Smeg Sa304x-8 User Manual

Instructions for the User
41 •  Spray a water and washing up
liquid solution inside the oven using
a spray nozzle. Aim the spray
towards the side walls, roof, floor
and deflector (the coloured zone on
the illustration to the side shows
where the solution can be sprayed).
Do not spray excessive amounts of the water and washing up liquid solution.
We recommend spraying approx. 20 times at the most.
•  Close the door and set the assisted
cleaning cycle.
8.7.2 Setting the assisted cleaning cycle
Turn the...

Instructions for the User
428.7.3 End of the assisted cleaning cycle
The water remaining at the end of the assisted cleaning cycle cannot be left
inside the oven for long (for example overnight).
You are advised to wear a pair of gloves during these processes.
At the end of the cleaning cycle, open the door and wipe away the less stubborn
dirt with a microfibre cloth. Use an anti-scratch sponge with brass filaments on
more difficult encrustations (we recommend removing the door to facilitate
access to...

Instructions for the User
43
9. EXTRAORDINARY MAINTENANCE
The oven may require extraordinary maintenance or replacement of parts
subject to wear such as gaskets, bulbs, etc. The following instructions describe
how to carry out these minor maintenance operations.
Before any intervention that requires access to live parts, disconnect the
power supply of the appliance.
9.1 Replacing the light bulb
If a light bulb needs to be replaced because it is worn or burnt out (in
multifunction models remove the guide...

Instructions for the User
44
9.2 Removing the door
9.2.1 With moveable levers
Open the door completely.
Lift the levers A of the two hinges away
from them until they engage.
Grasp the door on both sides with both
hands, lift it forming an angle of around
30° and remove it.
If the hinges have not unlocked, repeat
the operation, raising the levers A and
keeping the door slightly raised.
To reassemble the door, put the hinges
in the relevant slots in the oven, making
sure that the grooved sections C are...

Instructions for the User
45
9.2.2 With pins
Open the door completely.
Insert two pins into the holes indicated
A in the two hinges towards the back of
them until they engage.
Grasp the door on both sides with both
hands, lift it forming an angle of around
30° and remove it.
To reassemble the door, put the hinges
in the relevant slots in the oven, making
sure that the grooved sections C are
resting completely in the slots.  Lower
the door and once it is in place remove
the pins from the holes in the...

Instructions for the User
46
9.3 Removing the door seal
For multifunction models only:
To permit thorough cleaning of the
oven, the door seal may be removed.
There are fasteners on all four sides to
attach it to the edge of the oven. Pull
the edges of the seal outwards to
detach the fasteners.
9.4 Removing the internal glass panels
The glass in the door should always be kept thoroughly clean. To facilitate
cleaning, it is possible to remove the door (see 9.2 Removing the door) and
place it on a canvas,...

Instructions for the User
47
Removing the internal glass panel:
•  Remove the internal glass panel by
pulling it upwards, following the
movement indicated by the arrows. Doing
this detaches the 4 pins attached to the
glass from their slots in the oven door.
Removing the middle glass panels:
(pyrolytic models)
•  There are two middle glass panels in
pyrolytic models, attached using 4 small
locks. Remove the middle panels by lifting
them upwards.
(Multifunction models)
•  Multifunction models have a single...

Instructions for the User
48
10.INSTALLING THE APPLIANCE
10.1 Electrical connection
The identification plate bearing the technical data, serial number and brand
name is visibly positioned on the appliance.
Do not remove this plate for any reason.
The appliance must be connected to earth in compliance with electrical system
safety regulations.
If a fixed connection is being used, fit the power line with an omnipolar circuit-
breaker in accordance with the installation rules, located in a position which...

Instructions for the User
49
10.3 Positioning the oven
Never use the oven door to lever the oven into place when fitting. Avoid exerting
too much pressure on the door when open.
We recommend installing the oven with the help of a second person.
The base on which the oven is resting must be complete as shown in the
illustrations below.
The oven is designed for mounting into any piece of furniture as long as it is
heat-resistant (90°C).
Proceed according to the dimensions shown in Figures 1, 2 and 3.
For...

Instructions for the installer
50
When installing in tall units, comply with the dimensions shown in figures 1 and
2, bearing in mind that the top/rear of the unit must have an opening 35-40 mm
deep. 
Remove the screw covers on the frame and screw in the 2 screws A (fig. 5) to
fix the appliance to the unit. Replace the screw covers. For installing beneath a
countertop hob, allow for a rear and bottom clearance as shown in Figure 1 (ref.
F).
See the relevant instructions for fitting and securing the...