Siemens Se 60t391 Eu Instructions For Use

							en
21
Programme overview
Soups, 
souffl‡s, 
sauces, 
potatoes, 
pastries, 
rice, eggs, 
fried foodSoups,
potatoes,
pastries,
rice, eggs,
fried foodCoffee,
cake, milk,
sausage, cold
drinks,
saladsRinse if the
utensils have
been left for
several days
prior to wash-
ing in the dish
washer
Large -> small
AUTO
SUPER
WASHAUTO
DELICATE
WASHQUICK
WASHPRERINSE
ONLY AUTO WASH Type of utensil
e.g. porcelain,
pans,
cutlery,
glasses,
etc.Hard-
wearingMixed
Fragile
Mixed
Type of food
remains
e.g.
Amount of
food remains
Condition of
food remains
Wash
programme
Programme
progressVery
small
Very
adhesiveSlightly adhesive
The programme progress is
optimised and adjusted
according to the appliance
load and degree of soiling
on the utensils.
DryingPrerinse
Clean
Intermedi-
ate wash
Final wash 60
 ± 70
45
 ± 55
35
 ± 45
45

 
						

							en
22
Programme  data
The programme data (duration, energy
and water consumption) can be found in
the summary of instructions and refers to
standard conditions. Greater deviations
may be caused by:
different quantities of utensils
inlet temperature of the water
water pressure
ambient temperature
mains voltage tolerances
and appliance-specific tolerances
(e.g. temperature, water flow rate, etc.)
Only ranges can be indicated for the
automatic programmes.
The water consumption values refer
to water hardness value 4.
Selecting options/
standard settings
Operating principle
Remote Options **
The dishwasher installs itself automatically
during the first use within a serve@Home
network. In some cases however, it might
become necessary to start the enrolment
process anew.
If the option ªRemote Optionsº is
selected, the message ªEnrol Deviceº
will be displayed. By pressing the
button + 
3 you enrol the device
again at the gateway. After successfully
enrolling the device the message
ªAuto Washº will be displayed.
If the enrolment is unsuccessful the
display shows ªno gateway foundº.
** Only with installed interface
From the Main Menu you can select the
following options/settings by repeatedly
pressing the button M/OK 
2:
Timer programming
Remote Control**
Reduce Time
Drying Level
Buzzer Volume
Adding Rinse Aid
Water Hardness
Language
Standard Programmes
Remote Setting**
** Only with installed  interface
 
						

							en
23
Within an option/basic setting there are
several possible settings that can be
selected using the buttons ± or + 
3.
A selected setting is applied by
changing to the next option/basic
setting using the button M/OK 
2.
If a setting has been changed using
the buttons ± or + and stored using
M/OK 
2, the message ªValue Storedº
will be displayed and the display returns
to the Main Menu.
Timer programming
You can delay the programme start by
24 hours in steps of 
 minutes.
If the option ªTime Pre-selectº is
chosen the display shows ªDelay start:
00 minsº.
Set the desired time.
Return to the Main Menu by pressing
M/OK 
2 and start the required
programme by pressing the Start Button
4.
Close the door. This starts the time
counting backwards.
When the set time has elapsed the
programme will start automatically.
Until the programme starts you are able
to change the set time and programme.
To do this, use the button ± 
3 to
return to the Main Menu and change
the settings. Then start the programme
again.
In order to delete the pre-selected time,
set the time back to ªDelay start:
00 minsº.
Remote Control**
After choosing the option ªRemote
Controlº the display will show ªRemote
Control: Offº (factory setting)
You activate this option by selecting
ªRemote Control: Onº.
** Only with installed serve@Home
interface
Reduce Time
The Auto Programmes allow you to reduce
the run time of the programmes. However,
in order to achieve an optimal cleaning
result, the water and energy consumption
will be increased.
If the option ªReduce timeº is chosen
the display shows ªReduce time: Offº
(factory setting).
Select ªReduce time: Onº.
Return to the Main Menu by pressing
M/OK 
2 and start the required
programme by pressing the Start Button
4.
If you do not want to use ªReduce
timeº the next time you use the
dishwasher, you must deselect this
option.
Drying Level
If the option ªDrying Levelº is chosen
the display shows ªNormal dryingº
(factory setting).
Alternatively you can select ªEco
dryingº or ªExtra dryingº.
The option ºExtra dryingº increases
the temperature during rinsing in all
programmes. (Please take care with
delicate dishes.)
 
