Singer Professional 5 Manual

							 
  
  3. Thread the top cover thread guide by pulling the thread towards the left until    
                it slips under the guide.  Then pull the thread along the right side of the  
       button as illustrated. 
 
 
 
 
 
 
 
  4. While holding the thread firmly, pull the thread between the tension disks. 
 
 
  
 
 
 
 
 
 
  
  5. Turn the handwheel toward you until the lower looper extends 5-10mm  
       (approximately ½ inch) from the needle plate edge.  
 
  6. Thread the looper area of the machine following the red color coded  
       thread guides 4-10. 
 
  
 7. Place the thread slighty from left and  
      to the right of threading guide f. 
 
 
 
  
 
  8. Place the thread slightly from the  
               front and to the back of threading 
               guide g. 
 
 
 
 
   9. Place the thread through h, i,and j. 
  
 
Two-Thread Wrapped Edge Overlock (narrow) page 7  
						

							 
 10. Thread the looper eye (A) from front to back.  Pull about 4 inches of thread. 
                 Position thread into V cutout (B) on threader.  Firmly hold thread tail with left   
                 hand and pull Threader lever (C) up into place (D).  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
  
 

						

							 
  
  3. Thread the top cover thread guide by pulling the thread towards the left until 
       it slips under the guide.  Then pull the thread along the right side of the  
       button as illustrated.  
 
 
 
 
 
 
 
 
 
  4. Continue to thread points 4-8.  Slip the thread into the rear slot of the  
      thread guide g.  Go over the take up lever h.  Continue by slipping the  
               thread into the right slot of the thread guides i and j.  
 
  
 
 
 
 
 
 
 
 
 
 
 
  
  5. Before threading the eye of the needle, make sure the thread is behind
   
               the thread guide located on the bottom of the needle clamp. 
 
 
 
 
 
 
 
  
  
 
 
  
  6. Thread the eye of the Right Overedge Needle k. 
 
   6 
Two-Thread Wrapped Edge Overlock (narrow) page 9  
						

							 
  
Two-Thread Wrapped Edge Overlock (wide) 
 
    Needle
:      
  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
      
 
                         
 
 
 
 
 
 
 
 
                                 
 
 
 
 
 
 
 
 
ATD: 
Auto Tension Dial  
           “D” 
Left Cover Stitch 
Needle (Orange) Unthreaded and 
Remove Needle 
Middle Cover Stitch 
Needle (Blue) Unthreaded and 
Remove Needle 
Right Cover Stitch 
Needle (Green) Unthreaded and 
Remove Needle 
Overedge Left Needle 
(Orange)      Threaded 
Overedge Right Needle 
(Blue) Unthreaded and 
Remove Needle 
Upper Looper 
(Green)  Looper Engaged 
and Not Threaded 
Lower Looper 
(Red)      Threaded 
Chain Stitch Looper 
(Brown)    Not Threaded 
Upper Knife      Engaged 
Seam Guide Plate    Not Installed 
Use Knife Cover 
Seam Width Dial           “N” 
Stitch Length Dial           “2” 
Presser Foot  
Pressure           “N” 
Differential Feed Dial            “N” 
Stitch Finger           “N” 
Spreader       Engaged 
The Two-Thread Wrapped Edge Overlock (wide) has the same set up as the Two-
Thread Wrapped Edge Overlock (narrow) Stitch.  The only exception is the Right 
Overedge Needle is now unthreaded and removed and the Left 
 Overedge Needle 
is threaded.  By using the left needle the stitch becomes wider.  
Left Overedge Needle Thread  
 Right Overedge Needle 
Thread  
Two-Thread Wrapped Edge Overlock (wide) page 1 
   Set at:  
						

							 
  
 
  5. Continue to thread points 4-8.  Slip the thread into the middle slot of the  
      thread guide g.  Go over the take up lever h.  Continue by slipping the  
               thread into the middle slot of the thread guides i and j.  
 
  6. Before threading the eye of the needle, make sure the thread is behind
   
               the thread guide located on the bottom of the needle clamp. 
 
 
 
 
 
 
 
 
 
 
 
 
 
    
 
 
 
 
 7. Thread the eye of the Left Overedge needle k. 
 
  8. Draw about 4 inches of the thread through the needle eye towards the back 
      of the machine.  
  
      9. Place the thread to the back, under the Presser Foot.   
 
 
 
 
 
 
Two-Thread Wrapped Edge Overlock (wide) page 3