Home > Siemens > Dishwasher > Siemens Se 25m276 Eu Instructions For Use

Siemens Se 25m276 Eu Instructions For Use

    Download as PDF Print this page Share this page

    Have a look at the manual Siemens Se 25m276 Eu Instructions For Use online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 428 Siemens manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							en11
    Top
     basket with side levers
    (Rackmatic)
    Pull  out the top basket.
    To lower  the basket, press in one lever
    and then the other situated on the left and right of the basket exterior , holding
    the basket firmly on the sides of theupper edge to prevent it from fallingdown.
    To  raise  the basket, hold the basket on
    the sides of the upper edge and lift it up.
    Before re-inserting the basket again, ensure that it is at the same height on both sides. Otherwise, the appliancedoor cannot be closed and the upper spray arm will not be connected to the water circuit. Detergent
    Y ou can use commercially available liquid
    or powder proprietary detergents fordishwashers or T ABS (do not use
    handwash!). If phosphate-free detergents are used with hard tap water , white deposits may be
    deposited more easily on utensils and the container walls. This can be remedied by adding more detergent. See detergent packaging to determine whether a detergent is suitable for silver parts. If you have any other questions, we recommend that you contact the helplinesof the detergent manufacturers. Detergent  dispenser with
    dosing aid The  graduated detergent dispenser helps
    you pour in the correct amount. Lower line: 15 ml
    Middle line: 25 ml
    Full to the brim: 40 ml
    If the detergent dispenser 
    30  is still
    closed, press the lock 
    28  to open the
    detergent dispenser .
    Adding  detergent
    Fill the dispenser 30  with detergent.
    Dosage: see manufacturer ’s
    instructions on the detergent packaging.
    Note
    The cleaning tabs from various manufacturers exhibit dif fering dissolving
    properties, so washing power may notdevelop fully during short programmes and there may be undissolved cleaning agent residue. It is recommended to usewashing powder for these programmes. The Intensive programme (on some models) requires one tab only . When using
    washing powder , you can apply some
    of this cleaning agent to the inside ofthe appliance’ s door.
      
    						
    							en
    12
     Reduce costs!
    If your dishes are only moderately dirty ,
    you may be able to use less detergent than recommended.
    Close the lid on the detergent compartment. Press down the lid (1) until it clicksshut (2).
    If you are using detergent in tablet form, read the manufacturer ’s
    recommendations on the packaging inorder to  determine where the tablets should be placed inside the dishwasher (e.g. in cutlery basket, detergent compartment, etc.). Make sure that the lid on the detergent compartment is closed, even if you are using tablets. auto
     3in1
    The  use of so-called combined detergent
    products may make the use of rinse aid and/or salt unnecessary .
    There are currently several types ofcombined detergent products available.
    2in1:  They contain detergent and rinse
    aid  or salt function.
    3in1:  They contain detergent, rinse aid
    and  salt function.
    4in1 : They contain a detergent,
    rinse-aid, salt function  and an additional
    glass protection component.
    In addition, other combined products with a comparable ef fect are offered according
    to the manufacturer .
    >>>  Always check the type of detergent
    or combined product which you are using!
    Always follow the operating instructionsor the information on the packaging.
    The rinse programme is automaticallyadjusted in order to obtain the best possible rinsing and drying result. Observe the following important information if using combined cleaning products:
    Regeneration salt is not required up to a water hardness of 21  dH (37  fH,
    26  Clarke, 3.7 mmol/l) only . No other
    settings on the appliance are required.
    Salt is still required if the water hardness is  above 21 dH (37  fH,
    26 Clarke, 3.7 mmol/l). Fill the salt
    dispenser with salt 
    24 and select
    setting 6 on the water softening system.
    If in doubt, please contact the detergent manufacturer , especially if:
    the utensils are very wet at the end ofthe programme.
    limescale forms.
       
