Sharp Xgmb50xl Manual

							Introduction Quick Start
SetupConnectionsBasic
OperationUseful
Features
Appendix
PROJECTEUR MULTIMÉDIA
MODELE
PG-MB66X/PG-MB56X
XG-MB50X-L
XR-11XC-L
XR-10X-L/XR-10S-L
MODE D’EMPLOI
MULTIMEDIA PROJECTOR
MODEL
PG-MB66X/PG-MB56X
XG-MB50X-L
XR-11XC-L
XR-10X-L/XR-10S-L
OPERATION MANUAL
IntroductionMise en route
rapideInstallation
Raccordements
Opération de
baseFonctions
pratiques
Appendice
XR-11XCL_cover06.9.12, 7:29 AM 1 
						

							IMPORTANT
• For your assistance in reporting the loss
or theft of your Projector, please record
the Model and Serial Number located on
the bottom of the projector and retain this
information.
• Before recycling the packaging, please
ensure that you have checked the con-
tents of the carton thoroughly against the
list of “Supplied accessories” on page 10.Model No.:
Serial No.:
XR-11XCL_EN_a06.9.1, 11:30 AM 2 
						

							1
IntroductionBefore using the projector, please read this operation manual carefully.
There are two important reasons for prompt warranty registration of your new SHARP
Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE.
WARNING:High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
WARNING:To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.
WARNING:FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void
the user’s authority to operate this equipment.
The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.
The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.
IntroductionENGLISH
See bottom of projector.
U.S.A. ONLY
U.S.A. ONLY
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTIONRISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
WARNING:The cooling fan in this projector continues to run for about 90 seconds after the projector enters
standby mode. During normal operation, when putting the projector into standby mode always
use the STANDBY/ON button on the projector or the STANDBY button on the remote control.
Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING
THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.
XR-11XCL_EN_b06.9.1, 11:30 AM 1 
						

							2
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the operation manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
U.S.A. ONLY
Declaration of conformity
SHARP PROJECTOR,MODEL PG-MB66X/PG-MB56X/XG-MB50X-L/XR-11XC-L/XR-10X-L/XR-10S-L
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Responsible Party:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP (1-800-237-4277)
U.S.A. ONLY
Caution Concerning Lamp Replacement
See “Replacing the Lamp” on page 52.
PRODUCT DISPOSALThis projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
This SHARP projector uses a DMD panel. This very sophisticated panel contains 786,432 (PG-
MB66X/PG-MB56X/XG-MB50X-L/XR-11XC-L/XR-10X-L) / 480,000 (XR-10S-L) pixels
(micromirrors). As with any high technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
XR-11XCL_EN_b06.9.1, 11:30 AM 2 
						

							3
Introduction
37
Useful
Features
Using the Menu Screen
Menu Selections (Adjustments)
Example: Adjusting “Bright”.•This operation can also be performed by using the buttons on the projector.Press BMENU.•The “Picture” menu screen for the se-
lected input mode is displayed.
Adjustment buttons
(P/R/O/Q)
Example: “Picture” screen menu for INPUT 1
(RGB) mode
Press Q or O and select “Picture”
to adjust.
1
2
ENTER button
RETURN button
Menu item
Picture
Picture Mode
Contrast 0
0
0
0
K 7500SCR - ADJ PRJ - ADJ Help
BrightRedBlue1CLR TempBright Boost
Lamp SettingStandard
Bright
Reset
SEL./ADJ. ENTER END
MENU/HELP
button Adjustment buttons (P/R/O/Q)
MENU/HELP button ENTER button
•Press lRETURN to
return to the previous
screen when the menu
is displayed.
How to Read this Operation Manual

The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
•In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
Info........Indicates safeguards for using the projector.
For Future Reference
Buttons used in
this operation
On-screen
display
Button used in
this step
Note.........Indicates additional information for setting up and operating the
projector.
Index Maintenance Troubleshooting
P.  6 6 P.  4 7PP. 61 and 62
XR-11XCL_EN_b06.9.1, 11:30 AM 3 
						

