Siemens Sn 65e001 Instructions For Use

							en11
Knife
 shelf *
* depending  on model
Long knives and other utensils can be arranged horizontally .
Y ou can remove the knife shelf to wash
taller utensils. Re-insert the knife shelf in the correct position.
Adjusting  the height of the
basket *
* depending  on model
If required, the height of the upper utensils basket can be adjusted to provide more space for tall utensils either in the upper or lower basket. Appliance height 81.5 cm
Top
basketBottom basket
Setting 1 max.  j22 cm30 cm
Setting 2 max. j24.5 cm27.5 cm
Setting 3 max. j27 cm25 cm
Appliance height 86.5 cm
Top
basketBottom basket
Setting 1 max.  j24 cm33 cm
Setting 2 max. j26.5 cm30.5 cm
Setting 3 max. j29 cm28 cm
Select one of the two following procedures according to the design of the top basket for your appliance model: 
Top basket with side levers
(Rackmatic)
Pull  out the top basket 20.
To  lower  the basket, press in the left
and then the right lever on the outside of the basket. In doing so, hold the sides of the basket along the upperedge to prevent it from suddenly dropping.
   
						

							en
12
To  raise  the basket, hold the basket on
the sides of the upper edge and lift it up.
Before re-inserting the basket again, ensure that it is at the same height onboth sides. Otherwise, the appliance door cannot be closed and the upper spray arm will not be connected to the water circuit.
Top  basket with upper
and lower roller pairs
Pull  out the top basket.
Remove the upper basket and re-attach it to the upper (stage 3) or lower(stage 1) rollers.
Detergent
Y ou can use tablets as well as powder
or liquid detergents for dishwashers, but never use washing up liquid. T ablets
contain not only detergent but alsorinse-aid and salt (3in1) and, depending on the combination (4in1, 5in1, etc.), additional components such as glassprotection or stainless steel cleaner .
If tablets contain rinse-aid and salt, it isusually not necessary to add additional rinse-aid and salt up to a specific degree of hardness. If the degree of hardness is higher and if using solo detergents (powder or liquid detergents or tabletswithout rinse-aid and salt) rinse-aid and salt must be added. The appliance doses these automatically according to the preset values for water hardness and amount of rinse-aid. As soon as combined detergent products are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result. 
TipFollow the instructions for use or the instructions on the detergent packaging to ensure that rinse-aid and salt are used 
effectively. If you have further questions, we recom- mend that you contact the detergent manufacturers helpline. Detergent  dispenser
with dosing aid The  graduated detergent dispenser 
30
helps you add the correct amount of powder or liquid detergent: lower line: 15 ml
middle line: 25 ml
full: 50 ml
  
						

							en13
Adding
 detergent
Pour detergent into the dispenser 30
(insert tablet flat, not on its edge).  Dosage: see manufacturer s
instructions on the packaging.
Close the cover on the detergent dispenser by sliding it up until the lock engages without dif ficulty.
The detergent dispenser opens automatically at the optimum time depending on the programme. The powder or liquid detergentis distributed in the appliance and is dissolved, the tablet falls into the tablet collecting tray where it dissolves in doses.
Tip If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate.
Warnings
Do  not  place small parts for washing
in the tablet collecting tray 
22 ; this
prevents the tablet from dissolving 
evenly.
If you want to add more utensils after the programme has started, do  not
use the tablet collecting tray 
22
as a handle for the upper basket. The tablet could already be there and you will touch the partially dissolved tablet. Note
Y
ou will obtain optimum rinsing and
drying results by using solo detergents and applying salt and rinse-aid 
separately.  
f programmes are short, tablets may not have full cleaning ef fect due to different
dissolving properties and there may even be undissolved detergent residue. It is recommended to use washing powder for these programmes.
The Intensive programme (on some models) requires one tab only . When
using washing powder , you can apply
some of this cleaning agent to theinside of the appliance s door.
Even if the rinse-aid and/or salt refill indicator is lit, the rinse programme willrun correctly if combined detergents are used (when using combined detergents, add rinse-aid at a waterhardness above 21  dH ± see chapter
entitled ªRinse-aidº).
If you switch from combined detergents to solo detergents, ensure that the water softening system and amountof rinse-aid have been set to the correct value.
If using detergents in a water-soluble protective cover: T ake hold of the cover
with dry hands only and put the detergent into an absolutely dry detergent dispenser only , otherwise
the detergent may stick.
  