    						
    							en13
    Note
    Optimum rinsing and drying results can be obtained by using standard detergents in conjunction with separate application ofsalt and rinse aid. Observance of the operating instructions or information on the packaging of the combined detergents determines their 
    effectiveness.
    Note
    Even if the rinse aid and/or salt refill indicator is lit, the rinse programme runscorrectly when 3in1 products are used. If the rinse aid refill indicator 
    9 or salt
    refill 
    8 indicator is defective and you
    would like to switch it of f, proceed as
    follows: Switching  the rinse aid refill
    indicator off and on 
    You  can switch the rinse aid refill indicator
    9 on or of f. This function can be
    changed as follows.
    Close the door .
    Hold down the programme button 4
    and press the main switch 1 until the
    digital display lights up, then release the buttons.
    3 is indicated on the digital display
     (rinse aid refill indicator on).
    By pressing the programme button
    4, you can switch of f  or switch
    on 
     the rinse aid indicator .
    Switch off the main switch 1;
    the setting is saved. Switching
     the salt refill
    indicator / water softening system off and on
    Close  the door .
    Hold down the programme button B
    and switch on the main switch 
    1,
    then release the buttons. The illuminated button 
    B  and the
    factory-set value 
     on the digital
    display flash. T o change the setting: press the
    programme button 
    B  .
    Each time the button is pressed, the set value increases by one; when the value
     is reached, the display jumps
    back to 
     (the salt refill indicator /
    water softening system has been switched of f).
    Switch off the main switch 1.
    The set value is stored within the
    device.
    Approx. 4 litres of water are required to regenerate the water softening system. As a result, the water consumption per
    rinse cycle increases by 0 to maximum 4 litres depending on the water hardness
    setting.
    Note
    If you use the detergent and rinse aid separately or switch from combined detergents to standard cleaning products, ensure that the rinse aid refill indicator has been switched on and the water softening system has been set to the correct waterhardness.
           
    						
    							en
    14 Overview
     of programmes
    The max. possible number of programmes is illustrated in this overview . 
    The corresponding programmes for your appliance can be found on the fascia.
    Cof fee, cake, milk,
    sausage, cold drinks, salads
    Soups, souf
    flés,
    potatoes, pastries, rice, eggs,fried food Delicate
    T
    ype of Dishes
    e.g. porcelain, pans, 
    cutlery,glasses, etc.
    T ype of food
    remnants e.g. Programme- sequence
    Dry
    Clean 55 
    Clean
    40 
    PrerinseClean
    55 
    Clean
    45 
    Soups,
    potatoes, pastries,
    rice, eggs, fried food
    Wash programme V
    ery little
    Little
    Large
    Amount offood remnants State of food remnantIntensive
    70Eco
    50  Gentle
    40  Quick
    45  Prerinse
    MixedMixed
    Non-sensitive
    Medium Lightly Adhesive
    Very
    adhesive
    Dry
    Clean 65 
    Clean
    50 
    Prerinse
    Dry
    Clean
    70 
    Dry
    Clean
    70 
    Prerinse
    40 
    The programme sequence is
    optimised and adjusted according to the degree of soiling on the utensils.
    Auto
    55 -65 
    Prerinse
    Rinse of f if
    the dishes
    have been stacked
    for several days in the
    dishwash
    er prior to washing.
    Inter-
    mediate
    rinse Inter-
    mediate
    rinse Inter-
    mediate
    rinse Inter-
    mediate
    rinse
           
    						
    							en15
    Programme
     selection
    The  most appropriate programme can be
    identified by comparing the type of crockery , cutlery, etc., as well as the
    amount and condition of food remains, with the details contained in the programme overview .
    Y ou will find the appropriate programme
    information in the introduction.
    Washing  dishes
     Reduce costs!
    If only a small number of dishes have been loaded into the dishwasher , selecting
    a programme that operates at the next lowest temperature will usually suf fice.
    Programme  specifications
    The  programme specifications can be
    found in the summary of instructions. Programme specifications refer to normal conditions. Greater deviations may occur due to:
    varying amounts of dishes
    water supply temperature
    water pipe pressure
    ambient temperature
    mains voltage tolerances
    and the tolerances specific to the appliance (e.g. temperature, amount of water , etc.)
    The water consumption values refer to a set water hardness value of 4. Aqua  sensor *
    * some  models
    The Aquasensor is an optical measuring device (light barrier) which measuresthe turbidity of the rinsing water .
    The Aqua sensor is used accordingto the programme. When the Aqua sensor is active, “clean” rinsing water may be transferred into the next rinsing bathand/or the temperature adjusted. If the turbidity is greater
    , the water is
    drained and is replaced with fresh water . In
    this way water consumption can be reduced by approx. 4 litres. Switching  the dishwasher ON
    Turn on the tap.
    Set main switch 1 to ON.
    Indicators light up according to the last programme that was selected. This same programme will run again if no other programme button 
    6 is
    pressed.
    The numerical display 3 shows the
    expected duration of the programme.
    The programme starts automatically .
    Programme  sequence indicator
    7
    Your dishes are being cleaned.
    Y our dishes are being dried.
    Your dishes are being rinsed.
    Remaining  running time display
    When  the appliance has started, the
    expected programme running time is displayed. The programmed running time is af fected by the water temperature, the
    number of dishes, as well as the degree of soiling. If these conditions are changed, the running time (depending on the selected programme) can vary greatly .
    As the ef fect is not detected until a
    programme is running, the time may be longer or shorter than expected. 
    Time  delay
    You  can delay the start of the programme
    in 1-hour steps up to 24 hours.
    Switch on the appliance.
    Press the timer programming button
    4 until the digital display 3 jumps
    to 
    .
          
