Sharp Xr 1x Projector User Manual

							57
Appendix
Remove the lamp unit.• Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow. At this time, keep the lamp
unithorizontal and do not tilt it.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Insert the new lamp unit.• Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
Replace the lamp unit cover.• Align the tab on the lamp unit cover
(1)and place it while pressing the tab
(2) to close it. Then tighten the user ser-
vice screw (3) to secure the lamp unit
cover.
4
5
6
Connect the power cord.• Plug the power cord into the AC socket
of the projector.
Reset the lamp timer.• While simultaneously holding down
UMENU,TENTER and Y on the pro-
jector, press and SON/STANDBY on the
projector.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset. • Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
1
2
Info
AC socket Securing screwsHandle
User service
screw (for
lamp unit
cover)
ON/STANDBY button
ENTER button
MENU button Y button
• If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
Info 
						

							58
Connecting Pin Assignments
RGB Input INPUT 1 RGB Signal Terminal: 15-pin Mini D-sub female connector
1. Video input (red)
2. Video input (green/sync on green)
3. Video input (blue)
4. Not connected
5. Not connected
6. Earth (red)
7. Earth (green/sync on green)
8. Earth (blue)
9. Not connected
10. GND
11. Not connected
12. Bi-directional data
13. Horizontal sync signal: TTL level
14. Vertical sync signal: TTL level
15. Data clock
USB Terminal: 4-pin B-type USB female connectorComponent Input
510 15
1
11
6
34 12
1. PR (CR)
2. Y
3. P
B (CB)
4. Not connected
5. Not connected
6. Earth (P
R)
7. Earth (Y)
8. Earth (P
B)
9. Not connected
10. Not connected
11. Not connected
12. Not connected
13. Not connected
14. Not connected
15. Not connected
1. SG
2. USB+
3. VCC
4. USB–Signal
GND
USB data+
USB power
USB data– Signal name 
						

							59
Appendix
DTV
• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this
occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to
change display modes can be found in your notebook computer’s operation manual.
• When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.
Computer
Computer Compatibility Chart
• Multiple signal support
Horizontal Frequency: 15-70 kHz,
Vertical Frequency: 45-85 Hz,
Pixel Clock: 12-108 MHz
Sync signal:Compatible with TTL level
• Compatible with sync on green signal
The following is a list of modes that conform to VESA. However, this projector supports other
signals that are not VESA standards.
27.0
31.5
37.5
27.0
31.5
37.9
27.0
31.5
27.0
31.5
37.9
26.2
31.5
34.7
37.9
37.5
43.3
31.4
35.1
37.9
46.6
48.1
46.9
53.7
40.3
48.4
56.5
60.0
68.7
55.0
66.2
67.5
64.0
64.0
34.9
37.8
49.7
60.2
68.760
70
85
60
70
85
60
70
60
70
85
50
60
70
72
75
85
50
56
60
70
72
75
85
50
60
70
75
85
60
70
75
60
60
67
60
75
75
75 640× 350
640× 400
720× 350
720× 400
640× 480
800× 600
1,024× 768
1,152× 864
1,280× 1,024
1,400× 1,050
640× 480
800× 600
832× 624
1,024× 768
1,152× 870 MAC 13"
MAC 16"
PC
VGA
SVGA
XGA
SXGA
SXGA+
VGA
XGA
SXGA
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
XR-1X XR-1S PC/MAC
MAC 19"
MAC 21"SVGA
Signal
480I
480P
540P
576I
576P
720P
1035I
1035I
1080I
1080IHorizontal Frequency (kHz)
15.7
31.5
33.8
15.6
31.3
45.0
28.1
33.8
28.1
33.8Vertical Frequency (Hz)
60
60
60
50
50
60
50
60
50
60
Note
• Compatible with the signals below in
intelligent compression
XR-1X: SXGA, SXGA+
XR-1S: XGA, SXGA, SXGA+
• Intelligent Compression and Expansion
System resizing technology
ResolutionHorizontal Frequency
(kHz)Vertical Frequency
(Hz)VESA StandardDisplay
Upscale
Tr u e
Intelligent
Compression
Upscale
Intelligent CompressionTr u eUpscale
Tr u e
Intelligent
Compression
Intelligent
CompressionUpscale
Tr u e 
						

