Sharp Xgmb50xl Manual

							29
Basic
Operation
3 Adjusting the Height
The height of the projector can be ad-
justed using the adjustment feet at the
front and rear of the projector.
When the screen is above the projec-
tor, the projection image can be made
higher by adjusting the projector.
1
2
3
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly while lifting or carry-
ing.
• Do not hold by the lens area.
Use the rear adjustment foot to
make the projector level.
• The projector is adjustable ±1 degree
from the standard position.
Remove your hands from the
HEIGHT ADJUST lever of the pro-
jector after its height has been
finely adjusted.
• The angle of projection is adjustable up
to 8 degrees from the surface on which
the projector is placed.
Lift the projector to adjust its
height while lifting the HEIGHT
ADJUST lever.HEIGHT
ADJUST lever
Info
Rear adjustment foot
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the pro-
cedures in Keystone Correction to correct the
distortion. (See pages 31 and 41.)
Note
Make small
adjustments.
XR-11XCL_EN_h06.9.1, 11:35 AM 29 
						

							30
Image Projection (Continued)
Displaying the Black Screen
and Turning off the Sound
Temporarily
Adjusting the Volume
Switching the Input Mode
PressCINPUT 1, CINPUT 2,
DINPUT 3 or EINPUT 4 on the remote
control to select the input mode.
• When pressing INPUT (P/R) on the projector,
input mode switches in the following order:
INPUT1 INPUT2 INPUT3 INPUT4.
• When “Auto Search” is set to “On”, INPUT (P/
R) on the projector functions as the Auto Search
buttons. (See page 43.)
Select the appropriate input mode for
the connected equipment.
Press K/L on the remote control or
–O/Q+ on the projector to adjust the vol-
ume.
• Pressing K/–O will lower the volume.
• Pressing L/Q+ will raise the volume.
• When the projector is connected to external
equipment, the volume level of the exter nal equip-
ment changes in accordance with the volume
level of the projector. Set the projector’s volume
to the lowest level when tur ning the projector on/
off or when changing the input signal.
• When you do not want to output the sound from
the projector’s speaker while the projector is con-
nected to external equipment, set “Speaker” in
“PRJ-ADJ” menu to “Off”. (See page 43.)
Press MAV MUTE on the remote con-
trol to temporarily display a black
screen and turn off the sound.
• Pressing MAV MUTE again will turn the projected
image back on.
Volume buttons
INPUT
buttons AV MUTE button
On-screen Display
Note
NoteOn-screen Display
XR-11XCL_EN_h06.9.1, 11:35 AM 30 
						

							31
Basic
Operation
0 KeystoneADJ. END
Correcting Trapezoidal
Distortion
When the image is projected either from
the top or from the bottom towards the
screen at an angle, the image becomes
distorted trapezoidally. The function for
correcting trapezoidal distortion is
called Keystone Correction.
• The Keystone Correction can be adjusted up
to an angle of approximately ±13 degrees and
the screen can also be set up to an angle of
approximately ±13 degrees (when the resize
mode is set to “NORMAL” (see page 32)).
Note
1
2
3
Press g KEYSTONE.• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use d KEYSTONE on the
projector.
Press P/Q or O/R to adjust the
Keystone Correction.
• You can also adjust the Keystone Cor-
rection using the adjustment buttons on
the projector.
Press g KEYSTONE to enter the
Keystone Correction mode.
• You can also display the on-screen dis-
play of the Keystone Correction mode
with d KEYSTONE on the projector.
• Press l RETURN while the on-screen dis-
play of the Keystone Correction mode is on
the screen to return to the default setting.
Note
KEYSTONE button
Adjustment buttons
(P/R/O/Q)
RETURN button
ROn-screen display
(Keystone Correction mode)
Shrinks upper side.
(Move the slide bar in the + direction.)
Shrinks lower side.
(Move the slide bar in the - direction.)
• While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
Info
When using PG-MB66X or PG-MB56X
• The projector automatically detects tilt and the
AUTO KEYSTONE feature automatically cor-
rects trapezoidal distortion.
•Automatic Keystone Correction may not work well in some
cases, such as when the screen is leaning, temperature is
extremely high or low, or zoom is at maximum or mini-
mum. In these cases, fine adjust the Keystone Correction
following steps 1 to 3.
•You can select “On” or “Off” for the Auto Keystone Correc-
tion mode. (See page 41.)
Note
XR-11XCL_EN_h06.9.1, 11:35 AM 31 
						

