Smeg Sta 4845 Instruction Manual
Have a look at the manual Smeg Sta 4845 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 81 Smeg manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
User instructions 9 3. Description of the controls 3.1 Upper panel All the dishwasher controls are grouped on the upper panel. Switch-on, programming, switch-off, etc. procedures are only possible when the door is open. The panel shown is only a guideline example: the form of the lights and buttons may vary depending on the model. 1 ON/OFF BUTTON Press this button to switch the dishwasher on/off. 2 SELECTED PROGRAM INDICATOR LIGHTS Illumination of this light denotes the program selected and the occurrence of a fault (troubleshooting). 3 PROGRAM SELECTION BUTTON By pressing this button in sequence it is possible to select the desired program. 4 SALT WARNING LIGHT (only some models) Illumination of this light signals that salt container is empty. 5 RINSE AID WARNING LIGHT (only some models) Illumination of this light signals that rinse aid dispenser is empty. 6 OPTIONS (on some models only)
User instructions 10 Depending on the model, this zone may contain one or more of the following options, identified by the relative symbols and described in more detail in the relevant sections of the manual. It is not possible to select any options when the soak program is being used. All options except Flexi Tabs are disabled at the end of the wash cycle. To disable the “Flexi Tabs” option, press the relative button (the light goes out). Flexi Tabs Specifically for the use of products which contain salt and rinse aid as well as detergent. HYCLEAN Adds a final antibacterial rinse to the selected program. PROGRAM DELAY Allows the program to be set to start with a delay of 3, 6 or 9 hours.
User instructions 11 PROGRAMS TABLE The manual contains the programs table for several models. To find the table for your dishwasher, compare the program symbols at the top of the table with those on your control panel. SETTING THE WASHING PROGRAM AND SWITCHING ON After identifying the most suitable program with the aid of the programs table: • Press the ON/OFF button (1) and wait for the PROGRAM INDICATOR LIGHT (2) to illuminate; • Keep pressing the PROGRAM SELECTION button (3) until the indicator light corresponding to the desired program illuminates; • select the option required (if any and if the model provides options); • close the door; after about 2 the program will start LIGHT will flashing (indicating that the program is being executed).
User instructions
12
PROGRAMS TABLE
PROGRAMME NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION CONSUMPTION
MINUTES (1)
WATER LITRESPOWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load Cold prewash 9 5,0 0,02
2 LIGHT
Delicate dishes with light dirt
Wash at 45°C Cold rinse Rinse at 70°C Dry
59
12 0,90
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 55°C Cold rinse Rinse at 66°C Dry
**
** **
4 NORMAL
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 65°C Cold rinse Rinse at 70°C Dry
80
17 1,20
5 SUPER
Very dirty pans and dishes, even with dried-on residues.
Prewash at 45°C Wash at 70°C Cold rinse (2) Rinse at 70°C Dry
105
20 1,50
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
User instructions 13 PROGRAMS TABLE PROGRAMME NUMBER & SYMBOL LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS DURATION CONSUMPTION MINUTES (1) WATER LITRESPOWER KWh (1) 1 SOAK Pans and dishes awaiting completion of the load Cold prewash 9 5,0 0,02 2 RAPID 27’ Dishes with light dirt, washed immediately after use Wash at 38°C Rinse at 50°C 27 6,5 0,70 3 ECO (*) EN 50242 Dishes with normal dirt, even with dried-on residues Cold prewash Wash at 55°C Cold rinse Rinse at 66°C Dry ** ** ** 4 NORMAL Dishes with normal dirt, even with dried-on residues Cold prewash Wash at 65°C Cold rinse Rinse at 70°C Dry 80 17 1,20 5 SUPER Very dirty pans and dishes, even with dried-on residues. Prewash at 45°C Wash at 70°C Cold rinse (2) Rinse at 70°C Dry 105 20 1,50 IMPORTANT: see “NOTES AND REFERENCES” table on the following pages. If the dishwasher door is open or not properly closed, the washing cycle will not start.
User instructions
14
PROGRAMS TABLE
PROGRAMME NUMBER & SYMBOL
LOAD CROCKERY AND CUTLERY PROGRAM PROGRESS
DURATION CONSUMPTION MINUTES (1)
WATER LITRESPOWER KWh (1)
1 SOAK
Pans and dishes awaiting completion of the load Cold prewash 9 5,0 0,02
2 RAPID 27’
Dishes with light dirt, washed immediately after use
Wash at 38°C Rinse at 50°C
27
6,5 0,70
3 ECO (*)
EN 50242
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 55°C Cold rinse Rinse at 66°C Dry
**
** **
4 NORMAL
Dishes with normal dirt, even with dried-on residues
Cold prewash Wash at 65°C Cold rinse Rinse at 70°C Dry
80
17 1,20
5 ULTRA CLEAN
Very dirty pans and dishes, even with dried-on residues.
