Sony Bdv E800w Operating Instructions

21GB
Getting Started
To connect speaker cords to the unit
When connecting to the unit, insert the connector until it clicks.
To connect speaker cords to the speaker
RS
U
R
RO
U
N
D
 
S
E
L
E
C
T
O
R
S
-A
IR
 ID
EZW-R
T10
SPEAKER
S
U
R
RO
U
N
DPA I
RINGCB AS
U
R
RO
U
N
D
B
A
C
K
L
AUD
IO
D
IG
IT
A
L
 IN
DMPORTH
D
M
I O
U
T
C
O
M
P
O
N
E
N
T
 V
ID
E
O
 O
U
TV
ID
E
O
 O
U
TS-AIR IDA
U
DI
O
 
INA
U
DIO
 IN
A. CAL MICE
C
M
-A
C
2
SPEAKER
YPB
 /
 
CBPR
 / CR
COAXIALOPTICAL
R L
R L
FRONT RFRONT L
CENTER...

22GB
Getting Started
This connection sends a video signal to the TV.
Depending on the jacks on your TV, select the connection method.
* The HDMI cable is supplied with Singapore, Indonesian, Malaysian, Hong Kong, and Filipino models only.
Method 1: Video cord (A) connection
This is the basic connection.
Method 2: HDMI* cable (B) and video cord (A) connection
If your TV has an HDMI jack, connect to the TV both with an HDMI cable and video cord. Picture 
quality will be improved compared to using only the...

23GB
Getting Started
To change the color system (PAL or NTSC)
Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color 
system.
The initial setting of the system for Middle Eastern models is PAL.
The initial setting of the system for Asian models is NTSC.
1Turn on the system by pressing "/1.
2Press x and VOLUME + on the unit simultaneously for more than 5 seconds.
Each time you perform this operation, the color system toggles between PAL and NTSC.
“NTSC”...

24GB
Getting Started
This connection sends an audio signal to the unit from the TV. To listen to TV sound via the system, 
perform this connection.
Method 1: Audio cord (D) connection
This is the basic connection and sends an analog audio signal.
Method 2: Digital optical cord (E) connection
When the TV has a digital optical output jack, you can improve sound quality by connecting with a 
digital optical cord in addition to an audio cord connection.
With a digital audio connection, the system receives a...

25GB
Getting Started
You can enjoy connected components via the system’s speakers.
 DIGITAL MEDIA PORT adapter (not supplied): F
 VCR, digital satellite receiver, PlayStation, or portable audio source, etc. (not supplied): G
 VCR or digital satellite receiver, etc. (not supplied) which has a digital coaxial output jack: H
Note Connect the DIGITAL MEDIA PORT adapter so that the V marks are aligned. When disconnecting, pull out while 
pressing .
If your TV has multiple audio/video inputs
You can enjoy...

26GB
Getting Started
To connect the antenna (aerial)\
Note Be sure to fully extend the FM wire antenna (aerial).
 After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM 
antenna (aerial) as shown below.
Connecting the antenna (aerial)
AUD
IO
S-AIR IDA
U
DI
O
 I
NA
U
DIO
 
IN
A. CAL MICE
C
M
-A
C
2
R L
R LE
X
T
EZW-R
T10
TV
A
BCDC5V500mA  MAX
A
N
T
E
N
N
A
F
MC
O
A...

27GB
Getting Started
You can transmit sound from the unit to an S-AIR product, such as the surround amplifier or S-AIR 
receiver.
To transmit sound from the unit, you need to insert the wireless transceivers into the unit and S-AIR 
product.
For details of S-AIR products, see “Using an S-AIR Product” (page 61).
Inserting the wireless transceiver
RS
U
R
RO
U
N
D
 
S
E
L
E
C
T
O
R
S
-A
IR
 ID
EZW-R
T10
SPEAKER
S
U
R
RO
U
N
DPA I R I N GCB AS
U
R
RO
U
N
D
B
A
C
K
L
AUD
IO
D
IG
IT
A
L
 IN
DMPORT
S-AIR IDA
U...

28GB
Getting Started
Insert the external memory device (1 GB or larger USB flash memory, such as Sony USM2GL, 
USM4GL, or USM1GH, not supplied) into the EXT slot. Check that “EXT” lights up in the front panel 
display when turning the system on. By connecting an external memory, you can enjoy additional 
contents (BonusView/BD-Live) depending on the disc (page 47).
\
Note Insert the external memory into the EXT slot as far as it will go.
 Insert the external memory straight. If you force the external...

29GB
Getting Started
Connect the LAN (100) terminal of the unit to your Internet source using a network cable to update the 
system’s software using the network. You can also enjoy BD-Live (page 47).
Make the appropriate settings in [Internet Settings] under [Network Settings] (page 87).
\
To update the system’s software using the network
See [Network Update] (page 78) and [Software Update Notification] (page 86).
Note Do not connect a phone line to the LAN (100) terminal, as it may cause a malfunction....

30GB
Getting Started
Before connecting the AC power cords (mains leads) of the unit and the surround amplifier to a wall 
outlet (mains), connect the front, center speakers and subwoofer to the unit and surround speakers to 
the surround amplifier.
\
To turn off the demonstration mode
After connecting the AC power cord (mains lead), the demonstration appears in the front panel display. 
You can turn off the demonstration simply by pressing "/1 on the remote. For details, see “About the...