Siemens Sc 76m530 Operating Instructions
Have a look at the manual Siemens Sc 76m530 Operating Instructions online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 428 Siemens manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
en11 The max. possible number of programmes is illustrated in this overview. The corresponding programmes for your appliance can be fo und on the fascia. The programme data has been measured in the laboratory acc ording to AS/NSZ 2007. Overview of programmes Programme Type of utensils and soiling Programme sequencePossible additional optionsProgramme data 1.) Duration: hs/ mins 2.) Energy consumption in kWh 3.) Water consumption in litres 4.) With Aquasensor ª Pots and Pans 70° Pots, utensils and cutlery Highly soiled Prerinse Clean 70° Intermediate rinse Final rinse 70° DryAll 1.) 2:20 2.) 1,20 3.) 10 4.) 8 ± / ° Intensive 65° Pots, utensils and cutlery Highly soiled Prerinse Clean 65° Intermediate rinse Final rinse 70° DryAll 1.) 2:40 2.) 1,15 3.) 9 4.) 9 ¹ Auto 45° – 65° Utensils and cutlery Normally soiled Is optimised according to the soiling with the aid of sensors.All 1.) 1:40 - 2:50 2.) 0,6 - 1,15 3.) 6 - 11 4.) 6 - 11 Ù / Ø Normal 45° Utensils and cutlery Normally soiled Prerinse Clean 45° Intermediate rinse Final rinse 45° DryAll 1.) 2:40 2.) 0,49 3.) 10,1 4.) - ñ / ð Quick 45° Utensils and cutlery Lightly soiled Clean 45° Intermediate rinse Final rinse 55°Extra drying 1.) 0:35 2.) 0,50 3.) 6 4.) - ù / ø Prerinse Lightly soiled Prerinse None 1.) 0:15 2.) 0,05 3.) 3 4.) -
en 12 Programme selection You can select a suitable programme according to the type of utensils and degree of soiling. Information for test institutes Test institutes can request the conditions for running comparison tests by sending an e-mail to [email protected]. Quote the appliance number (E Nr.) and the production date (FD) which you can find on the rating plate 1j on the appliance door. * depending on model Additional options can be set with the buttons @. Express Wash/ Speed PerfectŸ Express Wash/ Speed Perfect * The >>Express Wash/ Speed Perfect
en13 Aqua sensorAqua sensor * * depending on model The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water. The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 2–4 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling. Switching on the appliance – Turn on the tap fully. – Switch on ON/OFF switch (. The display of the last selected programme flashes. This programme remains selected if no other programme button 0 is pressed. The expected programme duration flashes on the digital display `. – Press the START button H. The programme starts running. Remaining running time display When the programme is selected, the remaining running time of the programme is indicated on the digital display `. The running time is determined during the programme by the water temperature, the number of utensils as well as the degree of soiling and may vary (depending on the selected programme). Timer programmingTimer programming * * depending on model You can delay the start of the programme in 1-hour steps up to 24 hours. – Close the door. – Switch on ON/OFF switch (. – Press button 8 + until the digital display ` jumps to œ:‹‚ . – Press 8 + or – button until the displayed time corresponds with your requirements. – Press START button H, timer programming is activated. – To delete timer programming, press the 8 + or – button until ` œ :‹‹ is indicated on the digital display. You can change your programme selection at any time until the programme starts. End of programme The programme has ended when the value ‹:‹‹ is indicated on the numerical display `. Switching off automatically after the end of the programmeSwitching off automatically after the end of the programme * * depending on model To save energy, the dishwasher is switched off 1 minute after the programme ends (factory setting). Automatic disconnection can be adjusted from ˜:‹‹ to ˜:‹ƒ . – Close the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button H until š:‹ ... is indicated on the digital display. – Release both buttons. – Press programme button # until the factory set value ˜:‹‚ is indicated on the digital display `. Washing the dishes ˜:‹‹ Appliance does not switch off automatically ˜ :‹‚ Off after 1 min ˜ :‹ƒ Off after 120 min
en 14 To change the setting: – Press programme button 3. Each time the button is pressed, the set value increases by one level; when the value of ˜:‹ƒ has been reached, the display jumps back to ˜:‹‹ (off). – Press START button H. The set value is saved. Switching off the appliance Short time after the end of the programme: – Switch off ON/OFF switch (. – Turn off the tap (not applicable if Aqua- Stop fitted). – Open the door. – Remove the utensils when they have cooled down. m Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher. Any escaping water vapour could damage sensitive worktops. Interrupting the programme – Switch off ON/OFF switch (. The LEDs go out. The programme is saved. If the door was opened on an appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to spring open or water to run out of the appliance. – To continue the programme, switch on the ON/OFF switch ( again. Terminating the programmeTerminating the programme (Reset) – Press START button H for approx. 3 sec. The numerical display ` indicates ‹:‹‚ . – The programme sequence lasts approx. 1 min. On the digital display ` is indicated ‹:‹‹ . – Switch off ON/OFF switch (. Changing the programme When the START button H has been pressed, the programme cannot be changed. The only way a programme can be changed is by Cancel programme (Reset). Intensive drying The final rinse uses a higher temperature which improves the drying result. The running time may increase slightly. (Caution if utensils are delicate!) – Close the door. – Switch on ON/OFF switch (. – Hold down programme button # and press START button H until the digital display ` š :‹ ... is indicated. – Release both buttons. To change the setting: – Press the button 3 to switch the Intensive drying on š:‹‚ or off š:‹‹ . – Press START button H. The set value is saved.