						

							en
14 Overview
 of programmes
The  max. possible number of programmes is illustrated in this overview . The corresponding
programmes for your appliance can be found on the fascia.
Programme
T ype of utensils
and soilingProgramme sequencePossible additional options
Intensive 70 Pots, utensils and cutlery Highly soiledPrerinse Clean 70
Intermediate rinse Final rinse 70 
Dryall
Normal 65 Utensils and cutlery Normally soiledPrerinse Clean 65
Intermediate rinse Final rinse 65 
Dryall
Auto 45 ±65 Utensils and cutlery Normally soiledIs optimised according to the soiling with the aid of sensors.all
Eco 50 Utensils and cutlery Normally soiledPrerinse Clean 50 
Intermediate rinse Final rinse 65 
Dryall
Gentle 40 Utensils and cutlery Lightly soiledPrerinse Clean 40
Intermediate rinse Final rinse 55 
Dry Express W ash
Half load Extra drying
Quick 45 Utensils and cutlery Lightly soiledClean 45 
Intermediate rinse Final rinse 55 Extra drying
PrerinseLightly soiledPrerinsenone
Programme  selection
You  can select a suitable programme
according to the type of utensils and degree of soiling. Information  about comparability
tests The  conditions for running comparability
tests can be found on the supplementary sheet ªInformation for comparability testsº.
              
						

							en15
Additional
 options
* depending  on model
Additional options 
3 can be set with the
buttons.
Express  Wash
(VarioSpeed) *
The  >>Express W ash 6.
Press the Start button 9.
Close the door .
The programme starts running.
      
						

							en
16
Timer
 programming *
* depending  on model
Y ou can delay the start of the programme
by 3, 6 or 9 hours.
Switch on ON/OFF switch 1.
Keep pressing the Preselected starting time button 
2 until the appropriate
display 3 h, 6 h or 9 h is lit.
Press Start button 9.
The preselected starting time is activated.
T o delete the preselected starting time,
keep pressing the Preselected starting time button 
2 until none of the
displays 3 h, 6 h or 9 h is lit. Y ou can change your programme
selection at any time until the programme starts.
End  of programme
The  programme has ended when the End
display 
8 is lit.
The end of the programme is also indicated by an acoustic signal. The buzzer volume can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit. (see water hardness table). Factory setting: 2. This function can be changed as follows:
Open the door .
Switch on ON/OFF switch 1.
Hold down button > 6 and press
Start button 
9 until the End display
8  and salt refill indicator 11 flash.
Release buttons.
Keep pressing button > 6 until the
salt refill indicator 
11  and  rinse aid
refill indicator 
10 flash.
Release buttons. The refill indicator 
11  flashes and
the displays 
10 and A  are B lit
(= setting 2). The set buzzer volume can be heard. Change the setting as follows:
ress button < 5 until the required
setting has been selected.
Press Start button 9.
The displays go out. The selected setting is saved.
Close the door .
Switching  off the appliance
Short  time after the end of the programme:
Open the door .
Switch off ON/OFF switch 1.
Turn of f the tap (not applicable
if  Aqua-Stop fitted).
Remove the utensils when they have cooled down.
Warning
At the end of the programme please open the door fully and not partially when emptying the dishwasher . Any escaping
water vapour could damage sensitive worktops. Interrupting  the programme
Open the door .
Switch of f ON/OFF switch 1. 
The LEDs go out. The programme is saved.  If the door was opened on an appliance which has a warm water connectionor is heated, first leave the door ajarfor several minutes and then close.Otherwise, expansion (pressure) maycause the appliance door to springopen or water to run out of theappliance.
T o continue the programme, switch
on the ON/OFF switch 
1 again.
Close the door .
 
						

							en17
Terminating
 the programme
(Reset)
Open  the door .
Press Start button 9 for
approx. 3 sec. The Cleaning display 
7  goes out.
Close the door . 
The remaining programme sequence lasts approx. 1 more minute.(Buzzer sounds).
Open the door .
Switch off ON/OFF switch 1.
Close the door .
Changing  the programme
When  the ST ART button 
9 has been
pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (reset). Intensive  drying
The  final rinse uses a higher temperature
which improves the drying result. The running time may increase slightly .
(Caution if utensils are delicate!)
Open the door .
Switch on ON/OFF switch 1.
Hold down button > 6 and press
Start button 
9 until the End display
8  and salt refill indicator 11 flash.
Release buttons.
Keep pressing button > 6 until the
salt refill indicator 
11  and  ªCheck
water supplyº 
12 flash.
Release buttons. The displays 
11  and 12 flash.
Change the setting as follows:
Press button < 5 until the display
A  is lit (Intensive drying on).
Press Start button 9.
The displays go out. The setting is saved.
Close the door . Maintenance
 and care
A  regular inspection and maintenance of
your machine will help to prevent faults. This saves time and prevents problems. Overall  condition
of the machine
Check  spray arm for grease and
limescale deposits.
If you find such deposits:
Fill detergent dispenser with detergent. Start the appliance without utensils inthe programme with the highest rinsingtemperature.
Clean the appliance with detergents/appliance cleaners which are particularlysuitable for use with dishwashers.
Regularly clean door seal with a damp cloth.
Never use a steam cleaner to clean your dishwasher . The manufacturer is not liable
for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate.Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: T o prevent
corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
Warning
Never use other chlorinated household detergents! Health hazard! Salt  and rinse-aid
Check  the refill indicators 11 and 10.
If required, refill salt and/or rinse-aid.
 
