Home > Siemens > Dishwasher > Siemens Sf 24e232 Instructions For Use

Siemens Sf 24e232 Instructions For Use

    Download as PDF Print this page Share this page

    Have a look at the manual Siemens Sf 24e232 Instructions For Use online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 428 Siemens manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							en21
    Spray
     arms
    Lime  and remnants of food in the washing
    water can block the nozzles in the spray arms 
    22  and 23 and the arm
    mountings .
    Inspect the nozzles in the spray arms for blocked holes due to remnants offood.
    If necessary , pull the lower arm 23
    upwards and lift it of f.
    Unscrew the upper spray arm 22.
    Clean both spray arms under running 
    water.
    Refit the spray arms. Ensure that the lower arm has locked into place and the upper one is screwed tight. Pump
     *
    *  on applicable models
    Larger remnants of food that have notbeen trapped by the filters and have been left in the water can cause a blockage in the pump. The water is no longer pumped out of the dishwasher and it can be seencovering the filter .
    Proceed as follows:
    First, always disconnect the appliance from the power supply .
    Ladle out as much water as possible.
    Remove the filters 25.
    Undo the screw in the cover (T orx T 20)
    and remove the cover .
    Inspect the inside and remove any obstructions that you find.
    Re-insert the cover and screw down.
    Re-insert the filters and screw down.
    Torx T20
    2
    1
      
    						
    							en
    22 Fault
     finding
    Resolving  minor problems
    yourself Experience  has shown that you can
    resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer . Not
    only does this save costs, but it alsomeans that the appliance is available for use again that much sooner . The following
    list of common occurrences and their remedies should help you identify the causes of most problems. Problems  ...
    Attention
    Remember:  Repairs may be
    carried out by a technician only .
    If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare partsmay cause considerable damage and put the user at considerable risk.
    ...  when the appliance
    is switched on
    The  appliance does not start.
    The mains fuse has tripped.
    The appliance plug has not been inserted.
    The appliance door has not been shut properly .
    The tap has not been turned on.
    The filter on the water supply hose is blocked.Switch off the appliance and pull
    out the mains plug. T urn off the
    tap. Then clean the filter which issituated at the connection of the supply hose. Finally , restore the
    power , turn on the tap and switch
    on the appliance.
    ...  with the appliance itself
    Lower  spray arm rotates with
    difficulty
    Spray arm is blocked by small items or food remains.
    Lid in detergent compartment cannot be closed
    Detergent compartment has been overfilled.
    Mechanism is clogged with remnants of detergent. Indicator lamps do not extinguish after washing has finished.
    Indicator lights flash after the programme has started.
    No programme selected.
     Indicator lamps do not extinguish after washing has finished
    Main switch is still set to ON.
    ªCheck water supplyº display 5
    lights up.
    T ap turned of f.
    Water supply interrupted.
    Filter in the water supply blocked.
    Supply hose kinked.
     
    						
    							en23
    Remnants of detergent stuck inside dispenser
    Compartment was damp when it was filled up with detergent. Compartment must be dry beforedetergent is added.
    Water remains inside appliance
    after programme has ended
    Blockage or kink in drainage hose.
    Pump is jammed.
    Filters are blocked.
    The programme is still running. W ait for the programme to end.
    Perform ªResetº function.
    ...  during washing
    Unusual  amount of foam is created
    Normal washing up liquid has been poured into the rinse-aid 
    container.
    Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next washing cycle.
    Appliance stops suddenly while washing is taking place
    Cut in electricity supply to appliance.
    Water supply has been
    interrupted.
    Knocking sound can be heard while washing is taking place
    A spray arm is knocking against the dishes inside the appliance.
    Rattling sound can be heard while washing is taking place
    Crockery has not been stacked properly inside the appliance.
    Knocking sound coming from inlet valves
    This is caused by the way the water pipes have been laid and ithas no ef fect upon the way the
    appliance functions. There is noremedy for this. ...
     with the dishes, cutlery , etc.
    Remnants of food are stuck to the
    dishes, cutlery , etc.
    Dishwasher was not loaded properly. Jets of water could not
    reach all parts of the dishes, etc.
    T oo many items in the rack.
    Items in the rack were touching each other .
    Not enough detergent was added to dispenser .
    Selected wash programme was not intensive enough.
    Rotation of spray arm was obstructed by dish, etc.
    Nozzles in spray arm are blocked by remnants of food.
    Filters are blocked.
    Filters have been incorrectly fitted.
    Waste-water pump is jammed.
    Plastic items are discoloured
    Not enough detergent was added to dispenser .
    White stains are left on crockery ,
    glasses have a milky appearance
    Not enough detergent was added to input compartment.
    Amount of rinse-aid was set too 
    low.
    Although water is quite hard, no salt has been put in appliance.
    W ater softener was set too low .
    Lid on salt container is not screwed tight.
    If you used a phosphate-free detergent, try a detergent containing phosphates and compare results.
    Dishes, cutlery, etc. have not been
    dried
    Selected programme did not include drying function.
    Amount of rinse-aid was set too 
    low.
    Items were removed from dishwasher too soon.
     
