Sim2 Multimedia Ht300 Xtra Projector User Manual

User and Installation Manual
The home theater projector
HT300 XTRA
cod.46.0328.000 

LIGHT
F1ZOOM
FOCUSF2
Not active
in this model.
Not active
in this model. MENU -
Activates  the On Screen
Display menus.
Navigates menu pages.
FREEZE
Freezes a moving
picture.STAND-BY
Switches off to stand-by.
0-9 Keys
Switch on from stand-by
and allow direct source
selection.
ESCAPE
Deactivates the On Screen Display.
MENU +
Activates  the On Screen Display menus.
Navigates menu pages.
INFO
Displays the selected source information 
and the projector status.
VCR
Improves the video recorder
signals...

1
XTRA
1   INTRODUCTION
Congratulations and thank you for choosing the  HT 300
XTRA, a SIM2 Multimedia SpA product 
(Fig. 1).
C
-
S
Y
N
CD
V
I 

2
XTRA
A sophisticated proprietary optical system, coupled with a hight
performance zoom lens ensures hight contrast images, superior
uniformity and edge-to-edge definition.
A new 6-segment colour wheel dramatically reduces the so
called “rainbow effect” and gives a better contrast, better
colorimetry and a lower black level to the image.
The new HD2+ DMD™ chip ensures, on top of the high definition
resolution (1280 x 720 pixels), an increased contrast ratio of >
2800:1 thus delivering on the screen an...

3
XTRA
1 Projection lens
2 Lens shift knob
3 Cooling air inlet vents
4 Remote control IR sensor
5 Cooling air outlet vents
6 Adjustable carry-handle
7 Adjustable levelling feet
8 Ceiling/wall bracket fixing holes
64
12358
7
C-SYNCDVI
12111317
9
10
2216
20
15
14
1821
19
9 Fused power socket
10 Main power switch
11 Remote control rear IR sensor
12 Green LED
13 Red LED
14 Rear keyboard pad
15 Composite video input
16 S-Video input
17 VGA input
18 RGB / YCrCb input
19 DVI-D
20 12Vdc screen output
21 RS232...

4
XTRA
!
CAUTION
RISK OF ELECTRIC SHOCK!
DO NOT REMOVE THE TOP COVER
Prior to switching on the projector please read each chapter of this manual carefully as this manual provides basic
instructions for using the projector.
The installation of the lamp assembly, preliminary adjustments and procedures that necessitate the removal of the
top cover, must be carried out by authorised, trained technicians. There are no user serviceable parts inside. To
ensure safe and long term reliability please use power...

5
XTRA
Please follow carefully the warnings listed below, to ensure safe
and long term performance of your projector.
• Connect the projector to a power supply with a nominal
voltage within the following values: 100-240 Vac, 50/60 Hz,
earthed 
(Fig. 3).
100-240 Vac50/60 Hz
DVI
Fig. 3
• The mains plug is the disconnect device. Take care, when
installing, that the mains plug and socket outlet are easily
accessible. Never pull on the cable to take it out of the socket.
If the system is unlikely to be used...

6
XTRA
3   PACKAGING AND CONTENTS
To unpack the projector safely and easily please follow steps 1
to 4, as per drawing 
(Fig. 5).
It is recommended that the carton and packaging is retained
for future use and in the unlikely event that your projector needs
to be returned for repair. The carton should contain the following:
- the projector
- the remote control
- four 1.5V AAA batteries (for remote control)
- three power cables (EU, UK, USA)
- the user manual.
Fig. 5
1234
• Take care not to shake the...

7
XTRA
Position the projector on a stable, suitable platform or utilise
the optional bracket for a fixed ceiling or wall installation.
CAUTION: In the case of ceiling or wall mounting
using a suspension bracket, follow the instructions
carefully and comply with the safety standards you
will find in the box together with the bracket. If you
use a bracket different to the one supplied by SIM2
Multimedia, you must make sure that the projector
is at least 65 mm (2-9/16 inch) from the ceiling and
that the...

8
XTRA
KEYSTONE
20%
C-SYNCDVI
Fig. 9
The Orientation adjustment in the Set up menu will allow the
projector to be used for desktop front, ceiling front, desktop
rear and ceiling rear installations 
(Fig. 10).
C-SYNCDVI
Fig. 10
To activate an electric motorised screen a 12 Volt output is
provided at the rear of the projector or with the optional Remo-
te Input Interface.  This can be connected to a screen interface
unit, which can be supplied by screen manufacturers 
(Fig. 11).
C-SYN
CDVI
Fig. 11
The...