							32
Image Projection (Continued)
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image.
Press HRESIZE.• See page 41 for setting on menu screen.
Computer
RESIZE button
SVGA (800 K 600)
XGA (1024 K 768)
SXGA (1280 K 960)
SXGA L (1400 K 1050)SXGA (1280 K 1024)1280 K 720
1024 K 768 800 K 600
J J
768 K 576 600 K 450
J J
1024 K 576 800 K 450
PG-MB66X/MB56X/
XG-MB50X-L/
XR-11XC-L/10X-LXR-10S-LPG-MB66X/MB56X/
XG-MB50X-L/
XR-11XC-L/10X-LXR-10S-LPG-MB66X/MB56X/
XG-MB50X-L/
XR-11XC-L/10X-LXR-10S-L
1024 K 576 800 K 450 800 K 600 1024 K 768 600 K 450 768 K 576 1024 K 576 800 K 450
NORMALBORDER STRETCH
Other aspect ratios4:3 aspect ratio
: Cutout area on which images cannot be projected.
PG-MB66X/MB56X/
XG-MB50X-L/
XR-11XC-L/10X-LXR-10S-L
Input Signal
NORMALOutput screen image
Computer
Image type BORDER
STRETCH
SXGA
(1280K1024)Resolution
lower than
SVGA
SVGA
Resolution
higher than
SVGA
1280K720
4:3 aspect ratio
5:4 aspect ratio
16:9 aspect ratio
* Mode for projecting an image with the original
aspect ratio without cutting any portions. Resolution
lower than
XGA
XGA
Resolution
higher than
XGA
XR-11XCL_EN_h06.9.1, 11:35 AM 32 
						

							33
Basic
Operation
VIDEO
•“STRETCH” is fixed when 540P, 720P or 1080I signals are entered.
: Cutout area on which images cannot be projected.
: Area on which the image is not included in the original signals.Input Signal
DVD / Video Image typeOutput screen image
NORMAL
BORDERSTRETCH
480I, 480P, 576I,
576P, NTSC, PAL,
SECAM
540P, 720P, 1080I
4:3 aspect ratio
Letter box
Squeezed 16:9 image
Squeezed 4:3 image
16:9 aspect ratio
1
6:9 aspect ratio
(4:3 aspect ratio in 16:9)
* Mode for projecting an image with the original aspect ratio without cutting any portions.
XR-11XCL_EN_h06.9.1, 11:35 AM 33 
						

							34
Auto Sync
(Auto Sync Adjustment)
Operating with the Remote Control
Freezing a Moving Image
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page 46.)
Auto Sync function works when detect-
ing input signal after the projector turns
on.
Press FAUTO SYNC to manually ad-
just with Auto Sync function.
Press NFREEZE.
• The projected image is frozen.
Press NFREEZE again to return
to the moving image from the cur-
rently connected device.
1
2
Note
Selecting the Picture Mode
Press GPICTURE MODE.• When pressing GPICTURE MODE, the picture
mode changes in the following order:
Standard Presentation Movie Game sRGB
You can select the appropriate picture
mode for the projected image, such as
movie or video game.
• See page 39 for details on the picture mode.
Note
FREEZE button
AUTO SYNC
button
Adjustment buttons
(P/R/O/Q)
BREAK TIMER
button
PICTURE MODE
button
Displaying and Setting the
Break Timer
Press k BREAK TIMER.• The timer starts to count down from 5
minutes.1
2
Press P/R/O/Q to adjust the
length of the break time.
•Increases with P or Q
5 minutes s 6 minutes s 60 minutes•Shortens with O or R4 minutes s 3 minutes s1 minute
• The break time can be set in units of one
minute (up to 60 minutes).
ROn-screen display
Canceling the break time display function
Press k BREAK TIMER.
*
* “sRGB” is displayed only when RGB signal is
input.
• Break Timer does not function while the pro-
jector is operating the “Auto Sync”, “FREEZE”
or “AV MUTE” functions.
Note
XR-11XCL_EN_i06.9.1, 11:36 AM 34 
						

