Siemens Sn 56m532 Instructions For Use

							aus11
Adding
 detergent
Pour detergent into the dispenser 29
(insert tablet flat, not on its edge).  Dosage: see manufacturer s
instructions on the packaging.
Close the cover on the detergent dispenser by sliding it up until the lock engages without dif ficulty.
The detergent dispenser opens automatically at the optimum time depending on the programme. The powder or liquid detergentis distributed in the appliance and is dissolved, the tablet falls into the tablet collecting tray where it dissolves in doses.
Tip If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate.
Warnings
Do  not place small parts for washing
in the tablet collecting tray 
22 ; this
prevents the tablet from dissolving 
evenly.
If you want to add more utensils after the programme has started, do  not
use the tablet collecting tray 
22
as a handle for the upper basket. The tablet could already be there and you will touch the partially dissolvedtablet.
Note
f programmes are short, tablets may not have full cleaning ef fect due to different
dissolving properties and there mayeven be undissolved detergent residue. It is recommended to use washing powder for these programmes.
The Intensive programme (on some models) requires one tab only . When
using washing powder , you can apply
some of this cleaning agent to theinside of the appliance s door.
If using detergents in a water-soluble protective cover: T ake hold of the cover
with dry hands only and put the detergent into an absolutely dry detergent dispenser only , otherwise
the detergent may stick.
  
						

							aus
12 Overview
 of programmes
The  max. possible number of programmes is illustrated in this overview . The corresponding
programmes for your appliance can be found on the fascia. The programme data are values measured in the laboratory in compliance with Standard AS/NSZ 2007.
Programme
T ype of
utensils and soilingProgramme sequencePossible additionaloptions   
    
      
  
      
  
    
Pots and Pans 70Pots, utensils and cutleryHighly soiledPrerinse Clean 70 
Intermediate rinse Final rinse 70 
Dryall1.) 2:15 2.) 1,50 3.) 154.) 12
Intensive 65 Pots, utensils and cutleryHighly soiledPrerinse Clean 65
Intermediate rinse Final rinse 70 
Dryall1.) 2:00 2.) 1,45 3.)  144.) ±
Auto 45  ± 65 Utensils and cutlery NormallysoiledIs optimised according to the soiling with the aidof sensors.all1.) 1:25-2:30 2.) 1,00-1,60 3.)  ±4.) 9-19
Normal 45 Utensils and cutlery NormallysoiledPrerinse Clean 45
Intermediate rinse Final rinse 45 
Dryall1.) 2:20 2.) 0,62 3.) 12,34.)  ±
Quick 45 Utensils and cutlery Lightly soiledClean 45 
Intermediate rinse Final rinse 55 Extra drying1.) 0:29 2.) 0,80 3.) 104.)  ±
PrerinseLightly soiledPrerinsenone1.) 0:15 2.) 0,05 3.) 44.)  ±
           
						

							aus13
Programme
 selection
You  can select a suitable programme
according to the type of utensils and degree of soiling. Information  about comparability
tests The  conditions for running comparability
tests can be found on the supplementary sheet ªInformation for comparability testsº. Additional
 options
* depending  on model
Additional options 
7 can be set with the
buttons.
Saving  time (V arioSpeed) *
The  >>Save time
						

							aus
14 Washing
 the dishes
Aqua  sensor *
* depending  on model
The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water .
The Aqua sensor is used according to the programme. If the Aqua sensor is active, ªcleanº rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3±6 litres. If the turbidity is greater , the water is drained
and is replaced with fresh water . In the
automatic programmes the temperatureand running time can also be adjusted to the degree of soiling. Switching  on the appliance
Turn on the tap fully .
Close the door.
Switch on ON/OFF switch 1.
The display of the last selected programme flashes. This programme remains selected if no other programme button 
2 is pressed.
The expected programme duration flashes on the digital display 
10.
Press the ST ART button 8.
The programme starts running.
Programme  sequence
indicator 
9
Your  dishes are being
cleaned.
Y our dishes are being rinsed.
Y our dishes are being dried.
Remaining  running time display
When  the programme is selected, the
remaining running time of the programme is indicated on the digital display 
10.
The running time is determined during the programme by the water temperature, thenumber of utensils as well as the degree of soiling and may vary (depending on the selected programme). 
Timer  programming *
* depending  on model
Y ou can delay the start of the programme
in 1-hour steps up to 24 hours.
Close the door .
Switch on ON/OFF switch 1.
Press 6 + button until the digital
display 
10 jumps to .
Press 6 + or ± button until the
displayed time corresponds with your requirements.
Press ST ART button 8, timer
programming is activated.
T o delete timer programming, press
the 
6 + or ± button until 
is indicated on the digital display .
Y ou can change your programme
selection at any time until the programme starts.
End  of programme
The  programme has ended when the
value 
 is indicated on the numerical
display 
10.
          
