Smeg St337 Instruction Manual

							 
 
User instructions   
 
 29 
        ADJUSTING THE UPPER BASKET 
The  height  of  the  top  basket  can  be  adjusted  to  all ow  large  dishes  or 
pans to be placed in the bottom basket.  
The  adjustment  procedure  may  be  type  A  or  B,  depending  on  the 
dishwasher model purchased. 
           Version A: pull-out with adjustment in two positions. 
·   Pull out both the basket guides. 
·   Remove the stops, first releasing them as shown in  the diagram. 
·   Pull out the basket. 
·   Fit  the  upper  or  lower  pair  of  wheels  into  the  gui de,  depending  on 
the setting required
; 
·   Return the stops to their original position . 
The left hand and right hand sides of the basket  must always be set at 
the same height . 
 
  
            
Version B: with adjustment in three positions on both sides. 
The sides of the basket  must always be set at the same height . 
·   Raise the basket by pulling on the top edge  (1), to the first or second 
catch depending on the height required. 
·   To lower the basket, first release it by pulling t he release lever (2). 
Adjustment is also possible with the basket loaded,  but in this case when 
lowering  the  basket  it  should  be  held  steady  with  o ne  hand  to  avoid 
knocking the dishes. 
             
   
     
						

							 
 
User instructions   
  
30 
3.  Cleaning and maintenance  
 
Before carrying out any work, always unplug the app liance from the 
electrical supply or switch off the all-pole disconnection device. 
 
3.1  General warnings and recommendations   Avoid the use of acidic or abrasive detergents.  Clean  the  outer  surfaces  and  door-lining  of  the  dis hwasher  regularly 
using  a  soft  cloth  moistened  with  water  or  with  a  n ormal  detergent 
suitable  for  painted  surfaces.  Clean  the  door  gaske ts  with  a  damp 
sponge.  Periodically  (once  or  twice  a  year)  it  is  a dvisable  to  clean  the 
tank and gaskets, using a soft cloth and water to r emove any deposits. 
 CLEANING THE WATER INTAKE FILTER 
The  water  intake  filter A located  at  the  outlet  of  the  water  supply  tap 
needs to be cleaned periodically.  
After  having  closed  the  water  supply  tap,  unscrew  t he  end  of  the  water 
intake  hose,  remove  the  filter  A and  clean  it  delicately  under  running 
water.  Reassemble  filter  A in  its  seat  and  carefully  screw  the  water 
intake hose back into position. 
      CLEANING THE SPRAY ARMS 
The  spray  arms  can  be  easily  removed  for  periodic  c leaning  of  the 
nozzles,  to  prevent  possible  clogging.  Wash  them  un der  running  water 
and  carefully  replace  them  in  their  seats,  checking  that  their  rotary 
movement is in no way impeded . 
 ·  To remove the  upper spray arm, unscrew locking ring  R. 
·   To  remove  the  lower spray  arm,  simply  lift  it  up,  pulling  by  the 
central part. 
·   To  remove  the  orbital  spray  arm  assembly,  take  hold  of  the  longer 
arm  and  pull  the  orbital  unit  upward.  Wash  the  arms   under  a  jet  of 
running  water  and  return  them  carefully  to  their  se at. After 
reassembly,  check  that  the  spray  arms  turn  freely.  Otherwise, 
check that they have been installed correctly. 
    
               
ORBITAL 
            
						

							 
 
User instructions   
 
 31   CLEANING THE FILTER UNIT  ·  It  is  advisable  to  periodically  inspect  the  centre   filter C and,  if 
necessary,  to  clean  it.  To  remove  the  filter,  grip  the  tabs,  turn  them  
anticlockwise and lift upwards; 
·   push  the  centre  filter  D from  the  underside  to  remove  it  from  the 
micro-filter: 
·   separate  the  two  parts  which  make  up  the  plastic  f ilter  by  pressing 
the body of the filter in the zone shown by the arr ows; 
·   remove the centre filter by lifting it upwards. 
 