Prewash at 45°C Wash at 70°C Cold rinse (2) Rinse at 70°C Dry
115
20 1,55
IMPORTANT: see “NOTES AND REFERENCES” table on the following pages.
If the dishwasher door is open or not properly closed, the washing cycle
will not start.
User instructions 15 NOTES AND REFERENCES Only run the soak program with half loads. Options cannot be used with the soak program. * Standard programme under EN 50242. ** See information sheet provided (1) The cycle duration and power consumption may vary according to the water and room temperatures, and the type and amount of dishes. (2) 1 or 2 cold rinses depending on the model. REFERENCES for the ENERGY LABEL supplied with the dishwasher: - Annual energy consumption is based on 280 standard wash cycles with cold water and consumption of low-energy operating modes. Actual consumption depends on the way in which the appliance is used. - Water consumption is based on 280 standard wash cycles. Actual consumption depends on the way in which the appliance is used. - Information refers to the EN 50242 STANDARD programme (identified in the programmes table), which is the most effective in terms of combined energy and water consumption. The programme is recommended for dishes with a normal level of dirt. - Energy consumption in “sleep” mode = 0.02 W. - Energy consumption in “on” mode = 1.5 W. - Drying efficiency class on a scale from “G” (minimum efficiency) to “A” (maximum efficiency).
User instructions
16
3.2 Washing programs
Before starting a washing program make sure that:
• The water supply tap is open.
• The softener container contains regenerating salt.
• The correct amount of detergent has been added to the
dispenser.
• The baskets have been correctly loaded.
• The spray arms are able to rotate freely and without
obstruction.
• The dishwasher door is securely closed.
OPTION SELECTION
Options are selected by pressing the relative button by the symbol of the
option required; the light comes on to confirm that the option has been
activated.
• It is not possible to select any options when the soak
program is being used.
• All options except Flexi Tabs are disabled at the end of the
wash cycle. To disable the “Flexi Tabs” option, press the
relative button (the light goes out).
• All options, including 3/1 are disabled when a program is
CANCELLED after it has begun.
User instructions 17 Flexi Tabs The option is optimised for use of detergents which are complete with salt and rinse aid, known on the market as 3 in 1, triple action, etc. With this option activated, any salt and rinse aid If you wish to use detergents which already contain salt and rinse aid already in the dishwasher will not be used. - N.B.: even with the Flexi Tabs option selected, the regenerating salt/rinse aid lights will still stay on if their containers are empty. IMPORTANT: when no longer required, the option must be disabled by pressing the relative button (the light goes out). If the water hardness has been set on a value above H3, and the “Flexi Tabs” option is activated, the relative light flashes, warning of a setting error. 3in1 products are not suitable for use with very hard water; this does not prevent the use of the option, but the washing results might not be of the best. ULTRA CLEAN The ULTRA CLEAN program prolongs the final hot rinse to ensure a further reduction in the bacteria level. If the temperature in the tank falls during this stage of the program (e.g. because the door is opened or due to a power blackout), the light of the option and the program lights (2) flash to warn that the additional washing phase has not been completed successfully. This does not mean that the wash program has been less effective than usual.
User instructions 18 PROGRAM DELAY The start of the program can be delayed by 3, 6 or 9 hours. This allows you to set the dishwasher to work at the times of day most convenient to you. After setting the program, press the button to select the delay you require; the corresponding light will come on. When the door is closed, the appliance will prewash the dishes, after which the program delay set will come into effect. If you wish to exit the procedure without setting delayed start, press the button in sequence until all three lights are out. N.B.: It is not possible to select the PROGRAM DELAY option once the cycle has begun. CANCELLING THE CURRENT PROGRAM • To cancel the currently selected program open the door and hold down the PROGRAM SELECTION (3) button for a few seconds until the indicator lights for programs 4 and 5 illuminate simultaneously (marked end). • Close the door. • After approximately 1 minute the dishwasher will advance to the end of cycle. CHANGING THE PROGRAM To change the program in progress, simply open the door and select a new program. When the door is closed the dishwasher will automatically select the new program.