Siemens Sn 25e810 Operating Instructions

Operating the applianceen
21
5.
Press START button  @, timer 
programming is activated.
6. To delete the preselected starting  
time, press the button  P until  œ is 
indicated on the digital display.   
You can change your programme  
selection at any time until the  
programme starts.
End of programme 
The programme has ended when the  
value  ‹:‹‹  is indicated on the numerical 
display  H.  
Switching off automatically  
after the end of 
the programme *
Sw it ch
in g
 o ff
 a u
to mat ic all y...

enCleaning and maintenance
22
T
er min
at in
g t he pr o
gr ammeTerminating the programme 
(Reset) 
1. Press START button @ for 
approx. 3 sec. 
The numerical display H 
indicates ‹:‹‚ .
2. The programme sequence lasts  
approx. 1 min. On the digital  
display H is indicated ‹:‹‹ .
3. Switch off ON/OFF switch (.
Changing the programme 
When the START button  @ has been 
pressed, the programme cannot be  
changed. 
The only way a programme can be  
changed is by Cancel programme  
(Reset). 
Intensive...

Cleaning and maintenanceen
23
ã
Warning – Health hazard
Never use other domestic detergents,  
e.g. containing chlorine!  
Special salt and rinse aid


enFault, what to do?
24
3 Fault, what to do?Fault, what to do?
Experience has shown that you can  
rectify most faults which occur in daily 
operation yourself. This ensures that  
the machine is quickly available to you  
again. In the following overview you can  
find possible causes of malfunctions  
and helpful information for rectifying  
them. 
Note 
If the appliance stops during  
dishwashing or does not start for no  
obvious reason, first run the Abort  
programme function (Reset). 
(See chapter...

Fault, what to do?en
25
Fault table 
Fault Cause Remedial action 
“Check water supply”  
display
) lights up. Supply hose kinked. Install supply hose without kink
s.
Tap turned off. Turn on the tap. 
Tap jammed or calcified. Turn on the tap. Flow rate must be min. 10 l/min.  
when water supply is open.
Filter in the water supply blocked. Switch off the applia nce and pull out 
the mains plug. Turn off the tap. Unscrew  
water connection.  
Clean filter in the supply hose. Screw water  
connection on...

enFault, what to do?
26
A different error code is  
indicated on the digital  
display. 
(
“ :‹‚  to“:„‹ ) A technical fault has probably  
occurred.
Switch off appliances with the ON/OFF 
switch
(. After a short time restart 
the appliance. 
If the problem recurs, turn off the tap and  
pull out the mains plug.  
Call customer service and mention the error  
code.
Display flashes Door not closed properly. Close the door . Ensure that no objects 
(utensil, fragrance dispenser) are protruding  
over the...

Fault, what to do?en
27
Utensils not dry. No or too little rinse aid 
in the dispenser. Refill rinse aid.
Programme selected without  
drying. Select programme with drying (see 
Overview of programmes, Programme  
sequence).
Water collecting in depressions 
on the utensils and cutlery. Arrange utensils in a sloping position, 
arrange affected utensils as sloping  
as possible.
The combined detergent used  
has a poor drying performance. Use different combination detergent with 
better drying performance....

enFault, what to do?
28
Food remnants  
on the utensils.
Utensils placed too closely 
together, utensils basket  
overfilled. Arrange utensils with adequate clearance  
between them ensuring that the spray jets  
can reach the surface of the utensils. 
Prevent contact points.
Spray arm rotation obstructed. Arrange utensils so t hat the spray arm can 
rotate without obstruction.
Spray arm nozzles blocked. Clean the spray arm nozzle s, 
(See Cleaning and maintenance).
Filters  1R dirty. Clean filters, (see...

Fault, what to do?en
29
Water stains on plastic  
parts
Droplet formation on plastic 
surface is physically unavoidable.  
After drying, water stains are 
visible. Use a more intensive programme (more  
water changes). 
Arrange utensils in a sloping position.  
Use rinse aid. 
If required, increase softening setting.
Washable or water-soluble  
coatings in the container or  
on the door. Detergent substances are  
deposited. These coatings cannot  
usually be removed with  
chemicals (appliance cleaner,...

enFault, what to do?
30
Coloured (blue, yellow,  
brown), difficult to remove  
to non-removable coatings 
in the appliance or on  
stainless steel utensils.
Film formation consisting 
of ingredients from vegetables  
(e.g. cabbage, celery, potatoes, 
noodles, ...) or the tap water (e.g.  
manganese). Can be partly removed with machine  
cleaner or by mechanical cleaning. Coatings  
are harmless.
Film formation caused by metallic  
components on silver or  
aluminium utensils. Can be partly removed with...