							60
Troubleshooting
No picture and no sound
or projector does not
start.
Sound is heard but no
picture appears (or picture
is dark).
Color is faded or poor.
Picture is blurred;
noise appears.
Picture appears but no
sound is heard.
An unusual sound is
occasionally heard from
the cabinet.
Maintenance indicator on
the projector illuminates
or blinks in red.Problem Check
• Projector power cord is not plugged into the wall outlet.
• Power to the external connected devices is off.
• The selected input mode is wrong.
• Cables incorrectly connected to the projector.
• Remote control battery has run out.
• External output has not been set when connecting notebook
computer.
• The lamp unit cover is not installed correctly.
• Cables incorrectly connected to the projector.
• “Bright” is set to minimum position.
• Image adjustments are incorrectly set.
(Video Input only)
• Video input system is incorrectly set.
• Adjust the focus.
• The projection distance exceeds the focus range.
(Computer Input only)
• Perform “Fine Sync” Adjustments (“Clock” Adjustment)
• Perform “Fine Sync” Adjustments (“Phase” Adjustment)
• Noise may appear depending on the computer.
• Cables incorrectly connected to the projector.
• Volume is set to minimum.
• If the picture is normal, the sound is due to cabinet shrinkage
caused by room temperature changes. This will not affect operation
or performance.
• See “Maintenance Indicators”.
Page
25
–
29
23,24,25
14,15
23
56,57
23,24,25
40
40
51
27
19
51
51
–
23,24,25
29
–
54 
						

							61
Appendix
Problem
Picture is green on
INPUT 1 COMPONENT.
Picture is pink (no green)
on INPUT 1 RGB.
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection
The image sometimes
flickers.
The lamp needs much
time to turn on.
Picture is dark.Check
• Change the input signal type setting.
• Image adjustments are incorrectly set.
• When temperature inside the projector increases, the cooling fan
runs faster.
• The lamp indicator is illuminating in red.
Replace the lamp.
• Cables incorrectly connected to the projector or the connected
equipment works improperly.
• If this happens frequently, replace the lamp.
• The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.Page
51
40
–
53
23,24,
25,51,56
56
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 30 seconds. 
						

							62
For SHARP Assistance
If you encounter any problems during setup or operation of this projector, first
refer to the “Troubleshooting” section on pages 60 and 61. If this operation manual
does not answer your question, please contact the SHARP Service departments
listed below.
U.S.A. Sharp Electronics Corporation
1-888-GO-SHARP (1-888-467-4277)
[email protected]
http://www.sharplcd.com
Canada Sharp Electronics of Canada Ltd.
(905) 568-7140
http://www.sharp.ca
Mexico Sharp Electronics Corporation
Mexico Branch
(525) 716-9000
http://www.sharp.com.mx
Latin America Sharp Electronics Corp. Latin
American Group
(305) 264-2277
[email protected]
http://www.siempresharp.com
Germany Sharp Electronics (Europe) GMBH
01805-234675
http://www.sharp.de
U.K. Sharp Electronics (U.K.) Ltd.
0161-205-2333
[email protected]
http://www.sharp.co.uk
Italy Sharp Electronics (Italy) S.P.A.
(39) 02-89595-1
http://www.sharp.it
France Sharp Electronics France
01 49 90 35 40
[email protected]
http://www.sharp.fr
Spain Sharp Electronica Espana, S.A.
93 5819700
[email protected]
http://www.sharp.es
Switzerland Sharp Electronics (Schweiz) AG
0041 1 846 63 11
[email protected]
http://www.sharp.ch
Sweden Sharp Electronics ( Nordic ) AB
(46) 8 6343600
[email protected]
http://www.sharp.se
Austria Sharp Electronics (Europe) GMBH
Branch Office Austria
0043 1 727 19 123
[email protected]
http://www.sharp.atBenelux SHARP Electronics Benelux BV
0900-SHARPCE (0900-7427723)
Nederland
9900-0159 Belgium
http://www.sharp.nl
http://www.sharp.be
http://www.sharp.lu
Australia Sharp Corporation of Australia Pty.
Ltd.
1300-135-022
http://www.sharp.net.au
New Zealand Sharp Corporation of New Zealand
(09) 634-2059, (09) 636-6972
http://www.sharpnz.co.nz
Singapore Sharp-Roxy Sales (S) Pte. Ltd.
65-226-6556
[email protected]
http://www.sharp.com.sg
Hong Kong Sharp-Roxy (HK) Ltd.
(852) 2410-2623
[email protected]
http://www.sharp.com.hk
Taiwan Sharp Corporation (Taiwan)
0800-025111
http://www.sharp-scot.com.tw
Malaysia Sharp-Roxy Sales & Service Co.
(60) 3-5125678
U.A.E.Sharp Middle East Fze
971-4-81-5311
[email protected]
Thailand Sharp Thebnakorn Co. Ltd.
02-236-0170
[email protected]
http://www.sharp-th.com
Korea Sharp Electronics Incorporated of
Korea
(82) 2-3660-2002
[email protected]
http://www.sharpkorea.co.kr
India Sharp Business Systems (India)
Limited
(91) 11- 6431313
[email protected] 
						

