Sharp Xv Z90u Projector User Manual

E-10
Important
InformationPart Names
Inserting the batteries
13Pull down the tab on the
battery cover and
remove the cover
towards the direction of
the arrow.2Insert two AA size
batteries, making sure
the polarities match the

 and  marks inside
the battery compartment.Insert the lower tab of
the battery cover into
the opening, and press
the cover until it clicks
in place.
Top View
Remote Control
LIGHT button
16
24
35
36
19
1926
26
24
2424
14
24
32
15
POWER buttons (ON/OFF)
ENTER button
19KEYSTONE...

E-11
Important
Information
Supplied Accessories
Power cord
QACCDA007WJPZ Remote control
RRMCGA064WJSATwo AA size batteriesTerminal cover
GCOVAA116WJKA
Operation manual
TINS-A286WJZZ Lens cap
CCAPHA004WJ01
Lens cap strap
UBNDT0013CEZZScrews for terminal cover
XBBSN40P10000
XVZ90U(E)#p08_11.pm620/8/02, 7:19 pm 11 

E-12
Setup & Connections
Power Supply
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Connections
Power cord
CAUTION
• Make sure the power cord is firmly connected into the AC socket.
• The projector will enter the standby mode as you re-plug it into the AC socket, when unplugging the power cord after turning the power
off by pressing the POWER button. However, if the projetor was turned off by disconnecting the power cord or by a power failure,...

E-13
Setup & Connections
1
2 To S-video output terminal
2 To video output terminal 1
Projector
VCR, Laser disc player,
DVD player or DTV decoder
Connecting to Video Equipment
Connecting to a DVD Player and DTV Decoder
2To component output
terminals
1Component cable
(commercially available)DVD player
or
DTV decoder 1Connect each RCA connector of a component cable to the corresponding
RCA INPUT 1 terminals on the projector.
2Connect the other end of the cable to the corresponding terminals on a DVD
player...

E-14
Setup & Connections
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, cross
type, commercially available), the computer can be used to control the projector and check the status of the
projector. See pages 52 and 53 for details.
Connecting a computer with analog RGB output
1Connect the DVI end of the DVI to 15-pin D-sub adapter to the INPUT 2 port on the projector.
2Connect the D-sub end of the DVI to 15-pin D-sub adapter to the computer.
When...

E-15
Setup & Connections
Operating the Remote Control
The remote control can be used to control the projec-
tor within the range shown on the left.
• The signal from the remote control can be reflected off a
screen for easy operation. However, the effective distance
of the signal may differ due to the screen material.
Remote Control
Remote Control
45˚
23
 (7 m)
30˚30˚
45˚
30˚
Using the remote control in a dark
room
The backlights of the operation buttons can be turned
on for five seconds and off by...

E-16
Setup & Connections
Power ON/OFF
Press POWER ON.
•The blinking green LAMP REPLACEMENT indicator
shows that the lamp is warming up. Wait until the
indicator stops blinking before operating the projector.
•If the power is turned off and then immediately turned
on again, it may take a short while before the lamp
turns on.
•After the projector is unpacked and turned on for the first
time, a slight odor may be emitted from the exhaust
ventilative hole. This odor will soon disappear with use.
When the...

E-17
Setup & Connections
Using the Swivel Stand
Setting Up the Screen
You can adjust the angle and direction of the projected image by using
the Swivel Stand.
1Unlock the lever on the Swivel Stand.
2Adjust the angle and direction of the projected image as you want
by lifting up the projector and rotating the projector on the Swivel
Stand.
3Lock the lever on the Swivel Stand.
CAUTION
•Do not hold the lens when lifting, lowering or rotating the projector.
•When lowering the projector, be careful not to get...

E-18
Setup & Connections
DOWNUP
Lens shift dialUP
DOWN
The picture can be adjusted within the shift range of the lens by rotating the lens shift dial on the top of the
projector using your finger.
Using the Lens Shift
Projector
Projected Image
XVZ90U(E)#p15_21.p6520/8/02, 7:22 pm 18 

E-19
Setup & Connections
Keystone Correction
This function can be used to adjust the Keystone
settings.
•For detaiils about using the menu screen, see page 26.
Description of 2D Keystone Correction
Selected item Description
H Keystone Horizontally adjusts the keystone settings.
V Keystone Vertically adjusts the keystone settings.
Reset V and H Keystone adjustments are returned to the factory
preset settings.
Horizontal Keystone Correction
Vertical Keystone Correction
1Press KEYSTONE on the projector or...