Siemens Se 60t391 Eu Instructions For Use

en
21
Programme overview
Soups, 
souffl‡s, 
sauces, 
potatoes, 
pastries, 
rice, eggs, 
fried foodSoups,
potatoes,
pastries,
rice, eggs,
fried foodCoffee,
cake, milk,
sausage, cold
drinks,
saladsRinse if the
utensils have
been left for
several days
prior to wash-
ing in the dish
washer
Large -> small
AUTO
SUPER
WASHAUTO
DELICATE
WASHQUICK
WASHPRERINSE
ONLY AUTO WASH Type of utensil
e.g. porcelain,
pans,
cutlery,
glasses,
etc.Hard-
wearingMixed
Fragile
Mixed
Type of food
remains
e.g.
Amount of
food...

en
22
Programme  data
The programme data (duration, energy
and water consumption) can be found in
the summary of instructions and refers to
standard conditions. Greater deviations
may be caused by:
different quantities of utensils
inlet temperature of the water
water pressure
ambient temperature
mains voltage tolerances
and appliance-specific tolerances
(e.g. temperature, water flow rate, etc.)
Only ranges can be indicated for the
automatic programmes.
The water consumption values refer
to water hardness...

en
23
Within an option/basic setting there are
several possible settings that can be
selected using the buttons ± or + 
3.
A selected setting is applied by
changing to the next option/basic
setting using the button M/OK 
2.
If a setting has been changed using
the buttons ± or + and stored using
M/OK 
2, the message ªValue Storedº
will be displayed and the display returns
to the Main Menu.
Timer programming
You can delay the programme start by
24 hours in steps of 
 minutes.
If the option ªTime...

en
24
Buzzer Volume
You can vary or even completely
switch off the volume of the acoustic
end-of-programme signal.
If the option ªBuzzer Volumeº is chosen
the display shows ªBuzzer 6º (factory
setting).
You can change this value to 0
(acoustic signals switched off) or
to values between 1 (quiet) and 6
(loud). A short buzz demonstrates
the currently chosen volume level.
Adding Rinse Aid
You can set the amount of rinse aid
added.
If the option ªAdding Rinse Aidº is
chosen the display shows ªRinse Aid 4º...

en
25
Standard Programmes
In addition to the rinse programmes
available in the Main Menu you can
choose among the following standard
programmes from the programme
ªNormalº:
Extra,
Eco 50,
Eco 45,
Normal 45.
Set the desired programme and start
the selected programme by pressing
the Start Button 
4.
If you do not want to use any of the
displayed standard programmes return
to the Main Menu by using the button
M/OK 
2.
If you want to cancel the selection
of a standard programme in the Main
Menu press the...

en
26
Aqua sensor *
* on applicable models
The Aqua sensor is an optical measuring
device which measures the turbidity of the
rinsing water. A light barrier can detect
dissolved food remnants in the water, e.g.
egg, fat and oats.
The Aqua sensor is used according to
the programme. When the Aqua sensor
is active, ºcleanº rinsing water may be
transferred into the next rinsing bath
and/or the temperature adjusted. If the
turbidity is greater, the water is drained
and is replaced with fresh water. In this...

en
27
Interrupting the programme
In order to interrupt the programme,
open the door. In order to avoid water
escaping, only open the door slightly
first.
The message ªCancel Programmeº
will be displayed, alternating with
the message ªClose the doorº,
the remaining programme time,
the selected programme, and the
current programme phase.
In order to interrupt, do not in any
circumstance press the button ± 
3
ªCancel Programmeº because this will
not allow the programme to continue!
To continue the...

en
28
Maintenance  and care
A regular inspection and maintenance
of your machine will help to prevent faults.
This saves time and prevents problems.
Therefore you should occasionally have
a careful look inside your dishwasher.
Overall  condition
of the machine
Check spray arm for grease and
limescale deposits.
If you find such deposits:
Fill the detergent dispenser with
detergent, start the appliance without
utensils in the programme which has
the highest wash temperature.
Clean the appliance with...

en
29
Spray arms
Lime and remnants of food in the washing
water can block the nozzles in the spray
arms 
23 and 24 and the arm
mountings .
Inspect the nozzles in the spray arms
for blocked holes due to remnants of
food.
If necessary, pull the lower arm 24
upwards and lift it off.
Unscrew the upper spray arm 23.
Clean both spray arms under running
water.
0 1 23
Refit the spray arms. Ensure that the
lower arm has locked into place and the
upper one is screwed tight.
 

en
30
Pump *
*
 on applicable models
Larger remnants of food that have not
been trapped by the filters and have been
left in the water can cause a blockage in
the pump. The water is no longer pumped
out of the dishwasher and it can be seen
covering the filter.
Proceed as follows:
First, always disconnect the appliance
from the power supply.
Ladle out as much water as possible.
Remove the filters 26.
Undo the screw in the cover (Torx T 20)
and remove the cover.
Inspect the inside and remove any...