						

							en
24
Buzzer Volume
You can vary or even completely
switch off the volume of the acoustic
end-of-programme signal.
If the option ªBuzzer Volumeº is chosen
the display shows ªBuzzer 6º (factory
setting).
You can change this value to 0
(acoustic signals switched off) or
to values between 1 (quiet) and 6
(loud). A short buzz demonstrates
the currently chosen volume level.
Adding Rinse Aid
You can set the amount of rinse aid
added.
If the option ªAdding Rinse Aidº is
chosen the display shows ªRinse Aid 4º
(factory setting).
Change this setting only if there are
streaks (reduce the value) or water
stains (increase the value) remaining
on the dishes.
You can choose a value between 0
and 6.
Water Hardness
Before starting the appliance for the first
time or in case of changes in the water
hardness, the dishwashers softening
system must be set to the hardness of
your mains water supply. Follow the
instructions set out in the chapter ªSet-up
of the Softening Systemº.
Language
You can change the language selected
when the appliance was started for the
first time (see chapter ªBefore Starting
The Device For The First Timeº).
If the option ªLanguageº is chosen the
display shows several language
abbreviations. The abbreviation of the
currently selected language is flashing.
In order to choose a different language,
press ± or + 
3 until the desired
language appears.
Confirm the language selection by
pressing M/OK 
2.
All following optical character messages
will be displayed in the selected language.
 
						

							en
25
Standard Programmes
In addition to the rinse programmes
available in the Main Menu you can
choose among the following standard
programmes from the programme
ªNormalº:
Extra,
Eco 50,
Eco 45,
Normal 45.
Set the desired programme and start
the selected programme by pressing
the Start Button 
4.
If you do not want to use any of the
displayed standard programmes return
to the Main Menu by using the button
M/OK 
2.
If you want to cancel the selection
of a standard programme in the Main
Menu press the button ± ªBackº.
The selected standard programme will
be displayed. By pressing the buttons
± or + the Main Menu will display the
programme ªAuto Washº.
Type of DishesExtraEco 50 Eco 45 Normal 45
Mixed Dishes
Amount of food
remnants
State of food
remnantLittle to Many
Lightly Adhesive
You can find the corresponding programme data (length of time, energy and water
consumption) in the short manual.
We recommend on principle to use the Auto Programmes because they keep the
water and energy consumption as low as possible due to the variable programme run.
In the case of the standard programmes on the other hand, the programme run is
predetermined.
 
						

							en
26
Aqua sensor *
* on applicable models
The Aqua sensor is an optical measuring
device which measures the turbidity of the
rinsing water. A light barrier can detect
dissolved food remnants in the water, e.g.
egg, fat and oats.
The Aqua sensor is used according to
the programme. When the Aqua sensor
is active, ºcleanº rinsing water may be
transferred into the next rinsing bath
and/or the temperature adjusted. If the
turbidity is greater, the water is drained
and is replaced with fresh water. In this
way the water consumption is reduced by
approx. 4 litres for utensils which are ºlessº
dirty.
Optical indicator during
operation *
* With some models
During the rinse programme a light point
appears on the floor below the devices
door. Only open the dishwasher door
when the light point has disappeared.
In the case of built-in dishwashers with
flush front the light point will not be visible.
Start programme
Before starting check again whether the
spray arms can move freely.
Press the button ªStartº 4 in the Main
Menu.
The message ªClose the doorº will be
displayed, alternating with a display of
the expected programme time. This time
is only approximate. The running time
indicated at the start of the set programme
will probably be required. During the
programme run the remaining time will be
adjusted according to the water supply
temperature and the amount and soil level
of the dishes.
If you have chosen a time for the
programme start the message ªClose the
doorº will appear when the programme is
started, alternating with the pre-selected
time.
Close the door.
The programme or the pre-selected time
respectively will run.
The programme and other settings can still
be changed as long as the door is still
open after pressing the button ªStartº 
4.
By pressing the button M/OK 
2
ªReturnº, return to the Main Menu where
you can change the settings. Finally start
the programme again.
When the door is closed after the start and
the programme has already started, you
will have to interrupt the programme in
order to change any settings (see ªCancel
Programmeº).
 
