Sony Bdv E970w Operating Instructions

11GB
A"/1 (Power)
Turns the surround amplifier on/off.
BS-AIR/STANDBY indicator
You can check the status of wireless 
transmission between the main unit and 
surround amplifier.
CS-AIR ID switch
Selects the S-AIR ID.
DPAIRING button
Starts pairing.
EPAIRING indicator
Indicates the pairing status.
FSURROUND SELECTOR switch
Selects the mode for the surround amplifier.
GSPEAKERS jacks
HWireless transceiver (EZW-RT10) slot
Surround amplifier
LRSURROUND SELECTORSURROUNDPAIRING
ABCSURROUND...

12GB
Number 5,  , 2 +, and N buttons have a 
tactile dot. Use the tactile dot as a reference 
when operating the remote.
 : For TV operations
(For details, see “Controlling Your TV with 
the Supplied Remote” (page 53).)
ATHEATRE (page 49) 
Switches to the optimum video mode for 
watching movies automatically.
ONE-TOUCH PLAY (page 49)
Activates One-Touch Play.
TV "/1 (on/standby) (page 53) 
Turns on the TV or sets it to standby mode.
"/1 (on/standby) (pages 28, 42)
Turns on the system or sets it...

13GB
FPlayback operation buttons 
See “Playback” (page 32). 
./> (previous/next)
Skip to the previous/next chapter, track, or 
file.
 (replay/advance)
Briefly replay the current scenes for 10 
seconds./Briefly fast forwards the current 
scenes for 15 seconds.
m/M (fast reverse/fast forward)
Fast reverse/fast forward the disc during 
playback. Each time you press the button, 
search speed changes.
Activates slow-motion play when pressed 
for more than one second in pause mode. 
Plays one frame at a time...

14GB
Getting Started
Step 1: Installing the System
For the best possible surround sound, place all speakers at the same distance from the listening position 
(A). The distance can be between 0.0 to 7.0 meters.
If you cannot place the center speaker and surround speakers at the same distance as (A), place them 
within 7.0 meters of the listening position.
Place the surround speakers to the rear of the listening position (B).
The subwoofer can be placed anywhere in the room.
Note Use caution when placing...

15GB
Getting Started
To add the optional surround back speakers
You can enjoy 7.1 surround sound by purchasing the Wireless Surround Speaker Kit (WAHT-SBP2, 
optional). The optional product lineup differs depending on the area.
For the position of the surround back speakers, refer the illustration below (C).
Note To use the surround back speakers, set [Surround Back] (page 51) in [Speaker Settings] to [Yes] while performing 
the Easy Setup (page 28).
Caution
 Contact a screw shop or installer regarding...

16GB
Getting Started
To disassemble the speaker
(Front and surround speakers of BDV-E970W only)
1Disconnect the speaker cords from the speaker.
2Remove the screw (pre-installed) at the rear of the speaker.
This screw is used when reassembling the speaker. Be sure not to lose the screw.
3Disassemble the speaker by lifting the upper part of the speaker.
Rear of the speaker
Rear of the speaker Screw
Upper part
Lower part
Rear of the speaker
 

17GB
Getting Started
4Pull out the speaker cord from the bottom of the lower part of the speaker.
The removed speaker cord is used when installing the speaker on a wall.
5Remove the protection paper from the speaker-bottom cover, then attach the speaker-
bottom cover to the bottom of the upper part of the speaker.
Note When removing the protection paper, pull it off via the section exposed by the notch in the speaker-bottom cover.
Fully-disassembled illustration
Lower part of the speaker
,
Speaker cord...

18GB
Getting Started
To install the speakers on a wall
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with 
the color tube to 3, and the speaker cord without the color tube to #.
1Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. 
See the illustrations below.
2Fasten the screws to the wall.
Color tube
Front left speaker (L): White...

19GB
Getting Started
3Hang the speakers on the screws.
5 mm 
10 mmHole on the back of 
the speaker
Rear of the speaker
 

20GB
Getting Started
Step 2: Connecting the System
For connecting the system, read the information on the following pages.
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other 
connections are made.
Note When you connect another component with a volume control, turn down the volume of the other components to a 
level where sound is not distorted.
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker....