Smeg Sa310x 5 User Manual

Cleaning and maintenance
21
EN
4 Cleaning and maintenance
4.1 Instructions
4.2 Cleaning the surfaces
To keep the surfaces in good condition, 
they should be cleaned regularly after use. 
Let them cool first.
4.3 Ordinary daily cleaning
Always use only specific products that do 
not contain abrasives or chlorine-based 
acids.
Pour the product onto a damp cloth and 
wipe the surface, rinse thoroughly and dry 
with a soft cloth or a microfibre cloth.
4.4 Food stains or residues
Do not use metallic sponges...

Cleaning and maintenance
22
3. To reassemble the door, put the hinges in 
the relevant slots in the oven, making sure 
that grooved sections A are resting 
completely in the slots. Lower the door 
and once it is in place remove the pins 
from the holes in the hinges.
4.6 Cleaning the door glazing
The glass in the door should always be kept 
thoroughly clean. Use absorbent kitchen 
roll. In case of stubborn dirt, wash with a 
damp sponge and an ordinary detergent.
4.7 Removing the internal glass 
panels...

Cleaning and maintenance
23
EN
4. Clean the external glass panel and the 
panels previously removed. Use 
absorbent kitchen roll. In case of 
stubborn dirt, wash with a damp sponge 
and neutral detergent.
5. Refit the panels in the reverse order in 
which they were removed.
6. Reposition the internal glass panel. Take 
care to centre and insert the 4 pins into 
their housings in the oven door by 
applying slight pressure.4.8 Cleaning the inside of the oven
For the best oven upkeep, clean it regularly...

Cleaning and maintenance
24
Removing racks/trays support frames
Removing the guide frames enables the 
sides to be cleaned more easily. This 
operation should be performed each time 
the automatic cleaning cycle is used (on 
some models only).
To remove the guide frames: Pull the frame 
towards the inside of the oven to unhook it 
from its groove A, then slide it out of the 
seats B at the back.
When cleaning is complete, repeat the 
above procedures to put the guide frames 
back in.4.9 Vapor Clean:...

Cleaning and maintenance
25
EN

solution inside the oven using a spray 
nozzle. Direct the spray against the side 
walls, upwards, downwards and 
towards the deflector.

Vapor Clean setting
1. Turn the function knob and the 
temperature knob to the   symbol.
2. Set a cooking time of 18 minutes using 
the cooking time procedure described in 
more detail in “Programmed cooking”;
3. The Vapor Clean cycle starts 
approximately 6 seconds after the last 
pressure on the programmers keys.4. At the end of the...

Cleaning and maintenance
26
4.10 Pyrolysis: automatic oven 
cleaning (on some models only)
Preliminary operations
Before starting the pyrolysis cycle:

the usual cleaning instructions.

oven cleaning product onto the glass 
(read the warnings on the product); 
leave for 60 minutes, then rinse and dry 
the glass using kitchen roll or a microfibre 
cloth.

inside the oven.

present).

Pyrolysis setting
1. Turn the function knob to symbol   or 
.
2. Press the temperature knob to start the 
pyrolysis cycle....

Cleaning and maintenance
27
EN
Pyrolysis
5. The display shows “Pyro” to indicate that 
the appliance is carrying out the 
automatic cleaning cycle.
6. Two minutes after the pyrolysis cycle has 
started the door is locked (the door lock 
indicator light   comes on) by a device 
that prevents the door from being 
opened.
7. Press the temperature knob to display the 
time remaining to the end of the pyrolysis 
cycle.
8. At the end of the pyrolysis cycle, the door 
remains locked as long as the 
temperature...

Cleaning and maintenance
28
4.11 Extraordinary maintenance
Replacing the internal light bulb
1. Completely remove all accessories from 
inside the oven.
2. Remove the racks/trays support frames.
3. Remove the bulb cover using a tool (e.g. 
a screwdriver).
Incandescent lamps:
4. Unscrew and remove the lamp.
5. Replace the lamp with one of the same 
type (25W).6. Refit the cover correctly, so that the 
moulded part of the glass is facing the 
door.
7. Press the cover completely down so that 
it attaches...

Cleaning and maintenance
29
EN
Removing the door seal (not on pyrolytic 
models)
To permit thorough cleaning of the oven, the 
door seal may be removed. There are 
fasteners on all four sides to attach it to the 
edge of the oven. Pull the 4 edges of the 
seal outwards to detach the fasteners.
What to do if...
The display is completely off:


upstream of the appliance supply line is 
in the “ON” position.
The appliance does not heat up:

“showroom” mode (for further details see 
“Secondary menu”).
The...

Installation
30
5 Installation
5.1 Electrical connection
General information
Check the grid characteristics against the 
data indicated on the plate.
The identification plate bearing the 
technical data, serial number and brand 
name is visibly positioned on the appliance.
Do not remove this plate for any reason.
The appliance works at 220-240 V~.
Use a H05V2V2-F type three-core cable (3 
x 1.5 mm
2 cable, referring to the cross 
section of the internal conductor).
Perform the ground connection using a...