Siemens Sf 24e232 Instructions For Use

en21
Spray
 arms
Lime  and remnants of food in the washing
water can block the nozzles in the spray arms 
22  and 23 and the arm
mountings .
Inspect the nozzles in the spray arms for blocked holes due to remnants offood.
If necessary , pull the lower arm 23
upwards and lift it of f.
Unscrew the upper spray arm 22.
Clean both spray arms under running 
water.
Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. Pump
 *
*  on applicable models
Larger...

en
22 Fault
 finding
Resolving  minor problems
yourself Experience  has shown that you can
resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer . Not
only does this save costs, but it alsomeans that the appliance is available for use again that much sooner . The following
list of common occurrences and their remedies should help you identify the causes of most problems. Problems  ...
Attention
Remember:  Repairs may be
carried out by a...

en23
Remnants of detergent stuck inside dispenser
Compartment was damp when it was filled up with detergent. Compartment must be dry beforedetergent is added.
Water remains inside appliance
after programme has ended
Blockage or kink in drainage hose.
Pump is jammed.
Filters are blocked.
The programme is still running. W ait for the programme to end.
Perform ªResetº function.
...  during washing
Unusual  amount of foam is created
Normal washing up liquid has been poured into the rinse-aid 
container....

en
24
Glasses have a dull appearance
Amount of rinse-aid was set too 
low.
T ea stains or traces of lipstick have
not been completely removed
Detergent does not have a suf ficient bleaching ef fect.
Washing temperature was set too
low.
T races of rust on cutlery
Cutlery is not suf ficiently rustproof.
Salt content in washing water is too high.
Lid on salt container is not screwed tight.
Too much salt was spilt while
filling container .
Glasses become clouded and discoloured; coating cannot be wiped off...

en25
Information
Notes  on comparison tests
You  will find details of the conditions for
the comparison tests on the additional ºNotes on comparison testsº sheet. The consumption values for the relevant programmes are given in the introduction. General
Built-under and integrated appliances which are subsequently installed as free-standing appliances must be secured to prevent them from falling over , e.g. by screwing them to the wall
or by installing them under a continuous worktop which is screwed to...

en
26
Fresh
 water connection
Using  the enclosed parts, connect the
fresh water connection to the tap according to the installation instructions. Ensure that the fresh water connection isnot kinked, crushed or twisted. When replacing the appliance, always connect a new water supply hose to the water supply . The old supply hose must
not be re-used. W ater pressure:
Minimum 0,05 MPa (0,5 bar) ± maximum 1 MPa (10 bar). If the water pressure is higher , install a
pressure reducing valve. Flow rate:Minimum...

en27
Waste
 disposal
Disposal Old  appliances are not worthless rubbish.
V aluable raw materials can be reclaimed
by recycling old appliances. Pull out the mains plug of the redundant appliance. Cut of f the power cord and
discard with mains plug.T o prevent children from locking
themselves in the appliance andsuf focating, destroy the door lock
and childproof lock (if fitted). Y ou received your new appliance in
a protective shipping carton. All packaging materials are environmentally friendly and...

en
28
en Subjekt to modification
 

  	    
    
	
 	
AQUA-ST
OP guarantee
(does not apply to appliances without Aqua-Stop) In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions: 1.  If our Aqua-Stop system is defective and causes water damage, we will make good the damage for private users.
2.  This liability guarantee is valid for the service life of the appliance.
3.  A prerequisite for the warranty...