Sim2 Multimedia Domino 30 Projector User Manual

1
C
-S
YNC
1   INTRODUCTION
Congratulations and thank you for choosing a   projector,
a SIM2 Multimedia SpA product 
(Fig. 1). 

2
A sophisticated proprietary optical system, coupled with a hight
performance zoom lens ensures hight contrast images, superior
uniformity and edge-to-edge definition.
A new 6-segment colour wheel dramatically reduces the so
called “rainbow effect” and gives a better contrast, better
colorimetry and a lower black level to the image.
The  DMD™ chip resolution identifies the 
 projector:
1024x576 pixel for 
 model and 1280x720 pixel for
 model. For both models the high contrast ratio
deliver on the screen...

3
64
12358
7
C-S
YN
C
12111317
9
10
16
19
15
14
1820
1 Projection lens
2 Lens shift knob
3 Cooling air inlet vents
4 Remote control IR sensor
5 Cooling air outlet vents
6 Adjustable carry-handle
7 Adjustable levelling feet
8 Ceiling/wall bracket fixing holes
9 Fused power socket
10 Main power switch
11 Remote control rear IR sensor
12 Green LED
13 Red LED
14 Rear keyboard pad
15 Composite video input
16 S-Video input
17 VGA input
18 RGB / YCrCb input
19 12Vdc screen output
20 RS232 interface connector 

4
!
CAUTION
RISK OF ELECTRIC SHOCK!
DO NOT REMOVE THE TOP COVER
Prior to switching on the projector please read each chapter of this manual carefully as this manual provides basic
instructions for using the projector. If not specified the instructions in this manual are valid for 
 and 
projector. The installation of the lamp assembly, preliminary adjustments and procedures that necessitate the removal
of the top cover, must be carried out by authorised, trained technicians. There are no user serviceable...

5
Please follow carefully the warnings listed below, to ensure safe
and long term performance of your projector.
• Connect the projector to a power supply with a nominal
voltage within the following values: 100-240 Vac, 50/60 Hz,
earthed 
(Fig. 3).
100-240 Vac50/60 Hz
Fig. 3
• The mains plug is the disconnect device. Take care, when
installing, that the mains plug and socket outlet are easily
accessible. Never pull on the cable to take it out of the socket.
If the system is unlikely to be used for a...

6
• Take care not to shake the projector whilst carrying it by the
handle.
• Always position the projector  away from direct heat sources.
• Do not touch the surface of the projection lens.
• The projector must be positioned on a stable, suitable
platform or be installed using a bracket for fixed ceiling or
wall installation. Do not rest the projector on the side panels
or on the rear panel when in operation.
• Take care to position cables safely, especially in dark places,
in order to avoid a trip...

7
4   INSTALLATION
focus you should be able to clearly see each single pixel when
within close proximity to the screen 
(Fig. 7).
C
-
SY
NC
Fig. 7
The manual lens shift adjustment allows the projected image
to be moved vertically, up or down, in relation to the centre of
the screen; the maximum adjustment being equal to half the
height of the image in either direction 
(Fig. 8).
C-S
YNC
Fig. 8
In the event you are unable to centre the image within the screen
area, tilt the projector until the image is...

8
C-SYNC
Fig. 9
The Orientation adjustment in the Set up menu will allow the
projector to be used for desktop front, ceiling front, desktop
rear and ceiling rear installations 
(Fig. 10).
C-SYNC
Fig. 10
To activate an electric motorised screen a 12 Volt output is
provided at the rear of the projector or with the optional Remo-
te Input Interface.  This can be connected to a screen interface
unit, which can be supplied by screen manufacturers 
(Fig. 11).
C
-SYNC
Fig. 11
The output is activated (Voltage:...

9
5   SWITCHING ON AND OFF THE PROJECTOR
CAUTION: Connect the projector to a power supply
with a nominal voltage within the following values:
100-240 Vac, 50/60 Hz. It must be earthed 
(Fig. 12).
Posizione I : acceso
Posizione O : spento
Interruttore rete
Presa della rete
di alimentazione
Spina della rete
di alimentazione
Fig. 12
Upon switch on (in position I) the projector will initialise (red
and green LEDs on).  Followed by stand-by mode (red LED on)
(Fig. 13).
C-SYNC
Fig. 13
SWITCH ON FROM STAND-BY...

10
POWER OFF
INITIALIZATION
S TAT ENOTES INDICATORS
GREEN RED
STANDBY
OPERATING
COOLING LAMP
WARNING
ERRORThe Power is turned off
Power button has been pressed and the software is initialized (15 s)
Projector is in standby mode
Projector is on
Projector is powering down; the fans are running to cool the lamp (1 min)
Problems to display one or more source 
Internal circuit failure OFF
ON
OFF
ON
OFFOFF
ON
ON
OFF
FLASHING FLASHING
FLASHINGOFF
FLASHING
6   CONNECTIONS
To obtain the best performance from your...