						

							aus15
Switching
 off the appliance
Short  time after the end of the programme:
Switch of f ON/OFF switch 1.
Turn of f the tap (not applicable
if  Aqua-Stop fitted).
Remove the utensils when they have cooled down.
Warning
At the end of the programme please open the door fully and not partially whenemptying the dishwasher . Any escaping
water vapour could damage sensitiveworktops. Interrupting  the programme
Switch off ON/OFF switch 1.
The LEDs go out. The programme is saved.  If the door was opened on an appliance which has a warm water connection oris heated, first leave the door ajar forseveral minutes and then close.Otherwise, expansion (pressure) maycause the appliance door to springopen or water to run out of theappliance.
T o continue the programme, switch on
the ON/OFF switch 
1 again.
Terminating  the programme
(Reset)
Press  START button 8 for approx.
3 sec. The numerical display 
10 indicates
.
The programme sequence lasts approx. 1 min.On the digital display 
10 is indicated
.
Switch of f ON/OFF switch 1. Changing
 the programme
When  the ST ART button 
8 has been
pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (reset). Intensive  drying
The  final rinse uses a higher temperature
which improves the drying result. The running time may increase slightly .
(Caution if utensils are delicate!)
Close the door .
Switch on ON/OFF switch 1.
Hold down programme button A and
press ST ART button 8 until on the
digital display 
10 is indicated .
Release both buttons.
T o change the setting,
Press the button C  to switch
intensive drying on 
 or of f .
Press ST ART button 8.
The set value is saved.
      
						

							aus
16 Maintenance
 and care
A  regular inspection and maintenance of
your machine will help to prevent faults. This saves time and prevents problems. Overall  condition
of the machine
Check  spray arm for grease and
limescale deposits.
If you find such deposits:
Fill detergent dispenser with detergent. Start the appliance without utensils inthe programme with the highest rinsingtemperature.
Clean the appliance with detergents/appliance cleaners which are particularlysuitable for use with dishwashers.
Regularly clean door seal with a damp cloth.
Never use a steam cleaner to clean your dishwasher . The manufacturer is not liable
for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate.Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: T o prevent
corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
Warning
Never use other chlorinated household detergents! Health hazard! Rinse-aid
As soon as the rinse-aid refill indicator lights up on the control panel 
4,
refill with rinse aid. Filters The filters 
25
 keep large foreign objects
in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter ,
a flat fine filter and a microfilter .
After each washing cycle check the filters for residue.
Unscrew filter cylinder as illustrated and take out filter system.
Remove any residue and clean filters under running water.
Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system.
   
						

							aus17
Spray
 arms
Limescale  and contaminants in the rinsing
water may block nozzles and bearings on the spray arms 
23  and 24.
Check outlet nozzles on the spray arms for blockages.
Unscrew the upper spray arm 23 .
Remove the lower spray arm 24
upwards.
Clean spray arms under running water .
Re-engage or screw on spray arms. Waste
 water pump
Large  food remnants in the rinsing water
not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter .
In this case:
First disconnect the appliance from the power supply .
Remove the filters 25.
Scoop out water , use a sponge
if required.
Using a spoon, prise of f pump cover
(as illustrated) until it clicks, then grip the cover by the lug and first pull it upwards until it resists and then pull it out forwards.
Check inner compartment and remove any foreign objects.
Place cover in the original position, press down and engage.
Install filters.
    