							63
Appendix
Specifications
Projector
XR-1X / XR-1S
NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480I/DTV480P/
DTV540P/DTV576I/DTV576P/DTV720P/DTV1035I/DTV1080I/DTV1080I-50
Single Chip Digital Micromirror Device
TM (DMDTM) by Texas InstrumentsPanel size: [XR-1X] 0.7" (17.5 mm) (10.5 [H] × 14.0 [W] mm), 1 chip XGA DMD
[XR-1S] 0.55" (13.7 mm) (8.2 [H] × 10.9 [W] mm), 1 chip SVGA DMD
No. of dots: [XR-1X] 786,432 dots (1,024 [H] × 768 [V])
[XR-1S] 480,000 dots (800 [H] × 600 [V])
[XR-1X] 1–1.16 × zoom lens, F2.80–3.10, f = 25.8–30.0 mm
[XR-1S] 1–1.16 × zoom lens, F2.60–2.84, f = 19.3–22.6 mm
150 W DC lamp
15-pin mini D-sub connector
Y: 1.0 Vp-p, sync negative, 75 Ω terminated
P
B: 0.7 Vp-p, 75 Ω terminated
PR: 0.7 Vp-p, 75 Ω terminated
[XR-1X] 700 TV lines (DTV720P)
[XR-1S] 520 TV lines (DTV720P)
15-pin mini D-sub connector
RGB separate/sync on green type analog input: 0–0.7 Vp-p, positive, 75 Ω terminatedHORIZONTAL SYNC. SIGNAL: TTL level (positive/negative)
VERTICAL SYNC. SIGNAL: Same as above
4-pin mini DIN connector
Y (luminance signal): 1.0 Vp-p, sync negative, 75 Ω terminated
C (chrominance signal): Burst 0.286 Vp-p, 75 Ω terminated
RCA connector: VIDEO, composite video, 1.0 Vp-p, sync negative, 75 Ω
terminated
12–108 MHz
45–85 Hz
15–70 kHz
ø3.5 mm minijack: AUDIO, 0.5 Vrms, more than 22 kΩ (stereo)
2.8 cm round × 1
AC 100–240 V
2.0 A
50/60 Hz
195 W (Standard mode)/177 W (Eco/Quiet mode “On”) with AC 100 V
190 W (Standard mode)/167 W (Eco/Quiet mode “On”) with AC 240 V
4 W (AC 100 V) – 5 W (AC 240 V)
730 BTU/hour (Standard mode)/660 BTU/hour (Eco/Quiet mode “On”) with AC 100 V
710 BTU/hour (Standard mode)/630 BTU/hour (Eco/Quiet mode “On”) with AC 240 V
41°F to 95°F (+5°C to +35°C)
–4°F to 140°F (–20°C to +60°C)
Plastic
38 kHz
9
47/64"× 2 17/32"× 4 13/16" (247 (W) × 64 (H) × 122 (D) mm) (main body only)
947/64"× 2 23/32"× 4 13/16" (247 (W) × 69 (H) × 122 (D) mm) (including adjustment
foot and projecting parts)
3.20 lbs. (1.45 kg)
Remote control, Lithium battery, Power cord for U.S., Canada etc. (6', 1.8 m),
Power cord for Europe, except U.K. (6', 1.8 m), Power cord for U.K., Hong Kong
and Singapore (6', 1.8 m), Power cord for Australia, New Zealand and Oceania
(6', 1.8 m), RGB/USB cable (6', 1.8 m), Cable tie × 2, Soft case, Projector
manual CD-ROM, Operation manual
Lamp unit (Lamp/cage module) (AN-XR1LP), Remote control
(RRMCGA256WJSA), Lithium battery, Power cord for U.S., Canada etc.
(QACCDA029WJPZ), Power cord for Europe, except U.K. (QACCVA006WJPZ),
Power cord for U.K., Hong Kong and Singapore (QACCBA015WJPZ), Power
cord for Australia, New Zealand and Oceania (QACCLA024WJPZ), RGB/USB
cable (QCNWGA047WJPZ), Cable tie (UBNDTA015WJZZ), Soft case
(GCASNA011WJZZ), Projector manual CD-ROM (UDSKAA045WJN1), Opera-
tion manual (TINS-B148WJN1)
Product type
Model
Video system
Display method
DMD panel
Lens
Projection lamp
Component input signal
(INPUT1)
Horizontal resolution
Computer RGB input
signal (INPUT 1)
S-video input signal
(INPUT 2)
Video input signal
(INPUT 3)
Pixel clock
Vertical frequency
Horizontal frequency
Audio input signal
Speaker system
Rated voltage
Input current
Rated frequency
Power consumption
Power consumption (standby)Heat dissipation
Operating temperature
Storage temperature
Cabinet
I/R carrier frequency
Dimensions (approx.)
Weight (approx.)
Supplied accessories
Replacement parts
As a part of policy of continuous improvement, SHARP reserves the right to make
design and specification changes for product improvement without prior notice.
The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units. 
						

