Sharp Xv Z9000u Projector User Manual

E-11
Important
Information
Part Names
Inserting the batteries
13Pull down the tab on the
battery cover and
remove the cover
towards the direction of
the arrow.2Insert two AA size
batteries, making sure
the polarities match the

 and  marks inside
the battery compartment.Insert the lower tab of
the battery cover into
the opening, and press
the cover until it clicks
in place.
Top View
Remote Control
BACKLIGHT button
17
23
38
25
35
26
2626
26
23
2323
23
23
30
19
16
POWER buttons (ON/OFF)
ENTER button
UNDO...

E-12
Important
InformationSupplied Accessories
Power cord
CACCU5013DE01 Remote control
RRMCG1657CESATwo AA size batteriesTerminal cover
CCOVA1985CE01
Projector operation manual
TINS-7416CEZZ
SharpVision Manager operation manual
TINS-7418CEZZ
Lens cap
PCAPH1056CESACD-ROM
(SharpVision Manager)
UDSKA0047CEN1 

E-13
Setup & Connections
Power Supply
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Connections
Power cord
CACCU5013DE01
CAUTION
• Make sure the power cord is firmly connected into the AC socket.
• The projector will enter the stand-by mode after turning the power off and then re-plugging the power cord into the AC socket. However,
if you turned off the power by disconnecting the power cord or because of a power failure, the projector will...

E-14
Setup & Connections1
2 To S-video output ter minal
2 To video output ter minal 1
Projector
VCR,
Laser disc player,
DVD player or
DTV decoder
Connecting to Video Equipment
Connecting to a DVD Player and DTV Decoder
*
*
2To component output
terminals
1Component cable
(commercially available)DVD player
or
DTV decoder 1Connect each RCA connector of a component cable to the corresponding
RCA INPUT 1 or 2 ter minals on the projector.
2Connect the other end of the cable to the corresponding terminals on a...

E-15
Setup & Connections
Connecting to a Computer
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (null modem, cross
type, commercially available), the computer can be used to control the projector and check the status of the
projector. See pages 52, 53 and 54 for details.
Connecting to a computer using the INPUT 5 COMPUTER-RGB port
1Connect one end of the RGB cable (commercially available) to the INPUT 5 COMPUTER-RGB port on the
projector.
2Connect the other end...

E-16
Setup & Connections
Operating the Remote Control
The remote control can be used to control the projec-
tor within the range shown on the left.
• The signal from the remote control can be reflected off a
screen for easy operation. However, the effective distance
of the signal may differ due to the screen material.
Remote Control
Remote Control
45˚
23
 (7 m)
30˚30˚
45˚
30˚
Using the remote control in a dark
room
The backlights of the operation buttons can be turned
on for five seconds and off by...

E-17
Setup & Connections
Power ON/OFF
Press POWER ON.
•The flashing blue LAMP REPLACEMENT indicator
shows that the lamp is warming up. Wait until the
indicator stops flashing before operating the projector.
•If the power is turned off and then immediately turned
on again, it may take a short while before the lamp
turns on.
•After the projector is unpacked and turned on for the first
time, a slight odor may be emitted from the exhaust
ventilative hole. This odor will soon disappear with use.
When the...

E-18
Setup & Connections
Using the Adjustment Feet
Setting Up the Screen
You can adjust the height of the image by raising the projector with
the foot releases.
1Press the foot releases and lift the projector to the desired angle.
2Remove your hands from the foot releases. Once the adjustment
feet have locked in position, release the projector.
3If the screen is at an angle, the adjusters can be used to adjust
the angle of the image.
Returning the projector to its original position
While holding the...

E-19
Setup & Connections
Keystone Correction
This function can be used to adjust the Keystone
settings.
1Press KEYSTONE on the remote control.
2Press ENTER to display the test pattern.
3Press 
/// to make adjustments.
4a. Press KEYSTONE to return to the normal
screen.
b. To reset the Keystone setting, press UNDO.
•Straight lines and the edges of the displayed image may
appear jagged, when adjusting the Keystone setting.
3
4b2
1,4a 

E-20
Setup & Connections
Adjusting the Projection Distance
Position the projector perpendicular to the screen with all feet flat and leveled to achieve an optimal image.
Move the projector forward or backward if the edges of the image are distorted.
•The projector lens should be centered in the middle of the screen. If the lens center is not perpendicular to the screen, the
image will be distor ted, making viewing difficult.
•Position the screen so that it is not in direct sunlight or room light. Light...