
appropriate conversion method.
[Video]: The conversion method suited for 
video-based material will always be selected 
regardless of the material.
x[Output Video Format]
Select the jack type to output video signals ([TV 
Connection Method]), then select output 
resolution for the HDMI/component connection 
([HDMI Resolution]/[Component Resolution]).
1Press X/x to select the jack type to 
output video signals, then press  .
Note When connecting the HDMI OUT jack and 
other video output jacks at the same time, select 
[Component Video].
[TV Connection Method]
[HDMI]: Outputs signals from the HDMI 
OUT jack according to the [HDMI 
Resolution] setting below.
[Component Video]: Outputs signals from 
the COMPONENT VIDEO OUT jacks 
according to the [Component Resolution] 
setting below.
[Video or S Video]
: Outputs signals from 
the VIDEO OUT (VIDEO) or VIDEO OUT 
(S VIDEO) jack.
2(When you select [HDMI] or 
[Component Video])
Press X/x to select the signal type for 
the HDMI OUT jack or COMPONENT 
VIDEO OUT jacks, then press  .
When you change the video output 
resolution, a picture is displayed in the 
selected resolution for about 30 seconds, 
then the display asks for confirmation.
Follow the on-screen instructions.“HD” lights up in the front panel display 
when outputting 720p/1080i/1080p video 
signals.
Note If the picture is distorted or no picture appears, 
wait for about 30 seconds without pressing any 
buttons. The display returns to the resolution 
setting screen.
 If the selected video output resolution is 
incorrect, no picture appears on the screen when 
you press any button in 30 seconds. In this case, 
press and hold H and A on the unit for more 
than 5 seconds to reset the video output 
resolution to the lowest resolution.
 When connecting the HDMI OUT jack and 
other video output jacks at the same time, video 
signals may not output from the jacks, other than 
from the HDMI OUT jack, when [Auto] or 
[1080p] is selected.
[HDMI Resolution]/[Component 
Resolution]
[Auto] (HDMI only): Normally select this.
The unit outputs signals starting from the 
highest resolution acceptable to the TV:
1080p > 1080i > 720p > 480p/576p > 480i/
576i
If the resulting image format is undesirable, 
try another setting that suits your TV.
[480i/576i]: Outputs 480i/576i video 
signals.
[480p/576p]: Outputs 480p/576p video 
signals.
[720p]: Outputs 720p video signals.
[1080i]: Outputs 1080i video signals.
[1080p] (HDMI only): Outputs 1080p 
video signals.
x[Pause Mode] (BD/DVD VIDEO/DVD-R/
DVD-RW only)
You can select the picture in pause mode.
[Auto]
: The picture, including subjects that 
move dynamically, is output with no jitter. 
Normally select this position.
[Frame]: The picture, including subjects that do 
not move dynamically, is output in high 
resolution.