Sharp Xr 1x Projector User Manual

							Introduction Quick Start
SetupConnectionsBasic
OperationUseful
Features
Appendix
MULTIMEDIA PROJECTOR
MODEL
XR-1X
XR-1S
OPERATION MANUAL
(The picture shown above is of the XR-1S.) 
						

							IMPORTANT
For your assistance in reporting the loss or
theft of your Projector, please record the
Model and Serial Number located on the
bottom of the projector and retain this
information. Before recycling the packag-
ing, please be sure that you have checked
the contents of the carton thoroughly
against the list of “Supplied accessories”
on page 11.Model No.:
Serial No.:
SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-
ing a 5A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362
fuse marked 
 or  and of the same rating as above, which is also indicated on the pin
face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fit an appropriate type.
DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-
ately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 5A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:
WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows:
•The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol 
 or coloured green or
green-and-yellow.
•The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.
•The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.
IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN. 
						

							The supplied CD-ROM contains operation instructions in English, German, French,
Swedish, Spanish, Italian, Dutch, Portuguese, Chinese (Traditional Chinese and Simpli-
fied Chinese) and Korean. Carefully read through the operation instructions before
operating the projector.
Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,
Schwedisch, Spanisch, Italienisch, Niederländisch, Por tugiesisch, Chinesisch (Traditionelles
Chinesisch und einfaches Chinesisch) und Koreanisch. Bitte lesen Sie die
Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand,
français, suédois, espagnol, italien, néerlandais, portugais, chinois (chinois traditionnel et
chinois simplifié) et coréen. Veuillez lire attentivement ces instructions avant de faire
fonctionner le projecteur.
Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska,
franska, svenska, spanska, italienska, holländska, portugisiska, kinesiska (traditionell
kinesiska och förenklad kinesiska) och koreanska. Läs noga igenom bruksanvisningen
innan projektorn tas i bruk.
El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán,
francés, sueco, español, italiano, holandés, portugués, chino (chino tradicional y chino
simplificado) y coreano. Lea cuidadosamente las instrucciones de operación antes de
utilizar el proyector.
Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese,
svedese, spagnolo, italiano, olandese, portoghese, cinese (cinese tradizionale e cinese
semplificato) e coreano. Leggere attentamente le istruzioni per l’uso prima di usare il
proiettore.
De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Zweeds,
Spaans, Italiaans, Nederlands, Portugees, Chinees (Traditioneel Chinees en
Vereenvoudigd Chinees) en Koreaans. Lees de handleiding zorgvuldig door voor u de
projector in gebruik neemt.
O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês,
Sueco, Espanhol, Italiano, Holandês, Português, Chinês, (Chinês Tradicional e Chinês
Simplificado) e Coreano. Leia cuidadosamente todas as instruções de operação antes
de operar o projetor. 
						

							1
IntroductionBefore using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP
Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
WARNING:High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING:To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
WARNING:FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
IntroductionENGLISH
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the operation manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
See bottom of projector.
U.S.A. ONLY
U.S.A. ONLY
U.S.A. ONLY
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTIONRISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW. 
						