							4
Contents
Preparing
Introduction
How to Read this Operation Manual .... 3
Contents ............................................... 4
IMPORTANT SAFEGUARDS ............... 6
Accessories ........................................ 10
Part Names and Functions ................. 11
Inserting the Batteries.......................... 14
Usable Range...................................... 15
Quick Start
Quick Star t .......................................... 16
Using
Basic Operation
Turning the Projector On/Off .............. 27Turning the Projector on....................... 27
Turning the Power off (Putting the
Projector into Standby Mode)........... 27
Image Projection ................................. 28About the Setup Guide........................ 28
Adjusting the Projected Image............ 28
Switching the Input Mode.................... 30
Adjusting the Volume........................... 30
Displaying the Black Screen and Turning
off the Sound Temporarily................. 30
Correcting Trapezoidal Distortion........ 31
Resize Mode......................................... 32
Useful Features
Operating with the Remote Control .... 34Displaying and Setting
the Break Timer................................. 34
Auto Sync (Auto Sync Adjustment)..... 34
Freezing a Moving Image.................... 34
Selecting the Picture Mode.................. 34
Menu Items ......................................... 35
Using the Menu Screen ...................... 37
Menu Selections (Adjustments)........... 37Picture Adjustment (“Picture” menu) .. 39Selecting the Picture Mode.................. 39
Adjusting the Image............................. 40
Adjusting the Color Temperature......... 40
Setup
Setting up the Projector ...................... 18Setting up the Projector....................... 18
Standard Setup (Front Projection)....... 18
Ceiling-mount Setup............................ 18
Projection (PRJ) Mode......................... 19
Screen Size and Projection Distance .. 20
Connections
Connections ........................................ 21
Samples of Cables for Connection ..... 22
Connecting to a Computer ................. 23
Connecting to Video Equipment ......... 24
Connecting to a Monitor with RGB Input
Terminal ............................................ 25
Controlling the Projector by
a Computer ....................................... 26
Connecting the Power Cord ............... 26
Progressive........................................... 40
Lamp Setting........................................ 40
Adjusting the Projected Image
(“SCR - ADJ” menu) ......................... 41
Setting the Resize Mode...................... 41
Adjusting the Image Position............... 41
Keystone Correction............................ 41
Setting the On-screen Display............. 42
Selecting the Background Image........ 42
Selecting the Setup Guide................... 42
Reversing/Inverting Projected
Images............................................... 42
Selecting the On-screen Display
Language........................................... 42
Adjusting the Projector Function
(“PRJ - ADJ” menu) .......................... 43
Auto Search Function........................... 43
Auto Sync (Auto Sync Adjustment)..... 43
Auto Power Off Function...................... 43
Setting the Confirmation Sound
(System Sound)................................. 43
Speaker Setting.................................... 43
Selecting the Transmission Speed
(RS-232C).......................................... 44
Fan Mode Setting................................. 44
Checking the Lamp Life Status........... 44
System Lock Function.......................... 44
Locking the Operation Buttons on the
Projector (Keylock Function)............. 45
Troubleshooting with the “Help” menu ...46Utilizing the “Help” menu functions..... 46
XR-11XCL_EN_b06.9.1, 11:30 AM 4 
						

							5
Introduction
Reference
Appendix
Maintenance ....................................... 47
Cleaning and Replacing the Dust
Filters ................................................ 48
Maintenance Indicators ...................... 50
Regarding the Lamp ........................... 52
Lamp..................................................... 52
Caution Concerning the Lamp............ 52
Replacing the Lamp............................. 52
Removing and Installing
the Lamp Unit.................................... 53
Resetting the Lamp Timer.................... 54
Connecting Pin Assignments ............. 55
RS-232C Specifications and Command
Settings ............................................ 56
Computer Compatibility Chart ............ 60
Troubleshooting .................................. 61
For SHARP Assistance ...................... 63
Specifications ..................................... 64
Dimensions ......................................... 65
Index ................................................... 66
XR-11XCL_EN_b06.9.1, 11:30 AM 5 
						

							6
1. Read InstructionsAll the safety and operating instructions should
be read before the product is operated.
2. Retain InstructionsThe safety and operating instructions should be
retained for future reference.
3. Heed WarningsAll warnings on the product and in the operating
instructions should be adhered to.
4. Follow InstructionsAll operating and use instructions should be
followed.
5. CleaningUnplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
6. AttachmentsDo not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and MoistureDo not use this product near water–for example,
near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a
swimming pool; and the like.
8. AccessoriesDo not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may
fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with
the product. Any mounting of the product should
follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the
manufacturer.
9. TransportationA product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
IMPORTANT SAFEGUARDS
10. VentilationSlots and openings in the cabinet are provided
for ventilation to ensure reliable operation of the
product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing
the product on a bed, sofa, rug, or other similar
surface. This product should not be placed in a
built-in installation such as a bookcase or rack
unless proper ventilation is provided or the
manufacturer’s instructions have been adhered
to.
11. Power SourcesThis product should be operated only from the
type of power source indicated on the marking
label. If you are not sure of the type of power
supply to your home, consult your product dealer
or local power company. For products intended
to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or PolarizationThis product is provided with one of the following
types of plugs. If the plug should fail to fit into the
power outlet, please contact your electrician.
Do not defeat the safety purpose of the plug.
a. Two-wire type (mains) plug.
b. Three-wire grounding type (mains) plug with
a grounding terminal.
This plug will only fit into a grounding type
power outlet.
13. Power-Cord ProtectionPower-supply cords should be routed so that they
are not likely to be walked on or pinched by items
placed upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit from
the product.
14. LightningFor added protection for this product during a
lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from
the wall outlet and disconnect the cable system.
This will prevent damage to the product due to
lightning and power-line surges.
CAUTION: Please read all of these instructions before you operate this product
and save these instructions for later use.
Electrical energy can perform many useful functions. This product has been engineered
and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the
safeguards incorporated in this product, observe the following basic rules for its installation,
use and servicing.
XR-11XCL_EN_b06.9.1, 11:30 AM 6 
						