						

							en
27
Interrupting the programme
In order to interrupt the programme,
open the door. In order to avoid water
escaping, only open the door slightly
first.
The message ªCancel Programmeº
will be displayed, alternating with
the message ªClose the doorº,
the remaining programme time,
the selected programme, and the
current programme phase.
In order to interrupt, do not in any
circumstance press the button ± 
3
ªCancel Programmeº because this will
not allow the programme to continue!
To continue the programme, close
the door. The programme will continue
automatically.
In the case of a warm water supply or
when the appliance is already heated,
leave the door slightly ajar for a few
minutes before closing it. Otherwise the
door can spring open again due to the
warm air trapped in the devices interior.
Terminating the programme
Open the door. First open the door only
slightly in order to avoid water spraying
out.
The message ªCancel Programmeº
will be displayed, alternating with
the message ªClose the doorº,
the remaining programme time,
the selected programme, and the
current programme phase.
In order to cancel the programme,
press ± 
3 ªCancel Programmeº. 
ªTo cancelº and ªClose the doorº are
displayed.
Close the door. The water remaining in
the devices interior will be pumped off.
Once the pumping off has finished
a buzzer will sound 5 times.
Open the door. ªEndº is briefly
displayed, the appliance automatically
switches off after 5 seconds.
End of programme
As soon as the programme has finished
a buzzer will sound 5 times.
Open the door. ªEndº is briefly
displayed, the appliance automatically
switches off after 5 seconds.
If the door is not opened, an acoustic
signal sounds every 10 minutes for one
hour.
After letting the device cool down take
out the dishes.
Note
For an optimum drying of the dishes wait
for 15 minutes after the programme has
finished before you open the door and
empty the dishwasher. During this time the
possibly remaining water on the dishes
can evaporate and condense on the sides
of the devices interior.
Note
If the device becomes disconnected from
the power supply during operation (e.g.
it is switched off or there is a power cut),
all settings remain stored. Operation
will resume automatically once the power
supply has been restored.
 
						

							en
28
Maintenance  and care
A regular inspection and maintenance
of your machine will help to prevent faults.
This saves time and prevents problems.
Therefore you should occasionally have
a careful look inside your dishwasher.
Overall  condition
of the machine
Check spray arm for grease and
limescale deposits.
If you find such deposits:
Fill the detergent dispenser with
detergent, start the appliance without
utensils in the programme which has
the highest wash temperature.
Clean the appliance with detergents/
appliance cleaners which are particularly
suitable for use with dishwashers.
Regularly wipe the door seal with
a damp cloth to remove deposits.
Never use a steam cleaner to clean your
dishwasher. The manufacturer is not liable
for any consequential damage.
Attention!
Never use other chlorinated household
detergents! Health hazard!
Special  Salt
When the salt level is low, your
dishwasher displays a message in the
window.
Rinse aid
When the rinse aid level is low, your
dishwasher displays a message in the
window.
Filters
The filters 26 prevent larger remnants of
food or other objects from getting inside
the pump. This residue can occasionally
clog up the filters.
The filter system consists of a filter
cylinder, a flat fine filter and, depending on
the model, a microfilter (*).
Inspect the filters for obstructions every
time the dishwasher has been used.
By unscrewing the filter cylinder, you
can remove the filter system. Remove
any food remnants and clean the filters
under running water.
Reassembly:
Insert the filter system and screw down
with the filter cylinder.
 
						

							en
29
Spray arms
Lime and remnants of food in the washing
water can block the nozzles in the spray
arms 
23 and 24 and the arm
mountings .
Inspect the nozzles in the spray arms
for blocked holes due to remnants of
food.
If necessary, pull the lower arm 24
upwards and lift it off.
Unscrew the upper spray arm 23.
Clean both spray arms under running
water.
0 1 23
Refit the spray arms. Ensure that the
lower arm has locked into place and the
upper one is screwed tight.
 
						

							en
30
Pump *
*
 on applicable models
Larger remnants of food that have not
been trapped by the filters and have been
left in the water can cause a blockage in
the pump. The water is no longer pumped
out of the dishwasher and it can be seen
covering the filter.
Proceed as follows:
First, always disconnect the appliance
from the power supply.
Ladle out as much water as possible.
Remove the filters 26.
Undo the screw in the cover (Torx T 20)
and remove the cover.
Inspect the inside and remove any
obstructions that you find.
Re-insert the cover and screw down.
Re-insert the filters and screw down.
Torx T20
2
1
Fault finding
Resolving minor problems
yourself
Experience has shown that you can
resolve most problems that arise during
normal daily usage yourself, without
having to call out a service engineer. Not
only does this save costs, but it also
means that the appliance is available for
use again that much sooner. The following
list of common occurrences and their
remedies should help you identify the
causes of most problems.
Problems ...
Attention
Remember: Repairs may be
carried out by a technician only.
If a component has to be replaced,
ensure that only original spare
parts are used. Improper repairs
or use of non-original spare parts
may cause considerable damage
and put the user at considerable
risk.
... On Switching On
Wrong Language Selected
The following steps return you to the
language selection:
1. Switch off the device.
2. Switch on the device. Press the button
M/OK 
2 repeatedly until the
language selection appears in the
display.
3. Select the language and confirm your
selection.