    						
    							en
    24
    Glasses have a dull appearance
    Amount of rinse-aid was set too 
    low.
    T ea stains or traces of lipstick have
    not been completely removed
    Detergent does not have a suf ficient bleaching ef fect.
    Washing temperature was set too
    low.
    T races of rust on cutlery
    Cutlery is not suf ficiently rustproof.
    Salt content in washing water is too high.
    Lid on salt container is not screwed tight.
    Too much salt was spilt while
    filling container .
    Glasses become clouded and discoloured; coating cannot be wiped off
    Unsuitable detergent was used.
    Glasses are not dishwasher-proof.
    Smears left behind on glasses and cutlery; glasses have acquired a metallic appearance
    Amount of rinse-aid set too high. Customer
     Service
    Please  call your local service agent, if you
    are not able to resolve any problem yourself. The name of your nearest service agent is shown in the Customer Service address list. When you call, please provide details of the model number (1) and the production (FD) number (2) which are shown on the nameplate 
    31 on the
    appliance door .
    FD
    1 2
    Warning Please note that a visit by the customer service technician in the event of a fault or one ofthe problems previously discussed is not free of charge
    even during the warranty
    period.
     
    						
    							en25
    Information
    Notes  on comparison tests
    You  will find details of the conditions for
    the comparison tests on the additional ºNotes on comparison testsº sheet. The consumption values for the relevant programmes are given in the introduction. General
    Built-under and integrated appliances which are subsequently installed as free-standing appliances must be secured to prevent them from falling over , e.g. by screwing them to the wall
    or by installing them under a continuous worktop which is screwed to the adjoining units.
    For Swiss version only: The appliance can be installed without dif ficulty between wooden and plastic
    walls in a kitchen range. If the applianceis not connected via a plug, theinstallation side must feature an all-pole disconnector with a contact gap of at least 3 mm in order to satisfy therelevant safety regulations. Installation
    The dishwasher must be connected bya qualified technician to ensure correctoperation. The specifications for supply ,
    drainage and connected load must fulfilthe required criteria as stated in the following paragraphs or in the installation instructions. Install the appliance in the following sequence: ± Check the delivery ± Install the appliance ± Connect the waste water ± Connect the fresh water± Connect the power supply Delivery Y our dishwasher was checked at the
    factory to ensure that it was in perfect working order . This may have left some
    small water stains in the dishwasher .
    These will disappear after the first rinse cycle. Installation The required installation dimensions can be found in the installation instructions. Using the height-adjustable feet, adjust the appliance until it is level. Ensure that the appliance is standing firmly .
    Waste  water connection
    See  the installation instructions for the
    required connection steps. If required,attach a siphon with drainage spigot. Using the enclosed parts, connect the waste water hose to the drainage spigot of the siphon. Ensure that the drainage hose is notkinked, crushed or twisted (ensure that there is no sealing cover which prevents the waster water from flowing away!).
     
    						
    							en
    26
    Fresh
     water connection
    Using  the enclosed parts, connect the
    fresh water connection to the tap according to the installation instructions. Ensure that the fresh water connection isnot kinked, crushed or twisted. When replacing the appliance, always connect a new water supply hose to the water supply . The old supply hose must
    not be re-used. W ater pressure:
    Minimum 0,05 MPa (0,5 bar) ± maximum 1 MPa (10 bar). If the water pressure is higher , install a
    pressure reducing valve. Flow rate:Minimum of 10 litres per minute.W ater temperature:
    W e recommend that you use cold water .
    If you do use hot water , the temperature
    should not exceed 60  5C.
    Electrical  connection
    Connect  the appliance only to 230 V
    alternating current via a correctly installed socket with protective conductor .
    See rating plate for required fusing 
    31 . 
    The socket must be attached near the dishwasher and be freely accessible. The connection may be modified by an electrician only .
    Use only a residual-current-operated circuit-breaker which features the 
    symbol. Only this circuit breaker guarantees compliance with the currentlyvalid regulations. Removing
     the appliance
    It  is essential, when removing the
    appliance, to observe the following sequence: First, disconnect the appliance from the power supply .
    Pull out the mains plug. T urn of f the water supply .
    Disconnect the waste water and freshwater connections. Loosen the fastening screws under theworktop. If fitted, remove the base panel. Pull out the appliance, carefully pulling the hose behind. 
    Transporting  the dishwasher
    Drain  water from the dishwasher . Secure
    all loose parts. The appliance should only be transported in an upright position.
    If the appliance is not kept upright during transport, any water left inside may seep into the control module andcause subsequent errors with programme functions.
    Drain the appliance according to the following steps:
    T urn on the tap.
    Close the door .
    Select ECO programme.
    Switch on the main switch.
    Wait until approx. 4 minutes
    have elapsed.
    Rotate programme selector to the Reset position.
    After another minute switch of f
    the appliance.
    T urn of f the tap.
    Protection  from freezing
    temperatures If  the appliance is installed in a location
    where there is a risk of freezing temperatures (e.g. in a holiday home), allwater must be completely drained out of the interior (see ªT ransporting the
    dishwasherº). T urn OFF the tap, disconnect the supply
    hose and allow to drain.
     
