Home > Smeg > Dishwasher > Smeg Stc75 Instruction Manual

Smeg Stc75 Instruction Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Smeg Stc75 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							User instructions 
    66
    GENERAL WARNINGS AND RECOMMENDATIONS FOR CORRECT 
    MAINTENANCE: 
    xThe filters should be cleaned under running water using a stiff 
    brush. 
    xWhen removing the filter, take care that there are no food residues 
    on it. If any residues fall into the washing pit they might block 
    hydraulic components, or foul the spray arm nozzles. 
    xIt is essential to thoroughly clean the filters according to the above 
    instructions: the dishwasher cannot function if the filters are clogged. 
    xCarefully replace the filters in their seats, to avoid damaging the 
    wash pump. 
    PROLONGED DISUSE: 
    xRun the soak program twice in succession. 
    xUnplugthe power cord from the socket. 
    xLeave the door slightly open,  in order to prevent the formation of 
    unpleasant odours inside the washing tank. 
    xFill the rinse aid dispenser.
    xShut off the water supply tap. 
    BEFORE STARTING THE DISHWASHER AFTER PROLONGED 
    DISUSE: 
    xCheck that there are no deposits of sludge or rust inside the water 
    pipe: if there are, allow the water to run from the water supply tap for a 
    few minutes. 
    xPlug the power cord back into the socket. 
    xReconnect the water intake hose and open the tap again. 
    TROUBLESHOOTING MINOR PROBLEMS 
    In some cases it is possible to remedy minor problems by referring to the 
    following instructions: 
    If the program fails to start, check that: 
    xthe dishwasher is connected to the electrical power supply; 
    xthere is no power failure; 
    xthe water tap is open; 
    xthe dishwasher door is properly closed.
    If water remains inside the dishwasher, check that: 
    xthe drain hose is not kinked; 
    xthe drain siphon is not obstructed; 
    xthe dishwasher filters are not clogged. 
         GI     
    						
    							User instructions 
    67
    If the dishes do not come out clean, check that: 
    xthe correct amount of detergent has been added; 
    xthere is regenerating salt inside the special container; 
    xthe dishes are being loaded correctly; 
    xthe selected program is suitable for the dish types and their degree 
    of soiling; 
    xall the filters are clean and positioned correctly; 
    xthe spray arm nozzles are not obstructed; 
    xthere is no object obstructing the rotation of the spray arms;
    xthe detergent dispenser hatch has not been prevented from opening 
    properly by an incorrectly positioned item.
    If the dishes fail to dry or remain dull, check that: 
    xthere is rinse aid inside the special container; 
    xthe rinse aid dispenser setting is correct; 
    xthe detergent used is of good quality and has not lost its 
    effectiveness (for example, through incorrect storage, with the box 
    left open). 
    If the dishes show signs of streaking, staining, etc., check that: 
    xthe rinse aid dispenser setting is not too high. 
    If there are visible traces of rust inside the tank: 
    xthe tank is made of steel, and therefore any rust marks are due to 
    external elements (fragments of rust from the water pipes, pots, 
    cutlery, etc.). Special products are commercially available to remove 
    such marks; 
    xcheck that the amount of detergent being used is correct. Certain 
    detergents can be more corrosive than others. 
    xcheck that the cap of the salt container is securely closed, and that 
    the water softening setting is correct. 
    If after following the above troubleshooting instructions the problem 
    persists, call the nearest After-Sales Centre. 
    WARNING: any operations performed on the appliance by 
    unauthorised persons are not covered by the warranty and shall be 
    paid for by the user.
         GI     
    						
    							User instructions 
    68
    6. Troubleshooting 
    The dishwasher is capable of signalling a number of faults through the 
    simultaneous illumination of several indicator lights, with the following 
    meanings: 
    FAULT DESCRIPTION 
    E3
    Water heating malfunction The water is not heated or the heating parameters are not correct. Repeat the washing program; if the problem persists, contact the after-sales service. 
    E4
    Water temperature monitoring malfunction Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service. 
    E5
    Water intake malfunction The appliance does not take in water or does not do so correctly. Check that the water connections are correct, the water intake tap is turned on and the filter is not fouled. If the problem persists, contact the after-sales service. 
    E6
    Water pump-out malfunction The appliance does not pump out the water or does not do so correctly. Check that the drain hose is not kinked or crushed and that the siphon and filter are not fouled. If the problem persists, contact the after-sales service. 
    E7
    Turbine flow-regulator malfunction  (for the relevant models only)The appliance is not able to measure the amount of water loaded accurately. Interrupt the program and switch off the dishwasher. Switch the dishwasher back on, program it again and start the washing cycle. If the problem persists, contact the after-sales service.
    E9
    Water intake system malfunction Contact the after-sales service. 
    Light off  Light on  Light flashing 
         GI     
    						
    							User instructions 
    69
    If an alarm occurs the appliance interrupts the program in progress and 
    signals a fault. 
    xAlarmsE3, E4 and E9 interrupt the current program immediately. 
    xTheE5,E6 alarms interrupts the running program once the cause is 
    resolved, it will bring bach the execution of the program.
    xThe alarm E7 is visualized at the end of the cycle that comes, however, 
    brought to the end since the operation of the dishwasher is not harmed.
    To “reset” an alarm is necessary: 
    xOpen and close the door, or turn off and on the machine. At this point is 
    possible to program the dishwasher again.
    If the malfunction persists, contact your authorised Service Centre. 
    TECHNICAL DATA
    Width559 mm 
    Depth measured flush with the  outer edge of the control panel 550 mm 
    Height578 mm 
    Capacity 7 Standard place settings 
    Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) 
    Electrical characteristics See rating plate 
         GI     
    						
    							898898
    896896
    894894
    0 5 10
    10
    1515
    2020
    2525
    3030
    3535
    4040
    4545
    5050
    5555
    MAXMAX
    MINMIN
    SXSXDXDX
    SXSXDXDX
    5555
    5050
    898898
    896896
    894894
    0 5 10
    10
    1515
    2020
    2525
    3030
    3535
    4040
    4545
     
    						
    All Smeg manuals Comments (0)

    Related Manuals for Smeg Stc75 Instruction Manual