Siemens Sn 64m080 Operating Instructions

Fault, what to do?en
31
Water stains on plastic  
parts
Droplet formation on plastic 
surface is physically unavoidable.  
After drying, water stains are  
visible. Use a more intensive programme (more  
water changes). 
Arrange utensils in a sloping position.  
Use rinse aid.
If required, increase softening setting.
Washable or water-soluble  
coatings in the container or  
on the door. Detergent substances are  
deposited. These coatings cannot  
usually be removed with 
chemicals (appliance cleaner,...

enFault, what to do?
32
Coloured (blue, yellow,  
brown), difficult to remove  
to non-removable coatings  
in the appliance or on 
stainless steel utensils.
Film formation consisting  
of ingredients from vegetables  
(e.g. cabbage, celery, potatoes,  
noodles, ...) or the tap water (e.g.  
manganese). Can be partly removed with machine  
cleaner or by mechanical cleaning. Coatings  
are harmless.
Film formation caused by metallic  
components on silver or  
aluminium utensils. Can be partly removed...

Fault, what to do?en
33
Rust spots on the cutlery. Cutlery not adequately rust-
resistant. Knife blades are  
frequently more severely  
affected. Use corrosion-resistant cutlery.
Cutlery will also rust if rusting 
parts are rinsed at the same time 
(pan handles, damaged utensil  
baskets, etc.). Do not wash rusting parts.
Salt content in the rinsing water 
too high, as salt dispenser lock  
not fastened firmly or salt was 
spilled while being refilled. Fasten salt dispenser lock firmly or remove...

enFault, what to do?
34
 
Appliance stops  
in the programme or  
programme is interrupted.
Door not closed properly. Close the door. 
Do not place utensils or fragrance  
dispenser in the tablet collecting 
tray. 
Top basket presses against inner  
door and prevents door from  
being closed securely. Check whether rear panel is being pressed  
in, e.g. by socket or by hose holder which 
has not been removed.
Power and/or water supply  
interrupted. Restore power and/or water supply.
Filling valves...

Customer serviceen
35
4 Customer serviceCustomer service
If you are unable to rectify the fault,  
please contact your customer service.  
We always find a suitable solution, even  
to avoid unnecessary visits  
by technicians. Contact information  
for your nearest customer service can  
be found on the back of these  
instructions for use or on the enclosed  
customer service list. When calling,  
please state the appliance number (E- 
Nr. = 1) and the production number  
(FD = 2) which can be found on...

enInstallation and connection
36
Delivery 
Your dishwasher has been checked  
thoroughly in the factory to ensure that it  
is in working order. This may cause  
small water stains. These will disappear 
after the first wash cycle. 
Technical specifications 
Weig ht: 
max. 60 kg 
Voltage:
220–240 V, 50 Hz or 60 Hz 
Connected load: 
2.0–2.4 kW 
Fuse:
10/16 A (UK 13A) 
Power input: 
switched off 0.1 W 
not switched off 0.1 W 
Water pressure: 
at least 0.05 MPa (0.5 bar), maximum  
1 MPa (10 bar). At a...

Installation and connectionen
37
Fresh water connection 
1.
Connect the fresh-water connection  
to the tap according to the  
installation instructions with the  
enclosed parts. 
Ensure that the fresh-water  
connection is not kinked, crushed or  
twisted.
2. When replacing the appliance,  
always use a new water supply hose.
Water pressure: 
at least 0.05 MPa (0.5 bar), maximum  
1 MPa (10 bar). At a higher water  
pressure: connect pressure-reducing  
valve ahead. 
Inlet rate: 
minimum 10...

enInstallation and connection
38


      



   



DownloadedfromDishWasherManualcomManuals  

 
 

 
 


 

 
 
 
 
 



 
 
 






 
 
 


 

 


*9000836800* 
9000836800
 en (9211) 640MV