Snow Blower Stiga DUO LINE+ SNOW FLAKE SNOW POWER SNOW TRACK 8218-2232-80 Norwegian Version Manual

51
 ENGLISHEN
3.6 CONTROL KNOBS, FIG. 5
1.  Screw the nut (J) onto the gear lever.
2.  Mount the control knob (K) onto the gear lever.
3.  Tighten the nut on the underside of the control knob.
3.7 GEAR LEVER, SE FIG. 6
Set the gear lever in a suitable position to simple assemble 
the ball-and-socket joint (L) into the hole in the lever (M).
Assemble the washer and tighten with the nut supplied.
3.8 CHECKING THE CONTROL WIRES
The control wires might need adjusting before using the 
snow thrower for the...

52
 ENGLISHEN
4.18 BAND TILT (19)
See fig. 13. Only valid for SNOW TRACK
To press down the auger further at hard and packed snow, the 
bands can be tilted backwards.
Aktivating the band tilt
Lift the handlebar until the bands are locked in tilted 
position.
Resetting the band tilt
Lift the handlebar and press down the pedal pedalen (19) 
until the bands are locked in their normal position.
4.19 CHUTE CLEARING TOOL (15, FIG. 7/8)
The chute clearing tool is located in a holder on top of the au-
ger...

53
 ENGLISHEN
Note: The electrical starting motor has overload 
protection. The motor stops automatically when 
overheated. It will not restart until it has cooled, which 
takes about 5 - 10 minutes.
8.  When the engine starts, turn the choke anti-clockwise 
until it is fully open. 
Never run the machine indoors. The exhaust 
fumes contain carbon monoxide, a very toxic gas.
5.6 STOPPING
1.  Release both clutch levers. Note. If the snow thrower 
continues rotating - see ADJUSTING THE CONTROL 
WIRES...

54
 ENGLISHEN
7 LUBRICATION
No service must be carried out before: 
The engine has stopped. 
The ignition key has been removed. 
- The starting cable has been disconnected from 
the spark plug.
If the instructions say that the machine is to be lifted at the 
front and rested on the auger housing then the petrol tank 
must be emptied.
Empty the petrol tank outdoors when the engine is 
cold. Do not smoke. Empty into a container 
designed for petrol.
7.1 DISCHARGER
Lubricate the discharger flange and the...

55
 ENGLISHEN
6.  Replace the belt (E in fig. 16). NOTE! Only genuine 
STIGA belts are to be used.
7.  Adjust the belt tension according to the above 
instructions.
8.  Assemble the belt guide (D) in fig 16.
9.  Adjust the belt tension according to the above 
instructions.
10. Reassemble the belt protection.
11. Adjust the control wire according to the below 
instructions.
8.3.2 THE DRIVING BELT
1.  Carry out items 1-5 above.
2.  Remove the locking ring (17) from the swing plate shaft 
(18). See fig 23....

56
 ENGLISHEN
- Check that the washers (17 in fig. 28) are correctly 
placed.
- Check that the washers (13 in fig. 28) are correctly 
placed.
- Check that the shaft (8 in fig. 29) rotates freely.
- Check that the friction wheel and disc drive plate are 
totally free from oil and grease.
8.6.4 Byte av friktionshjulet (FLAKE, POWER)
1.  Disassemble the differential, see 8.7.2.
2.  Dismantle the two bearing mountings (16 in fig 18).
3.  Dismantle the shaft and bearing mountings. Note the 
location of the...

57
 ENGLISHEN
9 STORAGE
Never store the snow thrower with petrol in the 
tank in a confined area with bad ventilation. Petrol 
fumes could reach open flames, sparks, cigarettes 
etc.
If the snow thrower is to be stored for a longer period than 30 
days, the following measures are recommended:
1.  Empty the petrol tank.
2.  Start the engine and let it run until it stops due to lack of 
fuel.
Empty the petrol tank outdoors when the engine is 
cold. Do not smoke. Empty into a container 
designed for...

58
FRANÇAISFR
1 SYMBOLES
Les symboles suivants figurent sur la machine. Ils attirent 
votre attention sur les dangers d’utilisation et les mesures à 
respecter. 
Explication des symboles :
Attention.
 Lire le mode d’emploi avant d’utiliser la machine.
 Danger – fraise en rotation.
 Danger – ventilateur en rotation.
 Écarter les mains de l’éjecteur.
Éloigner les mains et les pieds des éléments en 
rotation. 
 Respecter une distance de sécurité suffisante.
 Ne jamais orienter l’éjecteur vers des personnes...

59
FRANÇAISFR
• Il est interdit de déconnecter les dispositifs de sécurité ou 
d’en empêcher le fonctionnement.
• Ne pas modifier le réglage du moteur. Ne pas pousser le 
moteur à plein régime. Le risque de blessure augmente 
lorsque le moteur tourne à plein régime.
• Ne pas déneiger à proximité de clôtures, véhicules, 
fenêtres ou sur des pentes escarpées sans adapter le 
déflecteur déjection. 
• Éloigner les enfants des zones à déneiger et confier leur 
surveillance à un adulte.
• Ne pas surcharger la...

60
FRANÇAISFR
3.6 POMMEAU – LEVIER, FIG. 5
1.  Visser l’écrou (J) sur le levier de vitesses.
2.  Monter le pommeau (K) sur le levier de vitesse.
3. Serrer l’écrou situé en dessous du pommeau.
3.7 ACCÉLÉRATEUR, VOIR FIG. 6
Mettre le levier d’accélérateur situé sur le guidon dans une 
position permettant d’installer aisément le joint à rotule (L) 
dans l’orifice du levier (M).
Installer la rondelle et serrer à l’aide de l’écrou fourni.
3.8 VÉRIFICATION DES CÂBLES
Il peut être nécessaire de procéder au...