							2
WARNING:The cooling fan in this projector continues to run for about 90 seconds after the projector enters
standby mode. During normal operation, when putting the projector into standby mode always
use the ON/STANDBY button on the projector or on the remote control. Ensure the cooling fan has
stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING
THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 55.
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
AVERTISSEMENT A OBSERVER LORS
DU REMPLACEMENT DE LA LAMPE.
LAMP REPLACEMENT WARNINGBEFORE REMOVING THE SCREW, DISCONNECT POWER 
CORD. HOT SURFACE INSIDE. ALLOW 1 HOUR TO COOL 
BEFORE REPLACING THE LAMP. REPLACE WITH SAME 
SHARP LAMP UNIT MODEL AN-XR1LP ONLY.
UV RADIATION : CAN CAUSE EYE DAMAGE. TURN OFF
LAMP BEFORE SERVICING.
HIGH PRESSURE LAMP : RISK OF EXPLOSION. POTENTIAL
HAZARD OF GLASS PARTICLES IF LAMP HAS RUPTURED.
HANDLE WITH CARE. SEE OPERATION MANUAL.
DEBRANCHER LE CORDON D’ALIMENTATION AVANT DE 
RETIRER LES VIS. L’INTERIEUR DU BOITIER ETANT 
EXTREMEMENT CHAUD, ATTENDRE 1 HEURE AVANT DE 
PROCEDER AU REMPLACEMENT DE LA LAMPE. 
NE REMPLACER QUE PAR UNE LAMPE SHARP DE MODÈLE 
AN-XR1LP.
RAYONS ULTRAVIOLETS : PEUVENT ENDOMMAGER LES 
YEUX. ETEINDRE LA LAMPE AVANT DE PROCEDER
A L’ENTRETIEN.
LAMPE A HAUTE PRESSION : RISQUE D’EXPLOSION. 
DANGER POTENTIEL DE PARTICULES DE VERRE EN CAS 
D’ECLATEMENT DE LA LAMPE. A MANIPULER AVEC 
PRECAUTION, SE REPORTER AU MODE D’EMPLOI.
This SHARP projector uses a DMD panel. This very sophisticated panel contains 786,432 (XR-
1X) / 480,000(XR-1S)pixels micromirrors. As with any high technology electronic equipment
such as large screen TVs, video systems and video cameras, there are certain acceptable
tolerances that the equipment must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures. The enclosed computer cable must be used with the device. The cable is provided to
ensure that the device complies with FCC Class A verification.
U.S.A. ONLY
CAUTION ON LITHIUM BATTERY (for Remote Control unit)If a battery is reversed (positive end where the negative end belongs and vice versa), it can
overheat and rupture. This has happened when young children install batteries backwards.
Warn children 
not to take out batteries or install them. Parents should install the lithium
battery in the remote control. 
						

							3
Introduction
36
Using the Menu Screen
Menu Selections (Adjustments)
The menu can be operated to achieve two functions, adjustment and setting. (For setting the menu
items, see pages 38 and 39.)
Example: Adjusting “Bright”.
• This operation can also be performed by using the buttons on the projector.PressBMENU.• The “Picture” menu screen for the se-
lected input mode is displayed.
MOUSE Adjustment
button (P/R/O/Q)
Example: “Picture” screen menu for INPUT 1
(RGB) mode
PressQ or O to display the other
menu screen.
• The selected menu item is highlighted.
1
2
ENTER button
RETURN button
Menu item
Picture
Picture Mode
Contrast 0
0
0
0
K 7500SCR - ADJ PRJ - ADJ Help
BrightRedBlueCLR TempBright Boost
sRGBOff Standard
Off
Reset
SEL./ADJ. ENTER END
MENU/HELP
button
Operating with the projectorWhen “PRJ - ADJ” - “Guide LEDs” is set to “On”, the buttons used for menu adjustment on the
projector light up.
Example: When W,Y and the MENU/HELP button light up on the projector, you can use those
buttons for operation.
Adjustment buttons (W/Y/V/X)
MENU/HELP button
ENTER button
How to Read this Operation Manual
■The specifications of the XR-1X are slightly different from those of the XR-1S, however, you can
connect and operate both models in the same manner. This operation manual uses the XR-1S
for the purpose of explanation.
•In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from actual display.
Info........Indicates safeguards for using the projector.
For Future Reference
Buttons used in
this operation
On-screen
display
Button used in
this step
Note.........Indicates additional information for setting up and operating the
projector.
Index Maintenance Troubleshooting
P.  6 5 P.  5 2PP. 60 and 61 
						