							7
Introduction
15. OverloadingDo not overload wall outlets, extension cords, or
integral convenience receptacles as this can
result in a risk of fire or electric shock.
16. Object and Liquid EntryNever push objects of any kind into this product
through openings as they may touch dangerous
voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any
kind on the product.
17. ServicingDo not attempt to service this product yourself as
opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
18. Damage Requiring ServiceUnplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power-supply cord or plug is
damaged.
b. If liquid has been spilled, or objects have fallen
into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive work
by a qualified technician to restore the product
to normal operation.
e. If the product has been dropped or damaged
in any way.
f. When the product exhibits a distinct change
in performance, this indicates a need for
service.
•DLP® and the DLP logo are registered trademarks of Texas Instruments.
•Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
•PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
•Macintosh
® is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
•All other company or product names are trademarks or registered trademarks of their
respective companies.
•Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
19. Replacement PartsWhen replacement parts are required, be sure
the service technician has used replacement
parts specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Safety CheckUpon completion of any service or repairs to this
product, ask the service technician to perform
safety checks to determine that the product is in
proper operating condition.
21. Wall or Ceiling MountingThis product should be mounted to a wall or
ceiling only as recommended by the
manufacturer.
22. HeatThis product should be situated away from heat
sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that
produce heat.
XR-11XCL_EN_b06.9.1, 11:30 AM 7 
						

							
8Observe the following safeguards when setting up your
projector.
Caution concerning the lamp unit


Potential hazard of glass par-
ticles if lamp ruptures. In
case of lamp rupture, contact
your nearest Sharp Autho-
rized Projector Dealer or Ser-
vice Center for replacement.
See “Replacing the Lamp” on
page  52.
Caution concerning the setup of the pro-
jector

 For minimal servicing and to maintain high
image quality, SHARP recommends that this
projector be installed in an area free from
humidity, dust and cigarette smoke. When the
projector is subjected to these environments,
the vents and lens must be cleaned more of-
ten. As long as the projector is regularly
cleaned, use in these environments will not
reduce the overall operation life of the unit.
Internal cleaning should only be performed
by a Sharp Authorized Projector Dealer or
Service Center.
Do not set up the projector in places ex-
posed to direct sunlight or bright light.

Position the screen so that it is not in direct
sunlight or room light. Light falling directly on
the screen washes out the colors, making
viewing difficult. Close the curtains and dim
the lights when setting up the screen in a
sunny or bright room.
Caution regarding placing of the projec-
tor

Place the projector on a level site within the
adjustment range (8 degrees) of the adjust-
ment foot.
When using the projector in high-altitude
areas such as mountains (at altitudes of
approximately 1,500 meters (4,900 feet)
or more)

When you use the projector in high-altitude
areas with thin air, set “Fan Mode” to “High”.
Neglecting this can affect the longevity of the
optical system.
Warning about placing the projector in
a high position

When placing the projector in a high position,
make certain it is carefully secure to avoid
personal injury caused by the projector fall-
ing down.
Do not subject the projector to hard im-
pact and/or vibration.

Protect the lens so as not to hit or damage
the surface of the lens.
Rest your eyes occasionally.

Continuously watching the screen for long
hours will cause eye strain. Take regular
breaks to rest your eyes.
Avoid locations with extremes of tem-
perature.

The operating temperature of the projector is
from 41°F to 95°F (+5°C to +35°C).

 The storage temperature of the projector is
from  –4°F to 140°F (–20°C to +60°C).
Do not block the exhaust and intake
vents.

Allow at least 11 13/16 inches (30 cm) of space
between the exhaust vent and the nearest
wall or obstruction.

 Be sure that the intake vent and the exhaust
vent are not obstructed.

 If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion. (See pages  50 and  51.) Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.

 After the projector is purchased, a faint smell
from the vent may appear when the power is
first turned on. This is normal and is not a
malfunction. It will disappear after the projec-
tor is used for a while.
XR-11XCL_EN_b 06.9.11, 11:07 AM
8