Smeg Sc485x-8 Manual

Cleaning and maintenance
73
EN
•  For Multifunction models and models 
with Pizza plate: Spray a water and 
washing up liquid solution inside the 
oven using a spray nozzle. Direct the 
spray against the side walls, upwards, 
downwards and towards the deflector.
•  Close the door.
•  During the assisted cleaning cycle, wash 
the self-cleaning panels (where fitted) 
which were previously removed 
separately in warm water and a small 
amount of detergent.Vapor Clean setting
1. Press and turn the function...

Cleaning and maintenance
74
4. At the end of the Vapor Clean cycle, 
STOP flashes on the display and a 
buzzer will sound that can be 
deactivated by pressing the function 
knob.
Setting timed Vapor Clean
It is possible to program the Vapor Clean 
start time, like any cooking function.
1. After selecting the Vapor Clean function, 
press the programming knob. The 
display will show the current time and the 
temperature, and the   indicator light 
will come on.
2. Turn the programming knob to set the 
time...

Cleaning and maintenance
75
EN
4.6 Pyrolytic function (on some 
models only)
Preliminary operations
Before starting the pyrolytic cycle:
•  Clean the internal glass pane following 
the usual cleaning instructions.
•  For very stubborn encrustations spray an 
oven cleaning product onto the glass 
(read the warnings on the product); 
leave for 60 minutes, then rinse and dry 
the glass using kitchen roll or a microfibre 
cloth.
•  Completely remove all accessories from 
inside the oven.
•  Remove the...

Cleaning and maintenance
76
Pyrolytic cycle
1. Two minutes after the Pyrolytic cycle 
starts, the   indicator light comes on to 
indicate that the door is locked by a 
device that prevents the door from being 
opened.
2. At the end of the Pyrolytic cycle, STOP 
flashes on the display and a buzzer will 
sound that can be deactivated by 
pressing the function knob.
3. The door remains locked as long as the 
temperature inside the oven returns to 
safety levels. Wait for the oven to cool 
down (the...

Cleaning and maintenance
77
EN
Setting of a programmed Pyrolytic cycle
It is possible to program the pyrolytic cycle 
start time like all other cooking functions.
1. After selecting the Pyrolytic function and 
setting the duration (except for Eco 
Pyrolytic), press the programming knob. 
The display will show the current time 
and the temperature, and the   
indicator light will come on.
2. Turn the programming knob to set the 
time you wish the Pyrolytic cycle to finish.
3. Press the programming knob to...

Cleaning and maintenance
78
4. Slide out and remove the lamp.
5. Replace the lamp with one of the same 
type (40W).
6. Refit the cover. Ensure the moulded part 
of the glass (A) is facing the door.
7. Press the cover completely down so that 
it attaches perfectly to the bulb support.Removing and fitting the oven seal 
(pyrolytic models excluded)
To  r e m o v e  t h e  o v e n  s e a l :
•  Unhook the clips in the 4 corners then 
pull the oven seal outwards.
To install the oven seal:
•  Hook the clips in...

Installation
79
EN
5 Installation
5.1 Electrical connection
General information
Check the grid characteristics against the 
data indicated on the plate.
The identification plate bearing the 
technical data, serial number and brand 
name is visibly positioned on the appliance.
Do not remove this plate for any reason.
The appliance works at 220-240 V~.
Use an H05V2V2-F type three-core cable 
(3 x 1.5 mm
2 cable, referring to the cross 
section of the internal conductor).
Perform the earth/ground connection...

Installation
80
5.3 PositioningFastening bushings
1. Remove the bushing covers inserted on 
the front of the appliance. 
2. Mount the appliance into the recess.
3. Secure the appliance to the piece of 
furniture using screws.
4. Cover the bushings with the covers 
removed previously.
Heavy appliance
Crushing hazard
•  Position the appliance into the cabinet 
cutout with the help of a second person.
Pressure on the open door
Risk of damage to the appliance
•  Never use the oven door to lever the...

Installation
81
EN
Appliance overall dimensions (mm) 

Installation
82
Mounting under worktops (mm) Mounting into a column (mm)
Make sure that the piece of 
furniture rear/bottom part has an 
opening of approx. 60 mm.
Make sure that the piece of 
furniture top/rear part has an 
opening approx. 35-40 mm deep.