en15 A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems. Overall condition of the machine – Check spray arm for grease and limescale deposits. If you find such deposits: – Fill detergent dispenser with detergent. Start the appliance without utensils in the programme with the highest rinsing temperature. Clean the appliance with detergents/ appliance cleaners which are particularly suitable for use with dishwashers. – Regularly clean door seal with a damp cloth. Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage. Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces. Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time. m Warning Never use other chlorinated household detergents! Health hazard! Rinse aid – Check the refill indicator X. If required, refill rinse aid. Filters The filters 1: keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters. The filter system consists of a coarse filter, a flat fine filter and a microfilter. – After each washing cycle check the filters for residue. – Unscrew filter cylinder as illustrated and take out filter system. – Remove any residue and clean filters under running water. – Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system. Maintenance and care
en 16 Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 1* and 12. – Check outlet nozzles on the spray arms for blockages. – Unscrew the upper spray arm 1*. – Remove the lower spray arm 12 upwards. – Clean spray arms under running water. – Re-engage or screw on spray arms. The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The following overview will help you locating the causes and gives helpful advise to eliminate them. Note If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset). (See chapter entitled “Dishwashing”) m Warning If on the digital display ` an error code ( “ :‹‚ to “:„‹ ), always disconnect the appliance from the power supply and then turn off the tap. You can rectify certain faults yourself (see following fault description), for all other faults please contact customer service and state the indicated fault “:XX. m Warning Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at considerable risk. Troubleshooting
en17 Waste water pump Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case: – First disconnect the appliance from the power supply. – Remove the filters 1:. – Scoop out water, use a sponge if required. – Loosen screws on the pump cover (Torx T 20) and pull off. – Check inner compartment and remove any foreign objects. – Place pump cover in the original position, press down and screw tight. – Install filters. ... when the appliance is switched on The appliance does not start. – The mains fuse has tripped. – The appliance plug has not been inserted. – The appliance door has not been shut properly. ... changing settings A setting cannot be changed, a programme starts. – Wrong programme button pressed. Terminate the programme (see chapter entitled “Terminating the programme (Reset)”) and start all over again. – You did not wait until programme ended. ... on the appliance Lower spray arm rotates sluggishly. – Spray arm blocked. The door is difficult to open. * – Child-proof lock is activated. The deactivation instructions are at the back in the envelope. * depending on model Cover on the detergent dispenser cannot be closed. – Detergent dispenser overfilled or mechanism blocked by sticky detergent residue. Detergent residue in the detergent dispenser. – Dispenser was damp when filled. “Check water supply” display P lights up. – Tap turned off. – Water supply interrupted. – Supply hose kinked. – Filter in the water supply blocked. – Switch off the appliance and pull out the mains plug. – Turn off the tap.