							4
Contents
Preparing
Introduction
How to Read this Operation Manual .... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
How to Access the PDF Operation
Manuals ............................................ 10
Accessories ........................................ 11
Part Names and Functions ................. 12
Inserting the Lithium Battery................ 14
Usable Range...................................... 15
Quick Start
Quick Start .......................................... 16
Using
Basic Operation
Turning the Projector On/Off .............. 26Turning the Projector on....................... 26
Turning the Power off (Putting the
Projector into Standby Mode)........... 26
Image Projection ................................. 27About the Setup Guide........................ 27
Adjusting the Projected Image............ 27
Switching the Input Mode.................... 29
Adjusting the Volume........................... 29
Displaying the Black Screen and Turning
off the Sound Temporarily................. 29
Resize Mode......................................... 30
Useful Features
Adjusting/Operating with the
Remote Control ................................ 32
Auto Sync (Auto Sync Adjustment)..... 32
Freezing a Moving Image.................... 32
Selecting the Picture Mode.................. 32
Using Mouse Function......................... 33
Menu Items ......................................... 34
Using the Menu Screen ...................... 36
Menu Selections (Adjustments)........... 36
Menu Selections (Settings).................. 38
Setup
Setting up the Projector ...................... 18Setting up the Projector....................... 18
Standard Setup (Front Projection)....... 18
Projecting a Reversed Image.............. 18
Screen Size and Projection Distance
(XR-1X)............................................... 19
Screen Size and Projection Distance
(XR-1S)............................................... 20
Connections
Connections ........................................ 21
Samples of Cables for Connection .... 22
Connecting to a Computer ................. 23
Connecting to Video Equipment ......... 24
Connecting the Power Cord ............... 25
Picture Adjustment (“Picture” menu) .. 40Selecting the Picture mode.................. 40
Adjusting the Image............................. 40
Adjusting the Color Temperature......... 41
Emphasizing the Contrast.................... 41
Progressive........................................... 42
sRGB Setting........................................ 42
Adjusting the Projected Image
(“SCR - ADJ” menu)......................... 43
Setting the Resize Mode...................... 43
Adjusting the Image Position............... 43
Keystone Correction............................ 44
Setting On-screen Display................... 44
Selecting the Background Image........ 45
Setting the Setup Guide....................... 45
Reversing/Inverting Projected
Images............................................... 46
Selecting the On-screen Display
Language........................................... 46
Setting the Projector Function
(“PRJ - ADJ” menu).......................... 47
Eco/Quiet Mode................................... 47
Auto Search Function........................... 47
Auto Power Off Function...................... 48
Setting the Guide LEDs........................ 48
System Lock Function.......................... 49
Setting/Changing the keycode............ 49
Setting the Confirmation Sound........... 50
Checking the Lamp Life Status........... 50
Troubleshooting with “Help” menu ..... 51Displaying “Help” menu screen.......... 51 
						

							5
Introduction
Reference
Appendix
Maintenance ....................................... 52
Maintenance Indicators ...................... 53
Regarding the Lamp ........................... 55
Lamp..................................................... 55
Caution Concerning the Lamp............ 55
Replacing the Lamp............................. 55
Removing and Installing
the Lamp Unit.................................... 56
Resetting the Lamp Timer.................... 57
Connecting Pin Assignments ............. 58
Computer Compatibility Chart ............ 59
Troubleshooting.................................. 60
For SHARP Assistance ....................... 62
Specifications ..................................... 63
Dimensions ......................................... 64
Index ................................................... 65 
						

							6
1. Read InstructionsAll the safety and operating instructions should
be read before the product is operated.
2. Retain InstructionsThe safety and operating instructions should be
retained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be
followed.
5. CleaningUnplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. AttachmentsDo not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and MoistureDo not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a
swimming pool; and the like.
8. AccessoriesDo not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
9. TransportationA product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
IMPORTANT SAFEGUARDS
10. VentilationSlots and openings in the cabinet are provided
for ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
11. Power SourcesThis product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your product dealer
or local power company. For products intended
to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or PolarizationThis product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet,
please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
13. Power-Cord ProtectionPower-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
14. LightningFor added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system.
This will prevent damage to the product due to
lightning and power-line surges.
CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.