   
  
 GENERAL  WARNINGS  AND  RECOMMENDATIONS  FOR  CORRECT 
MAINTENANCE: 
·  The  filters  should  be  cleaned  under  running  water  using  a  stiff 
brush. 
·  When removing the filter , take care that there are no food residues 
on  it.  If  any  residues  fall  into  the  washing  pit  th ey  might  block 
hydraulic components, or foul the spray arm nozzles. 
·  It  is  essential  to  thoroughly  clean  the  filters   according  to  the 
above  instructions:  the  dishwasher  cannot  function  if  the  filters  are 
clogged. 
·  Carefully  replace  the  filters  in  their  seats,  to  avoid  damaging  the 
wash pump. 
 
PROLONGED DISUSE: 
·  Run the soak program twice in succession. 
·  Unplug  the power cord from the socket. 
·  Leave the door slightly open ,  in order to prevent the formation of 
unpleasant odours inside the washing tank. 
·  Fill the rinse aid dispenser . 
·  Shut off the water supply tap.     
      
						

							 
 
User instructions   
  
32  
  
 
BEFORE  STARTING  THE  DISHWASHER  AFTER  PROLONGED 
DISUSE: 
 
·  Check  that  there  are  no  deposits  of  sludge  or  rust  inside  the  water 
pipe: if there are, allow the water to run from the water supply tap for 
a few minutes. 
·  Plug the power cord  back into the socket. 
·  Reconnect the water intake hose and open the tap ag ain. 
 
 
 
TROUBLESHOOTING MINOR PROBLEMS 
 
In some cases it is possible to remedy minor problems by referring to the 
following instructions: 
 
If the program fails to start, check that: 
 
·  the dishwasher is connected to the electrical power  supply; 
·  there is no power failure; 
·  the water tap is open; 
·  the dishwasher door is properly closed. 
 
If water remains inside the dishwasher, check that:  
 
·  the drain hose is not kinked; 
·  the drain siphon is not obstructed; 
·  the dishwasher filters are not clogged. 
 
If the dishes are not being cleaned properly, check  that: 
 
·  the correct amount of detergent has been added; 
·  there is regenerating salt inside the special conta iner; 
·  the dishes are being loaded correctly; 
·  the  selected  program  is  suitable  for  the  dish  types   and  their  degree 
of soiling; 
·  all the filters are clean and positioned correctly;  
·  the spray arm nozzles are not obstructed; 
·  there is no object obstructing the rotation of the  spray arms. 
 
   
    
						

							 
 
User instructions   
 
 33  
  
 
If the dishes fail to dry or remain dull, check tha t: 
 
·  there is rinse aid inside the special container; 
·  the rinse aid dispenser setting is correct; 
·  the  detergent  used  is  of  good  quality  and  has  not  l ost  its 
effectiveness  (for  example,  through  incorrect  storage,  with  the  box 
left open). 
 
If the dishes show signs of streaking, staining, et c., check that: 
 
·  the rinse aid dispenser setting is not too high. 
 
If there are visible traces of rust inside the tank : 
 
·  the  tank  is  made  of  steel,  and  therefore  any  rust  m arks  are  due  to 
external  elements  (fragments  of  rust  from  the  water   pipes,  pots, 
cutlery, etc.). Special products are commercially available to remove 
such marks; 
·  check  that  the  amount  of  detergent  being  used  is  co rrect.  Certain 
detergents can be more corrosive than others. 
·  check  that  the  cap  of  the  salt  container  is  securel y  closed,  and  that 
the water softening setting is correct. 
      
 
  
 
If  after  following  the  above  troubleshooting  instru ctions  the  problem 
persists, call the nearest After-Sales Centre. 
 
WARNING:  any  operations  performed  on  the  appliance  by 
unauthorised persons are not covered by the warranty and shall be 
paid for by the user. 
 
