Sim2 Multimedia Grand Cinema C3x Lumis 3d S Projector User Manual

Connections
❶ ❷ ❸ ❹ ❺ ❻
❼ ❽
Inputs ❶
HDMI 1
HDMI 2 Accept both HDMI and DVI  digital video inputs.
❷
Components/RGB-HV Four RCA connectors. They accept both standard  
and high-definition component (YPrPb) and  
RGB - HV signals. Also used as RGB input for SCART  
RGBS signals.
❸
Video One RCA connector. Accepts composite video sig -
nals. Also used as composite sync input for SCART  
RGBS signals.
❹
Graphics RGB One  D-Sub 15 - pin female  connector. Accepts  
component or RGB high-definition signals....

3D IR Emitter
The 3D infrared emitter is designed to be placed near the projector and aimed at the  
screen. It receives the 3D sync signal from the projector and emits infrared pulses that  
bounce off the screen and the walls to reach the 3D glasses infrared receiver.
Note:   The emitter emits sync pulses only when the projector displays 3D content.
3D Glasses
When displaying 3D content, the projector alternately displays one image for the left  
eye and one image for the right eye in rapid succession....

3 Installation
This section provides instructions for the installation of the Lumis 3D - S projector.
Important:  Installation procedures should be performed by a qualified AV system spe -
cialist.
Location
When installing the Lumis 3D - S projector, take the following considerations into ac -
count.
Installation Type
Select the installation type that best suits your needs:
• front or rear projection
• floor or ceiling mount
Lens Type
Choose the desired distance from the screen and select the lens type...

Ceiling Mounting
Invert the projector and suspend it from the ceiling using a specific bracket.
• To fit the bracket unscrew and remove the 3 rubber feet
• Attach bracket by using 3 x M6 screws not exceeding 15 mm in length
For ceiling mounting use only SIM2-approved ceiling brackets and adhere  
to the installation instructions and safety guidelines provided with the  
bracket. Do not over-tighten the screws.
Orientation
By default, the Lumis 3D - S is configured for a Front installation (projector...

If it is not possible to position the projector perpendicular to  
the projection screen (so that the lens center and screen cen -
ter are aligned with each other) you can use the mechanical  
lens control at the top of the projector to shift the projected  
image vertically:
• insert the provided hex wrench into the vertical lens  
shift adjuster
• turn the wrench to shift the lens in the desired direc -
tion
The Lumis 3D - S provides up to 50% of vertical lens shift up. For example, with a 16:9  
150...

throughout the entire signal path
◦ highest available resolution, because video sources can deliver full resolu -
tion content via HDMI only
◦ availability of 3D content, because most 3D compatible sources deliver 3D  
content from HDMI only
◦ optimization of several image parameters (2D/3D content, color space, as -
pect, signal range, over scan), thanks to auxiliary information (AVI in -
foframe) sent by the source device together with the signal.
If your source has dual HDMI outputs, we would...

Note:  RS-232 communications are limited to 15 m (50 ft.), whereas USB are limited to  
5   m (16 ft.).
Triggers
Some Home Theater devices can be controlled through a 12 V signal. The projector  
can output three 12 V (100 mA max) signals:
• TRIG1 for motorized screens control
• TRIG2 and TRIG3 are for motorized screen masks and anamorphic lens motors  
control. See “ Screen ”  and “ Anamorphic Lens ”  on page  27  for instructions on  
how to do configure them from OSD
Note:  Three jack adapters are...

Switching On and Off
Switching On
1. Turn on the main power switch on the right hand side of the projector. The  
projector enters the low power Standby status. The indicator light on the left  
hand side of the projector turns red and the status display next to it shows  . .
2. Press any of the numeric keys ( 0 - 9 ) on the remote control or the  I/O  button  
on the projector keypad to switch on the projector.
3. The indicator light turns green and red and the status display shows  88  for a  
while....

4 Operation
Viewing 3D Content
3D stereo visualization offers clear and sharp 3D images thanks to 3 chip DLP Imaging  
technology. This technique achieves channel separation using Xpand active shutter  
glasses.
• Active shutter glasses turn on and off in rapid succession and stop light reach -
ing your eyes. The glasses are synced using a IR emitter connected to the pro -
jector.
• When an image is destined for the left eye, the right lens of the glasses goes  
dark preventing any of the image for your...

select the correct one.
• Switch on your 3D glasses. Refer to the instructions supplied with the glasses  
to ensure correct operation.
• The projector will automatically detect the 3D signal and you will be prompted  
to wear your glasses via the OSD.
To Watch 3D Content via Satellite, Cable and Games Console
• Switch on the Lumis 3D - S and all other relevant products such as Satellite  
receiver and AV receiver and ensure the correct inputs have been selected.
• Select the appropriate 3D channel.
• If...