en 18– Clean filter in the supply hose. – Reconnect power supply. – Turn on the tap. – Switch on the appliance. – Water is left in the appliance at the end of the programme. –(“ :ƒ… ) Waste water hose is blocked or kinked. Filters blocked. – (“ :ƒ† ) Waste water pump blocked, cover on the waste water pump is not locked in position (see Waste water pump). – Filters blocked. – The programme has not yet ended. Wait until programme ends (digital display indicates ‹:‹‹ ) or implement the “Reset” function. Error code “:ƒƒ – Filters 1: are soiled or blocked. Refill indicator for rinse aid X is not lit. – Refill indicator switched off. – Adequate rinse aid available. ... during the wash cycle Unusual foam formation. – Handwash liquid in the rinse aid dispenser. Spilled rinse aid causes excessive frothing, therefore please remove with a cloth. Appliance stops during the wash cycle. – Power supply interrupted. – Water supply interrupted. Filling valves making striking noises – Caused by the installation of the water line and has no effect on the function of the machine. Remedial action is not possible. Knocking/rattling noise during rinsing – Spray arm is striking utensils. – Utensils not arranged correctly. ... on the utensils Food residue on the utensils. – Utensils placed too closely together, utensils basket overfilled. – Too little detergent. – Rinse programme too weak. – Spray arm rotation obstructed. – Spray arm nozzles blocked. – Filters blocked. – Filters incorrectly inserted. – Waste water pump blocked. Tea or lipstick residue is not completely removed. – The detergent has an inadequate bleaching effect. – Too low rinsing temperature. – Too little/unsuitable detergent. Dull, discoloured glasses, film cannot be washed off. – Unsuitable detergent. – Glasses not dishwasher-proof. Streaks on glasses and cutlery, glasses have metallic appearance. – Too much rinse aid. Plastic parts discoloured. – Too little/unsuitable detergent. – Too weak programme selected. Utensils not dry. – Appliance door opened too early and utensils taken out too early. – Programme selected without drying. – Too little rinse aid.
en19 If the advice given does not resolve your problem, please contact your customer service. Contact details can be found on the back cover of this instruction manual or in the enclosed customer service list. When calling , please quote the appliance number (1) and the production date (FD = 2) which can be found on the rating plate 1j on the appliance door. Rely on the expertise of the manufacturer. Call us to ensure that the repair will be carried out by fully-trained service engineers, who are equipped with original spare parts for your appliance. The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragraphs or in the installation instructions. Install the appliance in the correct sequence: – Checking appliance on delivery – Installing the appliance – Waste water connection – Fresh water connection – Electrical connection Safety instructions – Install and connect the appliance according to the installation and assembly instructions. – Prior to installation, disconnect the dishwasher from the power supply. – Ensure that the protective conductor system of the domestic supply has been correctly installed. – The electrical connection conditions must correspond with the specifications on the dishwasher rating plate 1j. – If the power cord of this appliance is damaged, it must be replaced with a particular power cord. To prevent injury, the power cord may be replaced by customer service only. – If the dishwasher is installed in a high- sided unit, the unit must be secured properly. – Do not install the appliance near heat sources (radiators, heat storage tanks or other appliances which generate much heat) and install it under a hob only in consideration of the stipulated safety clearances. – After installing the appliance, ensure that the plug is easily accessible. Customer service Installation
en 20 – Some models: The plastic housing on the water connection contains an electric valve, the connecting cables are in the supply hose. Do not cut through this hose, do not immerse the plastic housing in water. Delivery Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle. Technical specifications Weight: max. 27 kg Voltage: 220–240 V, 50 Hz or 60 Hz Connected load: 2.0–2.4 kW Fuse: 10/16 A Water pressure: at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead. Inlet rate: minimum 10 litres/minute Water temperature: for cold water connection only. Installation The required installation dimensions can be found in the installation instructions. Level the appliance. Ensure that the appliance is situated securely on the floor. – The appliance can easily be installed in a fitted kitchen between wooden and plastic walls. Waste-water connection – The required work sequence can be found in the installation instructions. If required, fit a siphon with an drainage connection. – Connect the waste-water hose to the drainage connection of the siphon with the enclosed parts. Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out! Fresh water connection – Connect the fresh-water connection to the tap according to the installation instructions with the enclosed parts. Ensure that the fresh-water connection is not kinked, crushed or twisted. – When replacing the appliance, always use a new water supply hose. Water pressure: at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water pressure: connect pressure-reducing valve ahead. Inlet rate: minimum 10 litres/minute Water temperature: for cold water connection only.