    						
    							en
    16
    Keep pressing the timer programming button until the required time isdisplayed.
    T o delete the timer programming,
    keep pressing the button until 
    is displayed. Y ou can change your programme
    selection at any time until the programme starts.
    End  of programme
    The  programme has ended when a figure
     appears in the numerical
    display 
    3.
    Switching  the dishwasher OFF
    Several  minutes after the programme has
    ended:
    Set the main switch 1 to OFF .
    Turn the water tap of f.
    (Does not apply when Aqua-Stop unit has been fitted)
    Remove dishes, etc. when they have cooled down.
    At the end of the programme please open the door fully and not partially when emptying the dishwasher . Any escaping
    water vapour could damage sensitiveworktops. Interrupting  the programme
    Switch off the main switch 1.
    The lit display goes out. The programme is saved.If there is a warm water connection or ifthe machine has already heated up and the appliance door was opened, leave the door open for several minutes andthen close. Otherwise, expansion maycause the appliance door to spring open.
    Switch on the main switch again. Terminating
     the programme
    (Reset)
    Simultaneously  press programme
    buttons 
    A  and C for approx. 3 sec.
    The numerical display indicates 
    .
    The programme sequence lasts approx. 1 min.
    Switch of f the main switch 1.
    Changing  the programme
    When  the appliance is switched on, the
    programme can be changed within minutes. If the programme is changed subsequently , programme sections
    (e.g. Cleaning) which have already startedrun to the end. The new remaining time consists of the remaining time of the previous programme section and the remaining time of the newly selected programme. Intensive  drying
    In  the final rinse the appliance operates
    at a higher temperature and therefore an improved drying result is obtained.(Caution if utensils are fragile!)
    Close the door .
    Hold down programme button A and
    press main switch until 
    1 the digital
    display illuminates.
    Release both buttons.
    The LED for button 
    A  flashes and
    the digital display 
    3 displays the factory
    setting 
     (of f) or  (on).
    To change the setting, press
    programme button 
    A .
    Switch of f the main switch 1.
          
    						
    							en17
    Additional
     functions
    *  on  some models additional functions
    5 can be set with the buttons.
     Soaking *
    The  soaking cycle runs before the main
    programme and must be selected before
    the programme starts. In this additional programme cooking utensils, e.g. pans,bowls, etc., can be soaked and prerinsed in the  bottom basket .
    It is recommended to put approx. 5 g ofdetergent on the door .
     Reduce/save time*
    The  rinsing times and the drying phase
    are reduced. The reduced time  lowers
    the rinsing and drying performance.
     T op basket washing only *
    If  there are only a few utensils (e.g.
    glasses, cups, plates), use the top basket. The bottom basket must be empty! Use slightly less detergent than is recommended for a complete load.
     Bottom basket washing
    only * If  there are only a few utensils (e.g. plates,
    pans, bowls), use the bottom basket. The top basket must be empty! Use slightly less detergent than is recommended for a complete load. Maintenance
     and care
    A  regular inspection and maintenance of
    your machine will help to prevent faults. This saves time and prevents problems. Overall  condition of the
    machine
    Check  washing chamber for grease
    and limescale deposits.
    If you find such deposits:
    Fill the detergent dispenser with detergent, start the appliance withoututensils in the programme which has the highest wash temperature.
    Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers.
    Regularly wipe the door seal with a damp cloth.
    Never use a steam cleaner to clean your dishwasher . The manufacturer is not liable
    for any consequential damage. Regularly wipe the front of the appliance and panel with a damp cloth; water and a little washing-up liquid will suf fice.
    Do not use sponges with a rough surfaceor abrasive detergents, as these could scratch the surfaces.
    Attention!
    Never use other chlorinated household detergents! Health hazard! Salt  and rinse aid
    Check  the refill indicators 8  9.
    If required, top up the salt and/or rinse aid.
    Filters The filters 
    25  prevent larger remnants of
    food or other objects from getting inside the pump. This residue can occasionally clog up the filters. The filter system consists of a filter cylinder , a flat fine filter and, depending on
    the model, a microfilter (*).
         
