Sim2 Multimedia Projector Proc3 User Manual

11
proc3

+12VUSB 1.1R/CrCONTROL (RS232)GRAPHICS RGBC/YB/CbHVS-VIDEOAUDIO OUTHDMI 1REMOTE32S-VIDEOMENUESCINPUT154
0IHDMI 26

To  activate  an  electric  motorised  screen  a  12  Volt  output  is 
provided at the rear of the projector (Fig. 8).
The output is activated (Voltage: 12 Vdc) when the projector is 
switched on and is de-activated (no Voltage output) when the 
projector is in stand-by mode.
You can also use black motirised curtains to delimit the screen 
when the projected image aspect ratio...

12
proc3

6   SWITChING ThE PROJECTOR ON AND OFF
WARNING: Connect the projector to a power supply with a 
nominal voltage within the following values: 100-240 V AC, 
50/60 hz. It must be earthed (Fig. 10).
GRAPHICS RGBHVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
2S-VIDEO
MENU
ESCINPUT
1
5
4
0I
Power Switch:Position I: OnPosition 0: Off
FusedPower Socket
Power Plug
 
Fig. 10
In position I the projector will initialise itself  (red and green leds 
on) and then goes into standby mode (red led on) (Fig. 11).
HDMI 1...

13
proc3

SWITChING OFF AND RETURNING TO STANDBY
With the remote control: press  .
With the keypad: press .
When switching off, the projector goes into stand-by mode and 
stores the input selection at the time of switch-off.
The  fans  keep  running  until  the  lamp  cools  down  (green  and 
red leds on), after which they automatically switch off. Do not 
switch off the projector with the power switch until the fans have 
stopped running.  
7  CONNECTIONS
To obtain the best performance from your...

14
proc3

Pro-C3 - Connection panel 
31245
Television receiver
DVD player
VCR
Videocamera
Video game console
Television receiver
HDTV receiver
DVD player
VCR
Video game console
ComputerDVD player
HDTV receiver
Fig.14
6
+12V
USB 1.1R/Pr
CONTROL (RS232)GRAPHICS RGB
C/YB/Pb HVS-VIDEO
AUDIO OUT
HDMI 1
REMOTE
3 
2 S-VIDEO
MENU
ESCSOURCE
1 
 
4 
 O I 
 
1 VIDEO 
GRAPHICS RGB - YPrPb4 
3 RGB - YPrPb 
HDMI 5 
HDMI 6 
5 
2 S-VIDEO
HDMI 26   

15
proc3

Fig.14
of the pictures reproduced by the Pro-C3 in the two cases:  the 
deinterlacing performed by the Pro-C3 is often more effective 
than that performed by the source itself.
GRAPhICS RGB - YPrPb
This input should be connected to an RGB-type video or graphic 
signal using a cable with a DB15HD type connector.
The signal source device (typically a personal computer or game 
console) must be able to provide separate H/V synchronisation or 
composite H+V synchronisation.
hDMI™
HDMI™  (High...

16
proc3

RS232 INTERFACE CONNECTOR 
The projector can be controlled from a PC: simply hookup 
the interface connector to a PC ’s RS232 serial cable or to a 
PC's USB 1.1 cable.
Do  not  place  objects  between  the  remote  control  and  the 
receiver on the projector, as this can prevent the remote from 
working.
764# 
 3$S$0 /530 -
	 3 4 
(3 1)* $4
 3( #$:#$ C)747*%&0 6%*0 
0 65) %.*
 3&.05&47*%&0. &/ 6&4$*/ 165)% .*
0I
12
MOTORISED SCREEN OUTPUTS
+12V
USB 1.1R/Cr
CONTROL...

17
proc3

MAIN MENU
To  access  the  main  menu  of  the  On  Screen  Display  press 
the MENU key on the keypad or the MENU+ or MENU- key on the 
remote control. 
The  main  menu  is  divided  into  four  windows, PICTURE,  IMAGE, 
SETUP  and  MENU,  in  which  the  various  adjustments  are  grouped 
according to the frequency of use. Use the ▲ and ▼ keys to 
select  the  line  corresponding  to  the  adjustment  you  wish  to 
make (Fig. 19). 
The  various  menus  only  offer  the  relevant...

18
proc3

To  access  these  submenus,  press  the  

19
proc3

NORMAL:  projects  the  image  occupying  the  full  height  of  the 
screen  while  maintaining  the  aspect  ratio  of  the  input  signal. 
When the input signal aspect ratio is 4:3 black vertical bands 
are displayed on the right and left of the picture.
ANAMORPHIC: correctly displays a 16:9 image.
LETTERBO x: serves to display a 4:3 letterbox image (with source 
signal having black bands above and below the picture) so that 
it fills the 16:9 screen and maintains the correct aspect ratio....

20
proc3

There  are  4  sets  of  gamma  curves:  Standard  (ST),  Enhanced SIM2  (EN)  and  Graphics  (GR),  User.  The  Standard  curve  has been  defined  for  general  use,  and  is  set  for  videocameras, digital cameras, and for viewing films or photos on your PC. The Enhanced set is suitable for watching movies. The Graphics set is suited to displaying synthetic graphics (PC, CAD, PC presenta-tions, etc.). User enables you to define your own curve. You can thus select the coefficient which...