Sharp Xv Z7000u Projector User Manual

E-31
Useful Features
Selecting the Picture Display Mode
Remote controlThis function allows you to modify or customize the
picture display mode to enhance the input image.
Depending on the input signal, you can choose the
picture display mode preferred.
1Press PICT MODE. Each time PICT MODE is
pressed, the picture mode changes as shown
below.
EXAMPLE
ON/OFF
POWERLAMP
TEMP.
KEYSTONE
INPUT
BACK ENTER MENUPICT MODERGB/
COMPONENT
INPUT 1PICT MODE
AUTO SYNC INPUT 2 GAMMA
KEYSTONEVIDEO FREEZE S-VIDEO CLR TEMP...

E-32
Useful Features
This function allows you to check the current input signal
information and the accumulated lamp usage time.
1Press MENU.
2Press ∂/ƒ to select “Options”, and then press
ENTER. The current input signal information and
the lamp usage time will be displayed.
•It is recommended that the lamp be replaced after
approximately 900 hours of usage. See pages 38 and 39
for lamp replacement.
Checking the Input Signal and the Lamp Usage Time
(GUI) On-screen Display
When no input signal is detected...

E-33
Useful Features
Selecting a Background Image
This function allows you to select the image displayed
when no signal is being sent to the projector.
Description of Background Images
1Press MENU.
2Press ∂/ƒ to select “Options”, and then press
ENTER.
3Press ∂/ƒ to select “Background”, and then
press ENTER.
4Press ∂/ƒ to select “Blue” or “None”.
5To exit from the GUI, press MENU.
*1 While projecting the blue screen, the picture automatically
switches to FULL (4:3) mode even if another display mode
has...

E-34
Useful Features
Reverse/Invert Image Function
This projector is equipped with a reverse/invert image
function which allows you to reverse or invert the pro-
jected image for various applications.
Description of Projected Images
Projector Remote control
(GUI) On-screen Display
Selected item
Front
CeilingFront
Rear
CeilingRearProjected image
Normal image
Inverted image
Reversed image
Reversed and inverted image
1Press MENU.
2Press ∂/ƒ  to select “PRJ Mode”, and then press
ENTER.
3Press ∂/ƒ to select...

E-35
Maintenance &
Troubleshooting
Air Filter Maintenance
Maintenance &
Troubleshooting
Air Filter Maintenance
Right Side View
Air filter
• This projector is equipped with an air filter to ensure the optimal
operating condition of the projector.
• The air filter should be cleaned every 100 hours of use. Clean the
filters more often when the projector is used in a dusty or smoky
location.
• Have your nearest Authorized SharpVision Service Center or Dealer
exchange the filter (PFILD0123CEZZ) when it is no...

E-36
Maintenance &
Troubleshooting
Air Filter Maintenance
13 2Remove the filter cover.
1Remove the air filter stopper.
2Remove the air filter.Turn over the projector. Press the
tab and remove the filter cover in
the direction of the arrow.
Remove the air filter.
Replacing the air filter
Ta b
Disconnect the power
cord.
Unplug the power cord from the
AC socket.
 


 

5Replace the filter cover.
Insert the tab on the end of the filter cover into the
filter cover opening and press the filter cover into...

E-37
Maintenance &
Troubleshooting
Lamp/Maintenance Indicators
Maintenance Indicators
POWERLAMP
TEMP.
ON/OFF
KEYSTONE
•The warning lights on the projector indicate problems
inside the projector.
•There are two warning lights: a TEMPERATURE
WARNING indicator which warns that the projector is too
hot, and a LAMP REPLACEMENT indicator which lets
you know when to change the lamp.
•If a problem occurs, either the TEMPERATURE WARNING
indicator or the LAMP REPLACEMENT indicator will
illuminate red. After...

E-38
Maintenance &
TroubleshootingVOL
POWER
MUTE
BACK
MENU
ENTER
ON/OFF
POWER
Replacing the Projection Lamp
•Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage or the inside of
the projector.
•To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
•Be sure to change the air filter during lamp replacement. The air filter comes packaged with the lamp unit.
46Remove the air filter.5Replace the air filter.
13Turn...

E-39
Maintenance &
Troubleshooting
Replacing the Projection Lamp
7Remove the lamp cage cover.
Turn over the projector and loosen the user service
screw that secures the lamp cage cover. Then lift
open the cover in the direction of the arrow.
910Insert the new lamp cage.Attach the lamp cage cover.
Slide the lamp cage cover in the direction of the
arrow. Then tighten the user service screw. Press the lamp cage firmly into the lamp cage
compartment. Fasten the securing screws.
8Remove the lamp cage.
Loosen...

E-40
Maintenance &
Troubleshooting
Using the Kensington Lock
This projector has a Kensington Security Standard
connector for use with a Kensington MicroSaver Security
System. Refer to the information that came with the
system for instructions on how to use it to secure the
projector.
Kensington Security
Standard connector
Check
•Projector power cord is not plugged into the wall outlet.
•The filter cover is not securely installed.
•Selected input is wrong. (See page 16.)
•Cables incorrectly connected to...