Sony Ae 5 Service Manual

21
• When complete readjustment is necessary or a new 
picture tube is installed, carry out the following 
adjustments.
• Unless there are specific instructions to the contrary,
carry out these adjustments with the rated power supply.
• Unless there are specific instructions to the contrary, set the 
controls and switches to the following settings:
Contrast ............... normal
Brightness ............... normalCarry out the following adjustments in this order:
3-1. Beam Landing
3-2. Convergence
3-3....

22
(Open)
(Close)
B
G
RB
G
R
B
GR
Fig.3-4
 
Fig. 3-5
3-2. CONVERGENCE
(1) Screen centre convergence 
[Static convergence]
1. Input a dot signal from the pattern generator. 
Normalize the picture setting.
2. [Moving horizontally], adjust the H.STAT control so that the 
horizontal red, green and blue dots coincide at the centre of the 
screen.
3. [Moving vertically], adjust the V.STAT magnet so that the
vertical red, green and blue dots coincide at the centre of the 
screen.• If the horizontal dots are...

23
B
GR
B G R
B
G
R
HMC correction(A) HMC correction(B)
A <  B
A =  BRG B
RG B
A >  B
A =  BRGB
RG B
C < D
C = D C > D C = D
R
G
B C
DC
DR
G
BR
G
BR
G
B VMC correction(A) VMC correction(B)
c). By rotating the V.STAT magnet clockwise, the red, green and 
blue dots move in the direction indicated below.
d). By opening or closing the V.STAT magnet, the red, green and 
blue dots move in the direction indicated below.
Note :If the blue dot does not coincide with the red and
green points correct the points by...

24
FOCUS
Layout of each control
Fig 3-5
Note :If you are unable to adjust the corner convergence
properly, this can be corrected with the use of 
permalloys.
3-3. FOCUS
1. Receive a television broadcast signal.
2. Normalize the picture setting.
3. Adjust the focus control located on the flyback transformer to 
obtain the best focus at the centre of the screen.
Bring only the centre area of the screen into focus, the 
magenta-ring appears on the screen. In this case, adjust the 
focus to optimize the...

25
    White balance adjustment for TV mode
1. Input an all-white signal.
2. Enter into the Service Mode by pressing ‘TEST’, ‘TEST’ and 
‘MENU’ ‘MENU’on the Service Commander.
3. Select ‘Backend’ from the on screen menu 
display and press ‘OK’.
4. The ‘Backend’ menu will appear on the screen.
5. Set the contrast to MAX.
6. Set the ‘R DRIVE’ to 41.
7. Adjust the ‘G DRIVE’ and ‘B DRIVE’ so that the white
balance becomes optimum.
8. Press the ‘OK’ button to write the data for each item.
9. Set the contrast...

26
SECTION 4
CIRCUIT ADJUSTMENTS
4-1. ELECTRICAL ADJUSTMENTS
Service adjustments to this model can be performed using the supplied Remote Commander RM-891.
HOW TO ENTER INTO SERVICE MODE
1. Turn on the main power switch of the set while pressing PROG + (plus) and PROG - (minus) buttons on the top panel.
2. TT will appear in the upper right corner of the screen.
3. Press the ‘MENU’ button twice on the remote commander to obtain the service menu on the screen.
4. Push the joystick up or down on the remote...

27
Fig.4-1Model Setting
1 KV-29FX60A/D/E
2KV-29FX60B
3KV-29FX60U
4 KV-29FC60A/D/E
5 KV-29FC60B
6 KV-29FC60K
7 KV-29FC60R
8 KV-29FS60A/D/E
9KV-29FS60B
10 KV-29FS60K
11 KV-29FS60R
12 KV-28/32FX60A/D/E
13 KV-28/32FX60B
14 KV-28/32FX60K
15 KV-28/32FX60R
16 KV-28/32FX60U
17 KV-29FS60A/D/E
18 KV-29FS60B
Fig.4-2Basic setting
No Descr. Min Max Data
1 Sys.B/G OFF ON ON
2 Sys.D/K OFF ON ON
3Sys.L OFFON ON
4 Sys I (UK) OFF ON OFF
5 Sys I (IRL) OFF ON OFF
6 Russian sound OFF ON OFF
7 TXT Nod.option 1 4 3
8 s i m p l...

28
Fig.4-4Feature setting
No Descr. Min Max Data
1PIP OFFON ON
Fig.4-5Colour Decoder 1
No Descr. Def Min Max Data
1 DelayLinMd OFF OFF ON OFF
2Gain set 1031
3 Y-Delay 7 0 15 7
4Phase Time 0030
5 Vid Ident Md OFF OFF ON OFF
6 Sync Mode OFF OFF ON OFF
7 Vid Ident Sw ON OFF ON ON
8 H-Output OFF OFF ON OFF
9 Enagating OFF OFF ON OFF
10 IF Circuit ON OFF ON ON
11 GP Delay OFF OFF ON OFF
Fig.4-6Colour Decoder 2
No Descr. Def Min Max Data
1 DelayLinMd OFF OFF ON OFF
2Gain set 1031
3 Y-Delay 7 0 15 7
4Phase Time...

29
Fig.4-9Feature Low-End
No Descr. Def Min Max Data
1 F.S.F.M OFF OFF ON OFF
2 G-Mode OFF OFF ON OFF
3 Picture Pos 0 0 3 0
4 Comp Mode OFF OFF ON OFF
5 CompSW OFF OFF ON OFF
6 Acqu.freq OFF OFF ON OFF
7 Still Pic OFF OFF ON OFF
8 Init OFF OFF ON OFF
9 Dis Feature ON OFF ON ON
10 Dis Vlimit ON OFF ON ON
11 Scr Fade 0 0 3 0
12 Hwe Delay 20 0 255 20
13 Auto Vshift OFF OFF ON OFF
14 Vwe Delay 0 0 127 0
15 SFR sw OFF OFF ON OFF
16IPQ 0030
17 D.Col Dec OFF OFF ON OFF
18 Blankfield 0 0 15 0
19 P1.5 OFF OFF ON...

30
Feature Low-End (Cont.)
No Descr. Def Min Max Data
81 Dcti Thres 0 0 15 0
82Dcti Gain 0070
83 Dcti Super ON OFF ON ON
84 Dcti Fil ON OFF ON ON
85 Dcti Prot ON OFF ON ON
86 Dcti Sep ON OFF ON ON
87Dcti Limit 2032
88Peak Beta 0070
89Peak Alpha 2072
90Peak Neg g 0030
91Peak Delta 0030
92Peak Tau 0070
93 Peak Corth 0 0 15 0
94Overlay V 0 0150
95Overlay U 0 0150
96 Overlay Y 10 0 255 10
97 Sidep sta 240 0 255 240
98 Sidep sto 36 0 255 36
99Y delay B 7077
100 Invert UV ON OFF ON ON
101 Output Range ON  OFF...