							35
Useful
Features
The following shows the items that can be set in the projector.
Menu Items
“Screen adjustment (SCR-ADJ)” menu
INPUT 1 (Component)/INPUT 2
(Component)/INPUT 3/INPUT 4 INPUT 1 (RGB)/INPUT2 (RGB)
“Picture” menu
Picture
Picture Mode
Contrast 0
0
0
0
K 7500SCR - ADJ PRJ - ADJ Help
BrightRedBlue
1CLR TempBright Boost
Lamp SettingStandard
Bright
Reset
SEL./ADJ. ENTER END
Picture
Picture Mode
Contrast 0
0
0
0
K 7500SCR - ADJ PRJ - ADJ Help
BrightColorTint0 Sharp
1CLR TempBright Boost
Progressive 3D ProgressiveStandard
Reset
SEL./ADJ. ENTER END
Lamp Setting Bright
Picture
Resize
Image Shift 0
0SCR - ADJPRJ - ADJ Help
KeystoneAuto Keystone
OSD Display
Background
Setup Guide
PRJ Mode
LanguageFront
English On Logo
On
Off Normal
SEL./ADJ. ENTER END
Main menu Sub menuPicture
Page 39
+30 -30Contrast
+30 -30
+30 -30
+30 -30
+30 -30+30 -30+30 -30
Tint Color
Sharp Bright
Red
Blue
*2*6 *2
*2 *1
*1
Progressive
Lamp Setting*2
Reset5500K
6500K
7500K
8500K
9300K
10500K
2D Progressive
3D Progressive
Film Mode
Bright
Eco + Quiet CLR Temp
Bright Boost [0/1/2]
Page 39
Page 40
Page 40
Page 40
Page 40
Page 40
Standard
Presentation
Movie
Game
sRGB*1 Picture Mode
Main menu Sub menuSCR - ADJ
Page 41
Language Image Shift Resize
Page 41
Page 41
Page 41
Page 41
Page 42
Page 42
Page 42
Page 42
Page 42
Keystone
Auto Keystone [On/Off]
OSD Display [On/Off]
Background
Setup Guide [On/Off]
PRJ ModeNormal
Border
Stretch
Logo
Blue
None
Front
Ceiling + Front
Rear
Ceiling + Rear
English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português +127 -127
+100 -100
+96 -96+75 -75
*5 *3
*4
*3
*4
*1 Items when inputting RGB signal through INPUT 1 or
INPUT 2.
*
2 Items when inputting component signal through INPUT 1 or
INPUT 2, or when selecting INPUT 3 or INPUT 4.
*
3 Adjustment range for PG-MB66X/PG-MB56X/XG-MB50X-L/
XR-11XC-L/XR-10X-L.
*
4 Adjustment range for XR-10S-L.
*5 An item which appears in the menu when using PG-MB66X
or PG-MB56X.
*
6 “Tone” will appear on the menu screen only when PAL or
SECAM signals are input (including when forcibly changed
to those input signals). There is basically no need to adjust
“Tone”, but you can adjust the picture tone with this
adjustment when inputting PAL or SECAM signals. • You can adjust the menu items with icons (
, ,
and ) using the respective buttons on the re-
mote control.
XR-11XCL_EN_i06.9.1, 11:36 AM 35 
						