							64
Dimensions
Units: inches (mm)
413/16(122)
947/64(247)
447/64(120)
89/32(210)47/64(18.5)
41/2(114.3)
217/32(64)
27/32(56)
75/64(179.5)243/64(67.5)
115/16(49)611/32(161)
15/16(33)
127/64(36)
19/32(15)
359/64(99.3)
217/32(64)
27/32(56)
75/64(179.5)243/64(67.5)
115/16(49)611/32(161)
119/32(40.3)1
9/64(28.7)
XR-1X
XR-1S 
						

							65
Appendix
AC socket .................................................. 25
Accessories .............................................. 11
Adjustment buttons ................................... 36
Adjust vertical noise ........................... 35, 51
Aspect ratio ............................................... 30
AUDIO INPUT terminal ................. 23, 24, 25
Auto Keystone Correction ........................ 44
Auto Power Off ......................................... 48
Auto Search .............................................. 47
Auto Sync
(Auto Sync adjustment) .............. 32, 35, 51
AUTO SYNC button .................................. 32
AV MUTE button ....................................... 29
Background ............................................... 45
Blue ........................................................... 40
BORDER ............................................. 30, 31
Bright ......................................................... 40
Bright Boost .............................................. 41
Clock ......................................................... 51
CLR Temp (Color Temperature) ............... 41
Color ......................................................... 40
Contrast .................................................... 40
Eco/Quiet Mode ........................................ 47
ENTER button ........................................... 36
Exhaust vent ............................................. 13
Fine Sync .................................................. 51
Focus ring ................................................. 27
FREEZE button ........................................ 32
Front adjustment foot ............................... 28
Guide LEDs .............................................. 48
H-Pos .................................................. 35, 51
HEIGHT ADJUST button .......................... 28
Help ........................................................... 51
Image shift ................................................ 43
INPUT 1 terminal ................................ 23, 24
INPUT 1 – 3 modes .................................. 29
INPUT 2 terminal ...................................... 24
INPUT 3 terminal ...................................... 25
INPUT button ............................................ 29
Intake vent .......................................... 13, 52
Kensington Security
Standard connector ................................ 13
Keycode .................................................... 49
Keystone Correction ................................. 44
L CLICK/ENTER button ............................ 33
Lamp ......................................................... 55
Lamp indicator .......................................... 53
Index
Lamp Timer (Life) ..................................... 50
Lamp unit .................................................. 56
Language
(on-screen display language) ................. 46
Lithium Battery .................................... 14, 15
MENU/HELP button ............................ 36, 51
MOUSE/Adjustment buttons .................... 33
Mouse function ......................................... 33
NORMAL ............................................. 30, 31
ON/STANDBY button ............................... 26
Optional accessories ................................ 11
OSD Display ............................................. 44
PDF ........................................................... 10
Phase ........................................................ 51
Picture Adjustment .................................... 40
Picture Mode ............................................. 40
Power cord ................................................ 25
PRJ - ADJ ................................................. 47
PRJ Mode ................................................. 46
Progressive ............................................... 42
R CLICK/RETURN button ........................ 33
Rear adjustment foot ................................ 28
Red ........................................................... 40
Remote control ......................................... 14
Remote control sensor ............................. 15
Replacing the lamp ................................... 55
Resize ....................................................... 43
RESIZE button .......................................... 30
RETURN button ........................................ 37
RGB/USB cable ........................................ 23
SCR - ADJ ................................................ 43
Screen Size and Projection Distance (XR-1S) ...20Screen Size and Projection Distance (XR-1X) ...19
Setup Guide .............................................. 27
Sharp ........................................................ 40
Soft case ................................................... 11
sRGB ........................................................ 42
STRETCH ........................................... 30, 31
Supplied accessories ............................... 11
System Lock ............................................. 49
Temperature warning indicator ................. 53
Tint ............................................................ 40
USB terminal ............................................. 23
Video System ............................................ 35
Volume buttons ......................................... 29
V-Pos .................................................. 35, 51
Zoom knob ................................................ 28 
						

							SHARP CORPORATION