    						
    							en
    18
    Inspect the filters for obstructions every time the dishwasher has been used.
    By unscrewing the filter cylinder , you
    can remove the filter system. Remove any food remnants and clean the filtersunder running water .
    Reassembly: Insert the filter system and screw down with the filter cylinder .
    Spray arms
    Lime  and remnants of food in the washing
    water can block the nozzles in the spray arms 
    22  and 23 and the arm
    mountings .
    Inspect the nozzles in the spray arms for blocked holes due to remnants of food.
    If necessary , pull the lower arm 23
    upwards and lift it of f.
    Unscrew the upper spray arm 22.
    Clean both spray arms under running 
    water.
    0
    1
    2
    3
    Refit the spray arms. Ensure that the lower arm has locked into place and theupper one is screwed tight.
         
    						
    							en19
    Pump
     *
    *  on applicable models
    Larger remnants of food that have not been trapped by the filters and have been left in the water can cause a blockage in the pump. The water is no longer pumped out of the dishwasher and it can be seencovering the filter .
    Proceed as follows:
    First, always disconnect the appliance from the power supply .
    Ladle out as much water as possible.
    Remove the filters 25.
    Undo the screw in the cover (T orx T 20)
    and remove the cover .
    Inspect the inside and remove any obstructions that you find.
    Re-insert the cover and screw down.
    Re-insert the filters and screw down.
    Torx T20
    2
    1
    Fault finding
    Resolving  minor problems
    yourself Experience  has shown that you can
    resolve most problems that arise during normal daily usage yourself, without having to call out a service engineer . Not
    only does this save costs, but it alsomeans that the appliance is available for use again that much sooner . The following
    list of common occurrences and their remedies should help you identify the causes of most problems. Problems  ...
    Attention
    Remember:  Repairs may be carried out by
    a technician only . If a component has to be
    replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. ...  when the appliance
    is switched on
    The  appliance does not start.
    The mains fuse has tripped.
    The appliance plug has not been inserted.
    The appliance door has not been shut properly .
    The tap has not been turned on.
     
    						
    							en
    20
    The filter on the water supply hose is blocked.Switch of f the appliance and pull
    out the mains plug. T urn off the
    tap. Then clean the filter which issituated at the connection of the supply hose. Finally , restore the
    power , turn on the tap and switch
    on the appliance.
    ...  with the appliance itself
    Lower  spray arm rotates with
    difficulty
    Spray arm is blocked by small items or food remains.
    Lid in detergent compartment cannot be closed
    Detergent compartment has been overfilled.
    Mechanism is clogged with remnants of detergent. Indicator lamps do not extinguish after washing has finished.
     Indicator lamps do not extinguish after washing has finished
    Main switch is still set to ON.
    Remnants of detergent stuck inside dispenser
    Compartment was damp when it was filled up with detergent. Compartment must be dry before detergent is added.
    Refill display does not light up.
    Rinse aid refill indicator switched of f. (see auto 3in1 chapter)
    Salt refill indicator switched of f.
    (see auto 3in1 chapter)
    W ater remains inside appliance
    after programme has ended
    Blockage or kink in drainage hose.
    Pump is jammed.
    Filters are blocked.
    The programme is still running. W ait for the programme to end
    (numerical display will indicate 0).
    Perform “Reset” function.
    ...  during washing
    Unusual  amount of foam is created
    Normal washing up liquid has been poured into the rinse-aid
    container.
    Remove any spilled rinse aid with a cloth as it could otherwise lead to excessive foaming during the next washing cycle.
    Appliance stops suddenly while washing is taking place
    Cut in electricity supply to appliance.
    Water supply has been
    interrupted.
    Knocking sound can be heard while washing is taking place
    A spray arm is knocking against the dishes inside the appliance.
    Rattling sound can be heard while washing is taking place
    Crockery has not been stacked properly inside the appliance.
    Knocking sound coming from inlet valves
    This is caused by the way the water pipes have been laid and it has no ef fect upon the way the
    appliance functions. There is noremedy for this.
     
    						
    All Siemens manuals Comments (0)

    Related Manuals for Siemens Se 25m276 Eu Instructions For Use