							36
“Projector adjustment (PRJ-ADJ)” menu
Picture
Auto SearchSCR - ADJPRJ - ADJHelp
Auto Sync
Auto Power Off
System Sound
System Lock
h On On
On
On
SEL./ADJ. ENTER END0 Lamp Timer(Life) 100%
Speaker OnRS-232C 9600 bpsFan Mode Normal
Picture
There is no picture or audioSCR - ADJ PRJ - ADJHelp
Vertical stripes or flickering image appear
Data image is not centered
Color is faded or poor
Picture is dark
The image is distorted
Reset all adjustments to default settings
SEL. ENTER END
Main menu Sub menuPRJ - ADJPage 43Auto Search [On/Off]
Auto Sync [On/Off]
Auto Power Off [On/Off]
System Sound [On/Off]
Speaker [On/Off]
System Lock
Lamp Timer(Life)Page 43
Page 43
Page 43
Page 43
Page 43
Page 44
Page 44
Old Code
New Code
Reconfirm Fan ModePage 44Normal
High RS-232CPage 449600 bps
115200 bps
“Help” menuThe items you can set with the “Help”
menu
“Help” menu n Page 46• Vertical stripes or flickering image appear
Auto Sync
Adjust vertical noise
Adjust horizontal noise
• Data image is not centered
Auto Sync
H-Pos
V-Pos
• Color is faded or poor
INPUT 1 or INPUT 2
Signal type: Auto/RGB/Component
INPUT 3 or INPUT 4
Video System:Auto/PAL/SECAM/
NTSC3.58/NTSC4.43/PAL-
M/PAL-N/PAL-60
* The selectable items vary depending on the in-
put signal and the selected input mode.
Menu Items (Continued)
XR-11XCL_EN_i06.9.1, 11:36 AM 36 
						

							37
Useful
Features
Using the Menu Screen
Menu Selections (Adjustments)
Example: Adjusting “Bright”.• This operation can also be performed by using the buttons on the projector.
Press BMENU.• The “Picture” menu screen for the se-
lected input mode is displayed.
Adjustment buttons
(P/R/O/Q)
Example: “Picture” screen menu for INPUT 1
(RGB) mode
Press Q or O and select “Picture”
to adjust.
1
2
ENTER button
RETURN button
Menu item
Picture
Picture Mode
Contrast 0
0
0
0
K 7500SCR - ADJ PRJ - ADJ Help
BrightRedBlue
1CLR TempBright Boost
Lamp SettingStandard
Bright
Reset
SEL./ADJ. ENTER END
MENU/HELP
button Adjustment buttons (P/R/O/Q)
MENU/HELP button ENTER button
• Press lRETURN to
return to the previous
screen when the menu
is displayed.
XR-11XCL_EN_i06.9.1, 11:36 AM 37 
						

							38
Using the Menu Screen (Continued)
Press P or R and select “Bright”
to adjust.
• The selected item is highlighted.
• Press hENTER again to return to the
previous screen.
Press O or Q to adjust the item
selected.
• The adjustment is stored.
Press BMENU/HELP.• The menu screen will disappear.
3
4
5
0 Bright
Picture
SEL./ADJ. Rtn. Menu END
Picture
Picture Mode
Contrast 0
15
0
0
K 7500SCR - ADJ PRJ - ADJ Help
BrightRedBlue
1CLR TempBright Boost
Lamp SettingStandard
Bright
Reset
SEL./ADJ. Single ADJ END
Note
Picture
Picture Mode
Contrast 0
0
0
0
K 7500SCR - ADJ PRJ - ADJ Help
BrightRedBlueCLR TempBright Boost
Lamp SettingStandard
Bright
Reset
SEL./ADJ. Single ADJ END
Picture
Resize
Image Shift 0
0SCR - ADJPRJ - ADJ Help
KeystoneAuto KeystoneOff Normal
1
Items to be adjusted
• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Time”,
“FREEZE”, or “AV MUTE” functions.
Note
To adjust the projected
image while watching it
Press hENTER.• The selected item (e.g. “Bright”) is dis-
played by itself at the bottom of the
screen.
• When pressing P or R, the following item
(“Red” after “Bright”) will be displayed.The item displayed by itself
XR-11XCL_EN_i06.9.1, 11:36 AM 38