Smeg Sa304x-8 Manual

Instructions for the User
31
RUNNER POSITION 
FROM BOTTOMTEMPERATURE
°CTIME IN MINUTES
12808
2190 - 20030 -35
2180 - 19015 -20
2 160 - 170 50 - 55
2 160 - 170 30 - 35
2 170 35 - 40
2 160 - 170 20 - 25
2 170 20 - 25
2 160 - 170 50 - 60
2 170 50 - 60
2 150 - 160 40 - 50
2 150 - 160 45 - 50
2 160 40 - 50
2 170 50 - 60
2 160 25 - 30
3180 60 

Instructions for the User
32
7.4 Proving and defrosting functions 
On pyrolytic models only:
The special defrosting and proving functions are brought together under the
same function indicated by  .
The choice of temperature determines whether defrosting or proving takes place
based on the table below.
Temperature 
(°C)FunctionRunner position 
from the bottomTime in 
minutes
30 Defrosting 1
Depending on 
the quantity
40 Proving 1 

Instructions for the User
33
8. CLEANING AND MAINTENANCE
NEVER USE A STEAM JET FOR CLEANING THE APPLIANCE.
We recommend the use of cleaning products distributed by SMEG.
8.1 Cleaning stainless steel
To keep stainless steel in good condition it should be cleaned regularly after
use. Let it cool first.
8.2 Ordinary daily cleaning
To clean and preserve the stainless steel surfaces, always use only specific
products that do not contain abrasives or chlorine-based acids.
How to use: pour the product onto a...

Instructions for the User
34
8.5 Cleaning the inside of the oven
For the best oven upkeep, clean it regularly after having allowed it to cool. 
•  Take out all removable parts.
•  Clean the oven racks with hot water and non-abrasive detergent. Rinse and
dry.
•  For easier cleaning, the door can be removed (see “9.2 Removing the
door”).
The oven should be operated at the maximum heat setting for 15/20 minutes
after use of specific products, to burn off the residues left inside the oven. 

Instructions for the User
35 On pizza models only, to clean the bottom of the oven, the following operations
have to be carried out first:
Remove the cover then the base on which it is resting. The base must be lifted a
few millimetres, then pulled outwards.
Ovens with frames Ovens with runners
Lift up the edge of the lower heating element a few centimetres and clean the
bottom.
Put the pizza plate support back in place, pushing it in until it hits the back of the
oven, and push it down so that the...

Instructions for the User
368.5.1 Removing guide frames
Removing the guide frames makes it
easier to clean the side parts, and it
also needs to be done whenever the
automatic cleaning cycle is used (only
available on some models).
•  To remove the guide frames, pull
the frame towards the inside of the
oven to unhook it from its housing
A, then slide it out of the seats at
the back B.
•  When cleaning is complete, repeat
the above procedures to put the
guide frames back in. 

Instructions for the User
37
8.6 Pyrolysis: automatic oven cleaning (on some models only)
Pyrolysis is an automatic high-temperature cleaning procedure which causes
dirt to dissolve. Thanks to this process, it is possible to clean the inside of the
oven very easily.
During the first automatic cleaning cycle, unpleasant smells may occur due to
the normal evaporation of oily manufacturing substances. This is an absolutely
normal phenomenon which disappears after the first cleaning cycle.
Before starting...

Instructions for the User
388.6.1 Before starting the automatic cleaning cycle
Pyrolysis may be carried out at any time of the day or night (if you wish to
benefit from the lower cost of electricity overnight).
•  Completely remove all accessories
from inside the oven and the roof
lining, as shown in the illustration.
•  Make sure that the oven door is
firmly closed.
Refer to the following diagram for setting the cleaning cycle duration:
CLEANING
DURATION
LIGHT DIRTMEDIUM DIRTHEAVY DIRT
90 MIN. 135 MIN....

Instructions for the User
39
8.6.2 Setting the cleaning cycle
Turn the function selection knob to select one of the
two cleaning cycles out of   and  .
To start the cleaning cycle (Pyrolysis), press 
followed by  .
Press and hold  ; press   or   to set the
duration of the cycle between a minimum of 1h 30m
and a maximum of 3h 00m (apart from the   cycle
where the duration is set at 1h 30m).
Two minutes after the cleaning cycle (Pyrolysis)
starts, a locking device which prevents opening of
the door will be...

Instructions for the User
40
8.7 VAPOR CLEAN: assisted oven cleaning (on some models only)
VAPOR CLEAN is an assisted cleaning procedure which facilitates the removal
of dirt. Thanks to this process, it is possible to clean the inside of the oven very
easily. The dirt residues are softened by the heat and water vapour for an easier
removal afterwards.
Before starting the assisted cleaning cycle, make sure that the oven does not
contain any foods or large spills from previous cooking operations.
Carry out...