Singer Serger Professional 5 Manual

 
   
 Two-Thread Overedge (narrow) page 6
 
 
  

 
   
 Two-Thread Overedge (narrow) page 7
 
 
  
  3. Thread the top cover thread guide by pu lling the thread towards the left until    
                it slips under the guide.  Then pull the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
  4. While holding the thread firmly,  pull the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
   
  5. Turn the handwheel toward you unt il the lower looper extends 5-10mm  
       (approximately ½”) from the needl e plate...

 
 Two-Thread Overedge (narrow) page 8
 
 
 10. Thread the looper eye (A)  from front to back.  Pull about 4 inches of thread. 
                 Position thread into V cutout (B) on thr eader.  Firmly hold thread tail with left   
                  hand and pull Threader Lever (C) up into place (D).  
 
 
 
 
   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 Two-Thread Overedge (narrow) page 9
 
 
  
  3. Thread the top cover thread guide by  pulling the thread towards the left until 
       it slips under the guide.  Then pu ll the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
 
 
  4. Continue to thread point s 4-8.  Slip the thread into the rear slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the right  slot of the thread guides i and  j....

 
  
Two-Thread Overedge (wide) 
 
        
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                  
 
 
 
 
 
 
 
 
The Two-Thread Overedge (wide) is a good choice when sewing linens and wools.  
The Two-Thread Overedge (wide) has the sa me set up as the Two-Thread Over-
edge (narrow) Stitch.  The  only exception is the Right
 Overedge Needle is now un-
threaded and removed and the Left
 Overedge Needle is threaded.  By  
using the left needle the...

 
 
ATD: 
Auto Tension Dial  
         “E” 
Left Cover Stitch 
Needle “C” (Orange) Unthreaded and 
Remove Needle 
Middle Cover Stitch 
Needle “D” (Blue) Unthreaded and 
Remove Needle 
Right Cover Stitch 
Needle “E” (Green) Unthreaded and 
Remove Needle 
Overedge Left  
Needle “A” (Orange)    Threaded 
Overedge Right  
Needle “B” (Blue) Unthreaded and 
Remove Needle   
Upper Looper 
(Green)  Engage Looper 
and Not Threaded 
Lower Looper 
(Red)      Threaded 
Chain Stitch Looper 
(Brown)    Not Threaded...

 
   
  
 
  5. Continue to thread point s 4-8.  Slip the thread into the middle slot of the  
      thread guide  g.  Go over the take up lever  h.  Continue by slipping the  
               thread into the middle  slot of the thread guides i and  j.  
 
  6. Before threading the eye of the needl e, make sure the thread is behind
   
               the thread guide located on the  bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
  7. Thread the eye of the Left Overedge Needle  k....