						

							aus
18 Troubleshooting
Experience has shown that you can rectify most faults which occur in daily operationwithout calling customer service. Obviously this will save on costs and ensure that the machine is quickly available again. The following overview should help you locate the causes of faultswhich may occur .
Warning
If an error code  (E:01 to E:30) is indicated
on the digital display 
10, always
disconnect the appliance from the power supply and then turn of f the tap.
Y ou can rectify certain faults yourself
(see following fault description), for all other faults please contact customer service and state the indicated fault  E:XX.
Warning
Remember: Repairs may be carried out by technicians only . If a component has to be
replaced, ensure that only original spareparts are used. Improper repairs or use of non-original spare parts may causeconsiderable damage and put the user at considerable risk. ...  when the appliance is
switched on
The  appliance does not start.
The mains fuse has tripped.
The appliance plug has not been inserted.
The appliance door has not been shut properly .
...  on the appliance
Lower  spray arm rotates sluggishly .
Spray arm blocked.
The door is difficult to open. *
Child-proof lock is activated. The deactivation instructions are at the back in the envelope. * depending on model
Door cannot be closed.
Door lock has been activated. To reset, close the door with
greater force.
...  changing settings
A setting cannot be changed,
a programme starts.
W rong programme button pressed.
T erminate the programme
(see chapter entitled ªT erminating
the programme (Reset)º) and start all over again.
Y ou did not wait until programme
ended.
Cover on the detergent dispenser cannot be closed.
Detergent dispenser overfilled or mechanism blocked by sticky detergent residue.
Detergent residue in the detergent 
dispenser.
Dispenser was damp when filled.
ªcheck water supplyº 3 display
lights up.
T ap turned of f.
Water supply interrupted.
Supply hose kinked.
Filter in the water supply blocked.
Switch of f the appliance and
pull out the mains plug.
T urn of f the tap.
Clean filter in the supply hose.
 
						

							aus19
Reconnect power supply .
Turn on the tap.
Switch on the appliance.
W ater is left in the appliance
at the end of the programme.
(E24)  Waste water hose is
blocked or kinked.
(E25)  Waste water pump
blocked, cover on the waste water pump is not locked in position (see Maintenanceand Care).
Filters blocked.
The programme has not yet ended. W ait until programme
ends (digital display indicates 0:00) or implement the ºResetº function.
Refill indicator for rinse-aid 4 is
not lit.
Refill indicator switched of f.
Adequate rinse-aid available.
...  during the wash cycle
Unusual  foam formation
Handwash liquid in the rinse aid dispenser .
Spilled rinse-aid causes excessivefrothing, therefore please remove with a cloth.
Appliance stops during the wash cycle.
Power supply interrupted.
W ater supply interrupted.
Knocking/rattling noise during rinsing
Spray arm is striking utensils.
Utensils not arranged correctly .
Filling valves making striking noises
Caused by the installation of the water line and has no effect on the
function of the machine. Remedialaction is not possible. ...
 on the utensils
Food  residue on the utensils.
Utensils placed too closely together , utensils basket overfilled.
Too little detergent.
Rinse programme too weak.
Spray arm rotation obstructed.
Spray arm nozzles blocked.
Filters blocked.
Filters incorrectly inserted.
W aste water pump blocked.
Top basket on right and left not set
to same height.
T ea or lipstick residue is not
completely removed.
Detergent has inadequate bleaching ef fect.
Too low rinsing temperature.
Too little/unsuitable detergent
Dull, discoloured glasses, film cannot be washed off.
Unsuitable detergent.
Glasses not dishwasher-proof.
Streaks on glasses and cutlery ,
glasses have metallic appearance.
T oo much rinse-aid.
Plastic parts discoloured.
Too little/unsuitable detergent.
Too weak programme selected.
Rust spots on the cutlery .
Cutlery not rust-resistant.
Utensils not dry.
Appliance door opened too early and utensils taken out too early .
Programme selected without drying.
Too little rinse-aid.
 
						

							aus
20 Customer
 service
If  you are unable to rectify the fault, please
contact your customer service. Y our nearest customer service centre can
be found in the customer service list.When calling customer service, please quote the appliance number (1) and the FD number (2) which can be found on the rating plate 
31 on the appliance door .
FD
1 2
Warning
Please note that a visit by a customer service technician to repair a malfunctionor one of the described faults will not be free of charge  even during the warranty
period. Installation
The dishwasher must be connected correctly , otherwise it will not function
properly . The specifications for the inlet
and outlet as well as the electricalconnected loads must correspond with the required criteria as specified in the following paragraphs or in the installationinstructions. Install the appliance in the correct sequence:
Checking appliance on delivery
Installing the appliance
W aste-water connection
Fresh-water connection
Electrical connection