Siemens Sc 76m530 Operating Instructions

en11
The max. possible number of programmes is illustrated 
in this overview. The 
corresponding programmes for your appliance can be fo und on the fascia. The 
programme data has been measured in the laboratory acc ording to AS/NSZ 2007.
Overview of programmes
Programme Type of utensils  and soiling Programme  sequencePossible additional optionsProgramme data 
1.) Duration: hs/ mins 
2.) Energy  
consumption in kWh 
3.) Water  consumption in 
litres 
4.) With Aquasensor
ª
Pots and Pans 70° Pots,...

en 
12
Programme selection 
You can select a suitable programme  
according to the type of utensils and 
degree of soiling. 
Information for test institutes 
Test institutes can request the conditions  
for running comparison tests by sending 
an e-mail to  
[email protected]. 
Quote the appliance number (E
­Nr.) 
and the production date (FD) which you  
can find on the rating  
plate  1j on the appliance door. * depending on model 
Additional options can be set with the  
buttons 
@....

en13
Aqua sensorAqua sensor *
* depending on model 
The Aqua sensor is an optical measuring  
device (light barrier) which measures the  
turbidity of the rinsing water. 
The Aqua sensor is used according to the  
programme. If the Aqua sensor is active, 
“clean” rinsing water can be transferred to  
the next rinse bath and water consumption  
can be reduced by 2–4 litres. If the 
turbidity is greater, the water is drained  
and is replaced with fresh water. In the  
automatic programmes the temperature...

en 
14
To change the setting: 
– Press programme button 
3.
Each time the button is pressed, the  
set value increases by one level; when  
the value of  ˜:‹ƒ  has been reached, 
the display jumps back to  ˜:‹‹  (off).
– Press START button  H. 
The set value is saved. 
Switching off the appliance 
Short time after the end of the programme: 
– Switch off ON/OFF switch  (.
– Turn off the tap (not applicable if Aqua- Stop fitted).
– Open the door.
– Remove the utensils when they have  cooled down.
m...

en15
A regular inspection and maintenance of  
your machine will help to prevent faults. 
This saves time and prevents problems. 
Overall condition of the machine 
– Check spray arm for grease and 
limescale deposits.
If you find such deposits: 
– Fill detergent dispenser with detergent.  Start the appliance without utensils in  
the programme with the highest rinsing 
temperature.
Clean the appliance with detergents/
appliance cleaners which are particularly  
suitable for use with dishwashers. 
–...

en 
16
Spray arms 
Limescale and contaminants in the rinsing  
water may block nozzles and bearings on 
the spray arms 
1* and  12.
– Check outlet nozzles on the spray arms  for blockages.
– Unscrew the upper spray arm  1*.
– Remove the lower spray arm  12 
upwards.
– Clean spray arms under running water. 
– Re-engage or screw on spray arms. The majority of   faults which could occur in  
daily operation can be rectified by the 
user. This ensures that the appliance is 
quickly available for use again....

en17
Waste water pump 
Large food remnants in the rinsing water  
not retained by the filters may block the 
waste water pump. The rinsing water is  
then not pumped out and covers the filter.  
In this case: 
– First disconnect the appliance from the 
power supply.
– Remove the filters  1:.
– Scoop out water, use a sponge if  required.
– Loosen screws on the pump cover  (Torx T 20) and pull off.
– Check inner compartment and remove  any foreign objects.
– Place pump cover in the original  position,...

en 
18– Clean filter in the supply hose.  
– Reconnect power supply.  
– Turn on the tap.
– Switch on the appliance.
– Water is left in the appliance  
at the end of the programme. 
–(“ :ƒ… ) Waste water hose 
is blocked or kinked. 
Filters blocked.
– (“ :ƒ† ) Waste water pump blocked, 
cover on the waste water pump  
is not locked in position  
(see Waste water pump).
– Filters blocked.
– The programme has not yet ended.  Wait until programme ends (digital  
display indicates  ‹:‹‹ ) or 
implement the...

en19
If the advice given does not resolve your  
problem, please contact your customer 
service. Contact details can be found on 
the back cover of this instruction manual  
or in the enclosed customer service list.  
When calling , please quote the appliance 
number (1) and the production date  
(FD = 2) which can be found on the rating  
plate 
1j on the appliance door.
Rely on the expertise of the 
manufacturer.   Call us to ensure that the 
repair will be carried out  by fully-trained 
service...

en 
20
– Some models:
The plastic housing on the water  
connection contains an electric valve,  
the connecting cables are in  the supply 
hose. Do not cut through this hose,  
do not immerse the plastic housing in  
water.
Delivery 
Your dishwasher has been checked  
thoroughly in the factory to ensure that it is  
in working order. This may cause small 
water stains. These will disappear after the 
first wash cycle. 
Technical specifications 
Weight: 
max. 27 kg 
Voltage: 
220–240 V, 50 Hz or 60 Hz...