						

							en
18
Filters The filters 
26
 keep large foreign objects
in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter ,
a flat fine filter and a microfilter .
After each washing cycle check the filters for residue.
Unscrew filter cylinder as illustrated and take out filter system.
Remove any residue and clean filters under running water.
Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. Spray
 arms
Limescale  and contaminants in the rinsing
water may block nozzles and bearings on the spray arms 
23  and 24 .
Check outlet nozzles on the spray arms for blockages.
Unscrew the upper spray arm 23.
Remove the lower spray arm 24
upwards.
Clean spray arms under running water .
Re-engage or screw on spray arms.
    
						

							en19
Waste
 water pump
Large  food remnants in the rinsing water
not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter .
In this case:
First disconnect the appliance from the power supply .
Remove the filters 26.
Scoop out water , use a sponge
if required.
Using a spoon, prise of f pump cover
(as illustrated) until it clicks, then grip the cover by the lug and first pull it upwards until it resists and then pull it out forwards.
Check inner compartment and remove any foreign objects.
Place cover in the original position, press down and engage.
Install filters. Troubleshooting
Experience has shown that you can rectify most faults which occur in daily operationwithout calling customer service. Obviously this will save on costs and ensure that the machine is quickly available again. The following overview should help you locate the causes of faultswhich may occur .
Warning
Remember: Repairs may be carried out by technicians only . If a component has to be
replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. ...  when the appliance is
switched on
The  appliance does not start.
The mains fuse has tripped.
The appliance plug has not been inserted.
The appliance door has not been shut properly .
...  on the appliance
Lower  spray arm rotates sluggishly .
Spray arm blocked.
The door is difficult to open. *
Child-proof lock is activated. The deactivation instructions are at the back in the envelope. * depending on model
Door cannot be closed.
Door lock has been activated. To reset, close the door with
greater force.
   
						

							en
20
Cover on the detergent dispenser cannot be closed.
Detergent dispenser overfilled or mechanism blocked by sticky detergent residue.
Detergent residue in the detergent 
dispenser.
Dispenser was damp when filled.
ªcheck water supplyº 12 display
lights up.
T ap turned of f.
Water supply interrupted.
Supply hose kinked.
Filter in the water supply blocked.
Switch of f the appliance and
pull out the mains plug.
T urn of f the tap.
Clean filter in the supply hose.
Reconnect power supply .
Turn on the tap.
Switch on the appliance.
W ater is left in the appliance
at the end of the programme.
W aste water hose is blocked
or kinked.
W aste water pump blocked,
cover on the waste water pump is not locked in position (see Maintenance and Care).
Filters blocked.
The programme has not yet ended. W ait until programme
ends or implement ºResetº function.
The ªCheck water supplyº display
12 flashes rapidly .
Water in the safety system.
Switch of f the appliance and
pull out the mains plug.
T urn of f the tap.
Contact customer service.
Refill indicator for salt 11 and/or
rinse-aid 
10 is not lit.
Refill indicator/s switched of f.
Adequate salt/rinse-aid available.
Refill indicator for special salt 11
is lit.
No salt.  Refill with salt.
Sensor does not detect salt tablets.  Use different special salt.
...  during the wash cycle
Unusual  foam formation
Handwash liquid in the rinse aid dispenser .
Spilled rinse-aid causes excessive frothing, therefore please remove with a cloth.
Appliance stops during the wash cycle.
Power supply interrupted.
W ater supply interrupted.
Knocking/rattling noise during rinsing
Spray arm is striking utensils.
Utensils not arranged correctly .
Filling valves making striking noises
Caused by the installation of the water line and has no effect on the
function of the machine. Remedialaction is not possible.