    						
    							en27
    Waste
     disposal
    Disposal Old  appliances are not worthless rubbish.
    V aluable raw materials can be reclaimed
    by recycling old appliances. Pull out the mains plug of the redundant appliance. Cut of f the power cord and
    discard with mains plug.T o prevent children from locking
    themselves in the appliance andsuf focating, destroy the door lock
    and childproof lock (if fitted). Y ou received your new appliance in
    a protective shipping carton. All packaging materials are environmentally friendly and recyclable. Please contribute to a better environmentby disposing of packaging materials in an environmentally-friendly manner . All plastic
    parts of the appliance are identified byinternationally standardised symbols (e.g. >PS< polystyrene).When the appliance is being disposed of, the plastic waste can be sorted for environmentally-friendly recycling. Please ask your dealer or inquire at your local authority about current means of disposal. Disposal  of the packaging
    Please dispose of the packaging
    material in an environmentally friendly manner .
    Keep children away from shipping carton and packaging components. Danger of suf focation from folding
    cartons and plastic film.
     Corrugated cardboard consistsmainly of wastepaper .
     The moulded polystyrene parts donot contain any chlorofluorohydrocarbons.
     The polyethylene film (PE) consists partly of secondary raw materials. 
    The wooden frames (if fitted) aremade of untreated residual wood.
     The hoops (if fitted) consist of polypropylene (PP).
    Disposal  of redundant
    appliances
    Make  redundant appliances unusable
    to prevent subsequent accidents.
    Dispose of the appliance in an environmentally friendly manner .
    Warning
    Children could become locked in the appliance (risk of suf focation) or find
    themselves in other dangerous situations.Therefore: Pull out the mains plug, sever and dispose of the power cord.Destroy the door lock so that the door can no longer be closed.
    This appliance is labelled in accordance with European Directive 2002/96/EG concerning used electrical and electronic appliances (waste electrical and electronic equipment ± WEEE). The guideline determines the framework for the returnand recycling of used appliances as applicable throughout the EU.
      
    						
    							en
    28
    en Subjekt to modification
     
    						
    							  	    
        
    	
     	
    AQUA-ST
    OP guarantee
    (does not apply to appliances without Aqua-Stop) In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions: 1.  If our Aqua-Stop system is defective and causes water damage, we will make good the damage for private users.
    2.  This liability guarantee is valid for the service life of the appliance.
    3.  A prerequisite for the warranty claim is that the appliancehas been correctly installed and connected with Aqua-Stop according to our instructions.  ªThis also includes the correct installation of the Aqua-Stop extension (original accessory).º Our warranty does not extend to defective feed lines or fittings up to the Aqua-Stop connection on the tap.
    4.  If your appliance is fitted with Aqua-Stop, you can leave your appliance unattended during operation and leave the tapturned on afterwards. The tap should only be turned of f if you
    are absent from home for a prolonged period, e.g. severalweeks holiday .
    Siemens-Electroger‚te GmbHCarl-W ery-Straûe 34, 81739 M˜nchen
      
        	  		    
      	 GB    0844 / 8928999
    IE    01450 2655 Calls
     from a BT landline will be charged at up
    to 3 pence per minute. A call set±up free of up to 6 pence may apply .
    Pease  find the contact data of all countries in the enclosed
    customer service list. Internet: www .siemens±home.com
                                                                        
     
     
    						
    All Siemens manuals Comments (0)

    Related Manuals for Siemens Sf 24e232 Instructions For Use