Siemens Sn 56m532 Instructions For Use

aus11
Adding
 detergent
Pour detergent into the dispenser 29
(insert tablet flat, not on its edge).  Dosage: see manufacturer s
instructions on the packaging.
Close the cover on the detergent dispenser by sliding it up until the lock engages without dif ficulty.
The detergent dispenser opens automatically at the optimum time depending on the programme. The powder or liquid detergentis distributed in the appliance and is dissolved, the tablet falls into the tablet collecting tray where it dissolves in...

aus
12 Overview
 of programmes
The  max. possible number of programmes is illustrated in this overview . The corresponding
programmes for your appliance can be found on the fascia. The programme data are values measured in the laboratory in compliance with Standard AS/NSZ 2007.
Programme
T ype of
utensils and soilingProgramme sequencePossible additionaloptions   
    
      
  
      
  
    
Pots and Pans 70Pots, utensils and cutleryHighly soiledPrerinse Clean 70 
Intermediate rinse Final rinse 70...

aus13
Programme
 selection
You  can select a suitable programme
according to the type of utensils and degree of soiling. Information  about comparability
tests The  conditions for running comparability
tests can be found on the supplementary sheet ªInformation for comparability testsº. Additional
 options
* depending  on model
Additional options 
7 can be set with the
buttons.
Saving  time (V arioSpeed) *
The  >>Save time

aus
14 Washing
 the dishes
Aqua  sensor *
* depending  on model
The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water .
The Aqua sensor is used according to the programme. If the Aqua sensor is active, ªcleanº rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3±6 litres. If the turbidity is greater , the water is drained
and is replaced with fresh water . In the
automatic programmes the temperatureand...

aus15
Switching
 off the appliance
Short  time after the end of the programme:
Switch of f ON/OFF switch 1.
Turn of f the tap (not applicable
if  Aqua-Stop fitted).
Remove the utensils when they have cooled down.
Warning
At the end of the programme please open the door fully and not partially whenemptying the dishwasher . Any escaping
water vapour could damage sensitiveworktops. Interrupting  the programme
Switch off ON/OFF switch 1.
The LEDs go out. The programme is saved.  If the door was opened on an...

aus
16 Maintenance
 and care
A  regular inspection and maintenance of
your machine will help to prevent faults. This saves time and prevents problems. Overall  condition
of the machine
Check  spray arm for grease and
limescale deposits.
If you find such deposits:
Fill detergent dispenser with detergent. Start the appliance without utensils inthe programme with the highest rinsingtemperature.
Clean the appliance with detergents/appliance cleaners which are particularlysuitable for use with dishwashers....

aus17
Spray
 arms
Limescale  and contaminants in the rinsing
water may block nozzles and bearings on the spray arms 
23  and 24.
Check outlet nozzles on the spray arms for blockages.
Unscrew the upper spray arm 23 .
Remove the lower spray arm 24
upwards.
Clean spray arms under running water .
Re-engage or screw on spray arms. Waste
 water pump
Large  food remnants in the rinsing water
not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the...

aus
18 Troubleshooting
Experience has shown that you can rectify most faults which occur in daily operationwithout calling customer service. Obviously this will save on costs and ensure that the machine is quickly available again. The following overview should help you locate the causes of faultswhich may occur .
Warning
If an error code  (E:01 to E:30) is indicated
on the digital display 
10, always
disconnect the appliance from the power supply and then turn of f the tap.
Y ou can rectify certain...

aus19
Reconnect power supply .
Turn on the tap.
Switch on the appliance.
W ater is left in the appliance
at the end of the programme.
(E24)  Waste water hose is
blocked or kinked.
(E25)  Waste water pump
blocked, cover on the waste water pump is not locked in position (see Maintenanceand Care).
Filters blocked.
The programme has not yet ended. W ait until programme
ends (digital display indicates 0:00) or implement the ºResetº function.
Refill indicator for rinse-aid 4 is
not lit.
Refill indicator...

aus
20 Customer
 service
If  you are unable to rectify the fault, please
contact your customer service. Y our nearest customer service centre can
be found in the customer service list.When calling customer service, please quote the appliance number (1) and the FD number (2) which can be found on the rating plate 
31 on the appliance door .
FD
1 2
Warning
Please note that a visit by a customer service technician to repair a malfunctionor one of the described faults will not be free of charge  even during...