  
   
     
						

							 
 
User instructions   
  
34 
4.  Troubleshooting 
 
  The  dishwasher  is  able  to  indicate  a  series  of 
malfunctions  by 
illuminating  a  number  of  lights  simultaneously  (see   key  below); “E”  or 
“Err”  (depending on the model) also appears on the displa y in the event 
of a malfunction.
 
 
FAULT DESCRIPTION 
E1  
Acquastop failure 
The  anti-flooding  system  has  been  activated  (for  th e 
relevant  models  only).  The  system  is  tripped  in  case 
of water leaks. Contact the after-sales service. 
E2  
Safety level 
The  system  which  limits  the  water  level  inside  the 
dishwasher  has  been  tripped.  Interrupt  the  program 
and switch off the dishwasher. Switch the dishwashe r 
back  on,  program  it  again  and  start  the  washing 
cycle.  If  the  problem  persists,  contact  the  after-sales 
service. 
E3  
Water heating malfunction 
The  water  is  not  heated  or  the  heating  parameters 
are  not  correct.  Repeat  the  washing  program;  if  the  
problem persists, contact the after-sales service. 
E4  
Water temperature monitoring malfunction 
Interrupt  the  program  and  switch  off  the  dishwasher. 
Switch the dishwasher back on, program it again and  
start  the  washing  cycle.  If  the  problem  persists, 
contact the after-sales service. 
E5  
Water intake malfunction 
The  appliance  does  not  take  in  water  or  does  not  do 
so  correctly.  Check  that  the  water  connections  are 
correct, the water intake tap is turned on and the filter 
is  not  fouled.  If  the  problem  persists,  contact  the  
after-sales service. 
E6  
Water pump-out malfunction 
The  appliance  does  not  pump  out  the  water  or  does 
not  do  so  correctly.  Check  that  the  drain  hose  is  not 
kinked  or  crushed  and  that  the  siphon  and  filter  ar e 
not  fouled.  If  the  problem  persists,  contact  the  after-
sales service. 
   
         
						

							 
 
User instructions   
 
 35 
 
FAULT DESCRIPTION 
E7  
Turbine flow-regulator malfunction  
(for the relevant models only)  
The appliance is not able to measure the amount 
of  water  loaded  accurately.  Interrupt  the  program 
and  switch  off  the  dishwasher.  Switch  the 
dishwasher  back  on,  program  it  again  and  start 
the  washing cycle.  If  the  problem  persists, contact  
the after-sales service. 
E8  
Alternate washing system malfunction 
Interrupt  the  program  and  switch  off  the  dishwasher. 
Switch the dishwasher back on, program it again and  
start  the  washing  cycle.  If  the  problem  persists, 
contact the after-sales service. 
E9  
Water intake system malfunction 
Contact the after-sales service. 
   
  Light off   Light on 
   Light flashing 
   
If  an  alarm  occurs  the  appliance  interrupts  the  pro
gram  in  progress  and 
signals a fault. 
 ·  Alarms  E1,  E2,  E3,  E4,  E8  and E9  interrupt  the  current  program 
immediately. 
·  The  E5, E6   alarms  interrupts  the  running  program  once  the  cau se  is 
resolved, it will bring bach the execution of the p rogram. 
· The alarm  E7 is visualized at the end  of the cycle that comes,  however, 
brought to the end since the operation of the dishw asher is not harmed. 
 To “reset” an alarm is necessary:  · Open and close the door, or turn off and on the mac hine. At this point is 
possible to program the dishwasher again.  
   
 
   If the malfunction persists, contact your authorise d Service Centre.  
    
       
						

							 
 
User instructions   
  
36 
  
TECHNICAL DATA  
Width 597 ¸ 599 mm 
Depth measured flush with the  outer edge of the control panel 550 mm 
Height (depending on models) from 820 mm to 890 mm from 860 mm to 930 mm 
Capacity 14 Standard place settings 
Water supply pressure min. 0,05 - max. 0,9 MPa (min. 0.5 – max. 9 bar) 
Electrical characteristics See rating plate